These are brand new cnc machined and made of solid billet aluminum.
1/4 in thick by 13-3/4 by 1-1/2 all edges have 1/8 inch radius, and includes stainless steel hardware. No drilling bumper screws into existing holes.

Alot cheaper than what others sell cause I make them myself on a state of the art CNC miller.

Asking 30 shipped anywhere the US except alaska and hawaii

I only made 3 to try selling and one for my car wich is why I started making them to begin with, If more is wanted I'll make more.

If you want I can engrave a club name or company name on these if enough is ordered. PM me with questions.

!!!And yes I know my car is dirty!!! I'll work on that.



http://www.hostpic.biz/uploads/987eb150bd.jpg (http://www.hostpic.biz)
http://www.hostpic.biz/uploads/d7ca7fe29e.jpg (http://www.hostpic.biz)
http://www.hostpic.biz/uploads/8d42ce1bd2.jpg (http://www.hostpic.biz)

I'd buy one if it was shaped for an '06. I made one out of thinner aluminum flat bar and painted it black. Rock chips have taken their tole on the thing. Your piece looks a little slicker - CNC, ftw!
If I had one from you to fit an '06, I'd have it hard anodized black. The finish would last a little longer (I think).

I'd buy one if it was shaped for an '06. I made one out of thinner aluminum flat bar and painted it black. Rock chips have taken their tole on the thing. Your piece looks a little slicker - CNC, ftw!
If I had one from you to fit an '06, I'd have it hard anodized black. The finish would last a little longer (I think).


yeah my shop does hard anodizing but it is a little costly. but it looks real good!!! and yes it last a long time. I can probably do one for an 06 too but I need to get my hands on an 06 to take measurments, if enough people want one a buddy of mine has an 06 I could use for a couple of minutes and I could start those up.

30 too much???

I'd be interested in an '06

$30 is pretty close to what the others charge, I think. Subiesport, Autospeed, a couple others...

If I **begged** ... would you make one for we 93-01 Impreza guys? Nobody seems willing. :)

-Chris

$30 is pretty close to what the others charge, I think. Subiesport, Autospeed, a couple others...

If I **begged** ... would you make one for we 93-01 Impreza guys? Nobody seems willing. :)

-Chris

I don't have access to that body style front bumper to make oneI would need dimentions or the bumper

I can get you anything you want. Except the bumper. :)

Measurements I can do. It's basically a rectangle, no angle cuts or anything. Let me know what you need!

Where exactly are you located? I'm a former NESIC'er, there's an awful lot of GC/GM bodystyles still left up there (GFs too). North Ursalia or any number of them would gladly donate their car for measurements, I'm sure, if you need it in person.

-Chris

pm'ed!!!!

im up for an 06 one, PM me

I can get you anything you want. Except the bumper. :)

Measurements I can do. It's basically a rectangle, no angle cuts or anything. Let me know what you need!

Where exactly are you located? I'm a former NESIC'er, there's an awful lot of GC/GM bodystyles still left up there (GFs too). North Ursalia or any number of them would gladly donate their car for measurements, I'm sure, if you need it in person.

-Chris
send me overall measurments and hole to hole dimentions and i can see what i can do

Just need height/width?

Just need height/width?
yup and how to mount it to the bumper center to center distance of the holes but since i don't have it to measure it's kinda a shot in the dark

I'll do my best. Didn't get a chance today, but hopefully by the end of the weekend.

=Chris

All Out Let Me Know If You Want One I'll Fire Up The Cnc And Crank More Out

Please Pm Me

I have no idea what these look like...

Can you send me a pic? They aren't up on your first post anymore.

niiiiiice

Sorry 'bout the delay, took some measurements earlier. I can try to snap a photo or two if you need it...

width = 12.5"
height = 2.0"
inside of hole -to- inside of hole = 6 7/8"
outside of hole -to- outside of hole = 7 1/4"
top to top-of-hole = 1 1/8"
top to bottom-of-hole = 1 3/8"
bottom to top-of-hole = 7/8"
bottom to bottom-of-hole = 3/4"


So the (screw/mounting) holes are located not halfway down, vertically. Off-center.

The width is tricky. The edges curve toward the back of the bumper, 12.5" will cover the front flat part before it starts to curve back. 12.75" would over-extend I think.

Might not be on much for a few days, got these pics then my Mom called from SC... her house got robbed tonight, they punched my grandmother (who is 97) in the jaw and stole a bunch of stuff. She's in the hospital. Dunno if I have to drive down yet or not.

*sigh* ...People.... :(

Chris

Oh man soo sorry to hear.

Photos would be nice. I still have no idea what a front plate eliminator looks like. :(

Hmm I guess his pics aren't up anymore...

Here's the one for the WRX and STi from Autospeed:

http://www.autospeedperformance.com/Subaru/Btrim.jpg

(http://www.autospeedperformance.com shows the rest of the designs.)


And Subiesport Magazine's version:

http://www.carzines.com/mer-tp2.html


Autospeed has one for the '06 too, they have a couple of shapes. Nobody seems to think that enough GC/GM/GF people would buy them, though. I've been trying to get people to make us one for years.

=S2=

Hmm so what does fastsubaru8 look like? Can we get personal engraving? :)

got mine, looks good

BUMP!

Any luck trying the GC ones?...........


-S2-

funny you asked I haven't looked at this ad in a long time and I happened to take mine off the car today to have it anodized. but no I haven't tried to make other year or models. not enough people want them for me to fire up the ol cnc. but I did just buy a set of cobb rear endlinks and relized I can make them for cheap$$$ If anyone is interested.

Ahh, bummer.

For you I understand, not being a company...

But the other guys say that there's not enough interest from GC/GM/GF owners... I just don't buy it. There's still a lot of us out there. 1993-2001 is a long run of cars. :cool: