http://www.iagperformance.com/images/forum/nasioc/service/image_01_800.jpg (http://www.iagperformance.com/general_service.html)



About Us:
IAG Performance is a complete performance & service center, able to take on the smallest or largest projects. At IAG, we are very familiar with the entire Subaru line of vehicles and you can feel comfortable knowing your STI, WRX, Forester XT, Legacy GT, or naturally aspirated Subaru is in good hands while work is performed. Our customers' satisfaction and comfort during service is our number one priority! We are not about inflated service tickets or one time visits... At IAG, we hope to build long-term relationships that last a lifetime!


A quick shot of our showroom:
http://www.iagperformance.com/images/forum/nasioc/service/image_02_800.jpg



IAG Performance Subaru Scheduled Maintenance Services

http://www.iagperformance.com/images/forum/nasioc/service/image_05_800.jpg

30,000 & 90,000 Mile Service - $399
-Oil change using your choice of Motul, Eneos or Valvoline Synthetics
-K&N or Purolator Pure One Oil Filter & new drain plug washer
-Replace Transmission Fluid w/ Motul 75w90 (Motul Gear300 and other fluids available upon request)
-Replace Differential Fluid w/ Motul 75w90 (WRX) or Motul PA 90 (STi)
-Coolant flush and inspect cooling system, hoses and connections. Global coolant w/ 1 bottle of Motul MoCool
-Air Filter Service (replace factory filter w/ K&N Drop-In, or clean & lubricate existing filter)
-Flush & replace brake fluid w/ your choice of Ate SuperBlue or Motul DOT 5.1
-Inspect brake pads and rotors
-Inspect brake lines and check operation of parking brake
-Inspect Front & Rear axle boots and axle shaft joint portions
-Inspect clutch operation
-Inspect Steering & Suspension
-Inspect tires & rotate
-PCV Valve
-Top-off all fluids
-Replace fuel filter (vehicles vary) and inspect fuel system


60,000 Mile Service - $499
-All services performed in 30K Service
-Change spark plugs


http://www.iagperformance.com/images/forum/nasioc/service/image_04_800.jpg

105,000 Mile Service - $899
-Replace Timing belt
-Replace water pump & water pump gasket
-Replace thermostat & thermostat gasket
-Flush coolant & inspect cooling system. Global coolant w/ 1 bottle of Red Line Water Wetter or Motul MoCool
-Crank Seal
-A/C & P/S Belts
-Cam Seals
-Timing belt tensioner

Timing Belt/Water Pump Service Only - $499


Brake Packages

http://www.iagperformance.com/images/forum/nasioc/service/image_07_800.jpg

Stage 1
Hawk HPS Front/Rear Pads
Techna-Fit SS brake lines
Motul DOT 5.1 or Ate SuperBlue
WRX - $449 Installed
STi - $499 Installed
Also available for other Subaru models - Call/PM for details and pricing!

Stage 2
Hawk HPS Front/Rear Pads
Techna-Fit SS Brake Lines
Motul DOT 5.1 or Ate SuperBlue
RacingBrake/DBA Slotted or Cross-Drilled & Slotted Rotors
WRX - $949 Installed
STi - $1099 Installed
Also available for other Subaru models - Call/PM for details and pricing!

Suspension Services

http://www.iagperformance.com/images/forum/nasioc/service/image_06_800.jpg

Alignment/Corner Balancing
Performance Alignment - $99
Performance Alignment & Corner Balancing - $199
Install Springs/Coilovers (purchased @ IAG) w/ Performance Alignment - $250
Install Customer supplied springs & alignment - $349
Install Customer supplied coilovers & alignment - $399


Fender Rolling Services

http://www.iagperformance.com/images/forum/nasioc/service/image_07_800.gif

$75 - Roll rear fenders
$99 - Roll & pull rear fenders
$125 - Roll all 4 corners
$149 - Roll & pull all 4 corners
Fender rolling service pricing may vary depending on vehicle/extend of service - Call/PM for details!


Transmission Services

http://www.iagperformance.com/images/forum/nasioc/service/image_08_800.jpg

Exedy Stage 1 clutch package – w/ resurfaced flywheel & Motul or Eneos 75w90 fluid
WRX - $899 Installed
STi - $999 Installed
Also available for other Subaru models - Call/PM for details and pricing!

Exedy Twin-Plate clutch package w/ performance flywheel & Motul or Eneos 75w90 fluid
WRX - $1899 Installed
STi - $1899 Installed
Also available for other Subaru models - Call/PM for details and pricing!

Other clutch purchased @ IAG installation prices (includes resurfacing flywheel and new fluids)
WRX & STi - $400

Install customer supplied clutch (includes resurfacing flywheel and new fluids)
WRX & STi - $495

New ACT Specials (others available - PM/Call for details!)

ACT SB5-HDSS - ACT Heavy-Duty Modified Street Clutch with your choice of ACT Streetlite or Subaru OE 06-07 WRX Flywheel - $1349 Installed with your choice of fluids!!!

ACT HDSS STI Heavy Duty Street Clutch - ACT Heavy-Duty Modified Street Clutch with resurfaced flywheel for 04-09 STI 6-Speed - $1199 Installed with your choice of fluids!!!


Performance Part Installs

Downpipe/Turboback (purchased @ IAG) - $79
Downpipe/Turboback (customer supplied) - $99
Uppipe Install (purchased @ IAG) - $225
Uppipe Install (customer supplied) - $300
Sway-Bar/end-link Install - $79
Upgraded Turbo Install - Please call or PM
Front-Mount Intercooler Install - Please call or PM
The IAG Performance Rotated Turbo Setup - Please call or PM
Installation of thousands of other products for your Subaru - PM for pricing!!!


Protuning by Jorge (riftswrx)

$500 for 2 hour tuning session

$99 for IAG Pre-Dyno Inspection - Includes compression test and check for boost leaks - Complimentary full-support on the dyno if this service is performed prior to tuning!

See Post #2 for details on our Tuning Sessions with Jorge!!!

Appearance Services & Window Tint

http://iagperformance.com/images/forum/nasioc/service/image_09_800.jpg

Window Tinting @ IAG Performance

Our window tinter has been in the business for over 15 years, and does an absolutely incredible job. We offer Johnson high quality window films, available in shades from MD legal all the way to limo dark.

Our tinting services come with a lifetime warranty against bubbling, peeling, fading, purpling, hazing, & more.

If you're looking for high-quality tint for your Subaru, shoot us a PM or call at the shop any time!

Other Appearance Services

Recondition headlights - $75

Koji-Mod & Paint headlights (your choice of color, typically black)
WRX - $199
STi - $225

Headlight and Taillight Protection Films - Price varies - PM for details!

A shot of our shop:
http://www.iagperformance.com/images/forum/nasioc/service/image_03_800.jpg

IAG Performance
1203 Baltimore Blvd.
Westminster, MD 21157
410-840-3555
www.iagperformance.com (http://www.iagperformance.com/)
sales@iagperformance.com (sales@iagperformance.com)

http://iagperformance.com/images/forum/nasioc/service/image_10_800.jpg
Pro Tuning by Jorge (RiftsWRX)

As many of you may know IAG and RiftsWRX (Jorge Carillo) have teamed up to bring the MAIC community regular dyno-tuning sessions each month. Jorge has an absolutely outstanding reputation tuning Subarus, and is one of the most renowned Accessport Pro-tuners in the country!

How It Works...
Tuning spots are available for $500 and you will receive UP TO 2 hours of dyno tuning. Sometimes, it will take the whole session to finish up your tune... Other times, it may take only an hour or so. At this point, if you are satisfied, you are welcome to go on your way. However, if there is enough remaining tuning time, you have the option of adding a second tune for race gas or meth. Many of our tuning customers choose to add a race-gas map in addition to their street maps.

Successful preparation leads to successful tuning!!!
To tune with us at IAG Performance, we are now requiring that you have a PDI (Pre-Dyno Inspection) performed on your vehicle prior to tuning. This service will need to be performed at our facility sometime in the several weeks prior to tuning. Pre-dyno inspections WILL NOT be performed the weekend of tuning, as we need to have all cars 100% ready to go prior to Jorge flying in.

The IAG Performance Pre-Dyno Inspection
-IAG performs a compression test and changes plugs if needed
-IAG performs both boost and vacuum leak test
-IAG checks car over for major oil or exhaust leaks
-IAG changes oil and filter (oil & filter sold separately)
-IAG looks over car carefully to ensure it is in tunable condition.

Pre-Dyno Inspection will be performed at a discounted rate of $99. At most tuning shops, the services offered for our Pre-Dyno Inspection would run roughly $250, but we want to do everything in our power to be sure that these tuning days run as smooth as possible. Performing these services does not necessarily guarantee a 100% perfect tuning day, but it does mean that we have made every effort to come equipped and give the tuner a vehicle that has been fully prepared for Pro-tuning.

What happens if there is a problem on the dyno? You receive the full support and expertise of both our owner and lead technician. We will wrench on your car and do everything in our power to ensure a successful tune. Of course, we can never guarantee that every car will go without issues, but this is our guarantee that we will do everything in our power to try to make your tuning day a success! As always, we bring a huge care package of spare parts and tools to be able to deal with any problems that may arise.

What do we need from you? If you would like to reserve a tuning spot, please PM, email, or call us. We require a $250 deposit to hold your spot. Tuning spots will be sold on a first come first serve basis, and a spot is only considered filled when we receive the deposit. Deposits can be made via Paypal, major credit card by calling us, or in person by cash or check. DO NOT send a deposit without speaking to us first. Please contact us with any questions regarding tuning, installation, pre-dyno, etc. PRIOR to making your deposit, as it is non-refundable (see below)

Important Note:
If you cannot make your dyno session for any reason, your $250 deposit is NOT refundable. We make a commitment to this session and to our tuner, and we are interested in working with customers who share that same level of commitment. In certain circumstances, if we are able to fill the tuning spot, we can apply your $250 to a future tuning session, should catastrophic circumstances arise. The most important thing to us, is that before you make your deposit, you are 100% committed to tuning!


Frequently Asked Questions

Where does IAG Tune? As you may have seen in our recent MAIC post, we have completed install of our new in-house DynoJet! Tuning now takes place exclusively at our facility in Westminster, MD!

What kind of engine management does Jorge tune at the IAG sessions? The primary tuning device that we tune is the Cobb Accessport. Jorge will also tune stand-alone devices such as AEM for some customers. We DO NOT offer tuning for UTEC or OpenSource. For more details, feel free to call or email with questions.

When will I find out my tuning time? We will notify tuning customers some time the week prior to tuning with a finalized schedule. We take customers’ desired times in to consideration, but this does not guarantee that everyone will receive their desired time on the nose (example, typically at least 5 customers want to tune in the first spot on Saturday…)

If I have performance upgrades installed on my car prior to the tuning date, will my car be safe to drive until that weekend? Jorge can build a “safe file” for your Cobb AP. We will need at least 1 week lead-time to order these files and have them ready.

In short, you can’t beat $500 for up to two pro-tuned maps by one of the best Cobb tuners in the country and the on-hand support of our experienced staff to back you up. We feel that the MAIC community deserves this level of tuning and care and are glad to be a part of it. If you have any questions please PM, call or email the shop. If you can’t make it to this session, don’t worry, there will be many more! :)


Regards,

Rick
IAG Performance
sales@iagperformance.com
410-840-3555

Important note: For tuning specific questions, please feel free to contact Jorge at Jorge@iagperformance.com. DO NOT contact Jorge at P&L Motorsports for any reason. If you need to reach him, contact him via this email address or call here at the shop!


http://www.iagperformance.com/images/dyno/protuning/image_02_635.jpg

What are the future dates for tuning sessions?

What are the future dates for tuning sessions?

The next date is next weekend, Saturday Feb 28 and March 1. There is one remaining spot, so if you're interested, shoot us a PM as soon as possible!

Beyond that, we have not selected dates yet for our March session. I will post up when we have some dates! :)

Regards,

Rick

Will Jorge Protune V1 accessports too?

Yes he will!
And you guys need a shop webcam...

Will Jorge Protune V1 accessports too?

Yes he will (thanks John!).. We actually have one spot left available for this month.. Let us know if you're interested (there is another thread about it here in the MAIC Vendor Classifieds!)

Rick

can i do a group buy on service packages...the silver xt needs a 90 and the red xt is gonna need a 60 soon???

Thanks again for taking care of me yesterday. There's a reason I drive 48 miles for you guys for an oil change.

Didn't realize you guys were doing Dyno's on the 28th, I sent you an email about getting some generic stuff done (oil change, steering rack bushings and tail tint). Should I try to schedule for a different day?

can i do a group buy on service packages...the silver xt needs a 90 and the red xt is gonna need a 60 soon???

I'm sure we can work out a package deal. I'd definitely like to help you get the silver car sold so you can get your head focused on more important things (like 10 second Foresters...) :lol:

Thanks again for taking care of me yesterday. There's a reason I drive 48 miles for you guys for an oil change.

No problem! We certainly appreciate your business!

Didn't realize you guys were doing Dyno's on the 28th, I sent you an email about getting some generic stuff done (oil change, steering rack bushings and tail tint). Should I try to schedule for a different day?

You've got email, sir! :)



Reminder for the day: One last tuning spot available for February 28/March 1!!! PM for details!

Rick

I know you guys stock seibon right? I was looking for this lip for my car that I havent seen much http://www.seiboncarbon.com/pdut_detail_pic.asp?ItemID=515
If you guys could get this that would be awesome

I know you guys stock seibon right? I was looking for this lip for my car that I havent seen much http://www.seiboncarbon.com/pdut_detail_pic.asp?ItemID=515
If you guys could get this that would be awesome


RIIIIIIIICCCCCCKKKKKKKK!!!!! pickticket

I know you guys stock seibon right? I was looking for this lip for my car that I havent seen much http://www.seiboncarbon.com/pdut_detail_pic.asp?ItemID=515
If you guys could get this that would be awesome

Sent you a PM... I'm sorry, I saw your post last weekend when we were down at the tuning session and completely forgot to PM you when we got back!

Rick

Bump for me sending you a PM

Bump for me sending you a PM


Right back at ya!

Bump! I sent you a PM.

Bump! I sent you a PM.

Thanks for the bump. Looking forward to your appointment! :)

Rick

So I have been slacker recently and I should have posted this earlier, but a huge thanks guys. The guys at IAG did a great job on corner balancing my 04 STi. Thanks again for the spanner wrench as well! You can expect a call from me tomorrow!

So I have been slacker recently and I should have posted this earlier, but a huge thanks guys. The guys at IAG did a great job on corner balancing my 04 STi. Thanks again for the spanner wrench as well! You can expect a call from me tomorrow!

Josh,

I don't think we ever heard from you! I'll shoot you a PM to see what's up! Thanks for the kind words! :)

Rick

PM'd.....

PM'd.....

PM'd back! :)

was wandering around westminster today and happened to see the shop (stopped in a little after 7pm and chatted).

marking this for later as my 105k service will be coming up soon.

Thanks again for the work guys.
http://forums.nasioc.com/forums/showthread.php?p=26177453&posted=1#post26177453
(yes its a cross post, and no I don't care!)

was wandering around westminster today and happened to see the shop (stopped in a little after 7pm and chatted).

marking this for later as my 105k service will be coming up soon.

It was very nice meeting you the other night and chatting! Stop by sometime during the day when you get a chance, and I'll finish showing you around the shop! :)

Thanks again for the work guys.
http://forums.nasioc.com/forums/showthread.php?p=26177453&posted=1#post26177453
(yes its a cross post, and no I don't care!)

John,

Thanks again for the review. We greatly appreciate your business, and look forward to working with you in the future!!!

Rick

You guys will always have business from me :)

PS. Rick or JJ did you get my PM? I just want to make sure.

You guys will always have business from me :)

PS. Rick or JJ did you get my PM? I just want to make sure.

Thanks Cesar! I just re-sent your email!

how far ahead are you guys booked? thinking of tbe and tint

how far ahead are you guys booked? thinking of tbe and tint


For most things, we are booked until May 4th during the week and in to June for Saturdays.

That being said, something as simple as TBE and tint, we could get you in anytime. Let us know if you have any questions.

Regards,
JJ

good deal...I can come during the week. I need to wrap the DP and get the exhaust to the powdercoaters, then I'll give you a ring.

We have added ACT Clutches to our product line for those who are interested! Shoot us a PM or call for details!

Rick

I had coilovers, wheels and tires installed on my WRX this week with an alignment by IAG and the service was great along with the price.
Another happy customer.

I had coilovers, wheels and tires installed on my WRX this week with an alignment by IAG and the service was great along with the price.
Another happy customer.

Karl,

Glad to hear you were happy with everything! The ride-height difference paired with those new wheels and tires looked absolutely awesome! :)

Rick

PM'ed ya.

Got any good deals on strut/springs combo for an 04 wrx?

do you guys have wifi at the shop? just wondering if I should bring my laptop along to do some work while I wait.

Got any good deals on strut/springs combo for an 04 wrx?

Shot you a PM!

do you guys have wifi at the shop? just wondering if I should bring my laptop along to do some work while I wait.

Yes, we do! It does have a code though... See Nick when you're up here and he'll get you all set up! :)

Rick

excellent. with work being as it is at the moment, I really shouldn't be away tomorrow but looks like I can do it and not be missed (much)

PM sent!

PM sent!

PM replied! :)

PM replied! :)

Replied to your PM reply.;)

Replied to your PM reply.;)

So I suppose I'll keep this going... I just replied to your reply to my reply (i think.... :lol:)

Rick

how much to get windows tinted on a 2002 subaru wrx (non wagon), few other things i might want done (stock headlights reconditioned and painted black) ill have to get to you on when i can do this and what not. but a price on the tinting would be cool

I need mine tinted too.....been putting it off

how much to get windows tinted on a 2002 subaru wrx (non wagon), few other things i might want done (stock headlights reconditioned and painted black) ill have to get to you on when i can do this and what not. but a price on the tinting would be cool

Johnson Window Films Greystone Line with Lifetime Warranty is normally $239.99 but for forum members, we discount the service to $199.99. It is a very high quality tint that is non-metallic and non-dyed. We have a full time tinter here 6 days a week. Let us know when you are ready.

I need mine tinted too.....been putting it off

Dan, maybe on your next trip up. Hope to see you again soon.

Regards,
JJ

I can vouche for the tint! My last tint was a brownish tint, this is much better quality and is more of a smoke color from the inside. They did a great job and it kind of baffles me how they can cut a line so straight... Looks factory.

To the top!

I am @ IAG now.

my IAG tint looks great.

also, thanks guys for the alignment, it ****ing rips, just ask anyone who went to the skyline camp and cruise. unbelievable the way this WRX handles now. awesome job.

30K Mile Service - Completed (even though I was at 40,3xx) :lol:

can get a ETA on my order?

I emailed you guys on Thursday of last week twice and called on Friday and was told I'd get a call back, which of course never came. I made my order on May 4th.

I'm not sure what else to do. I've tried PM, email, and phone call. I've got every bolt on imaginable from the intake to the TBE in my room waiting to get put on. I am literally sleeping with my downpipe because I ran out of room to store this stuff.

All I ordered was headers and 44mm uppipe (got my EWG from MA), which I know you guys have in stock (or so you told me). I'll even come by and pick it up if you can just get my parts together. I know you guys have a ton of business, but if you can't get this stuff together can you please at least let me know so I can just get a different uppipe?

can get a ETA on my order?




I am incredibly sorry that someone did not get back to you. I will be sure to find out why! Your order should be ready by Tuesday at the latest. Please call me at the shop tomorrow at your convenience so I can make it up to you.

Regards,
JJ

You can ignore the PM I sent ;-)

See you tomorrow for my 105k service!

Hey JJ, thanks for the call back and update. I appreciate it and can't wait for my stuff to get here :)

PM'd ...

You can ignore the PM I sent ;-)
See you tomorrow for my 105k service!

Peter - Glad we could get you in and taken care of! Have a great weekend! :)

Hey JJ, thanks for the call back and update. I appreciate it and can't wait for my stuff to get here :)

Bill - Just tracked your package and saw that it had been delivered today. Left you a message to follow up! I'll look forward to hearing back from you!

PM'd ...

PM returned!


Rick

PM'd.

Bill - Just tracked your package and saw that it had been delivered today. Left you a message to follow up! I'll look forward to hearing back from you!


Sorry I didn't call you back. I got the headers, everything looks great (esp the uppipe and dump tube).

Thanks again for all the follow up. You guys are A+ as always.

much more love to Rick & IAG. You guys getting that thermal wrap to DPS tomorrow is what will allow me to have my car this weekend (assuming I dodge the rest of these installation bullets :banana:)

pm'd you guys about getting some tires

pm'd you guys about getting some tires


PM returned!

So I got my 30k service yesterday and Subaru wanted $150 to change my differential/trans fluids yet you guys offer those in the 30k package.......

Bastards. I know where I'm going for my 90k.

They also wanted $120 to change my cabin filter :lol:

So I got my 30k service yesterday and Subaru wanted $150 to change my differential/trans fluids yet you guys offer those in the 30k package.......

Bastards. I know where I'm going for my 90k.

They also wanted $120 to change my cabin filter :lol:

Ha thats nothing Subaru wanted $250.00 just to change my diff/trans fluids. I said no thanks and I plan on going to IAG for the service.

PM sent about some special services ;)

They also wanted $120 to change my cabin filter :lol:

I'll do it for $50! ;)

So I got my 30k service yesterday and Subaru wanted $150 to change my differential/trans fluids yet you guys offer those in the 30k package.......

Bastards. I know where I'm going for my 90k.

They also wanted $120 to change my cabin filter :lol:

We'll look forward to hearing from you! :)

Ha thats nothing Subaru wanted $250.00 just to change my diff/trans fluids. I said no thanks and I plan on going to IAG for the service.

Cesar,

I'll be giving you a shout next week... I'm working on firming things up w/ Jorge!

PM sent about some special services ;)

PM'd you back!

Rick
IAG Performance

PM sent

All PM's returned! :)

Pm Sent!!

Pm Sent!!

Replied

Pm'd you

I would like to set up an appointment for a Stage 2 brake install for my 2005 Forester XT: slotted rotors with ATE super blue fluid.

I am hoping that Monday the 15th of June is open. Let me know.

Thanks.

Michael Donnelly

PM'ed ya for a quote.

WhiteLine FSB 24mm adjustable
WhiteLine Steering Rack Bushings

Thanks

-Jeff

Pm'd you

PM Replied!

I would like to set up an appointment for a Stage 2 brake install for my 2005 Forester XT: slotted rotors with ATE super blue fluid.

I am hoping that Monday the 15th of June is open. Let me know.

Thanks.

Michael Donnelly

Sent you a PM

PM'ed ya for a quote.

WhiteLine FSB 24mm adjustable
WhiteLine Steering Rack Bushings

Thanks

-Jeff

PM Replied!


Rick

thanks again for your services,

Just had the fenders rolled and pulled to fit the new 18x8.5 royal sports bronze rota svn's with 255/35/18 star specs on the forester. next year when it it time for new shoes again we are gonna go thicker since there is plenty of room

Pm'd you about gauges.

thanks for the work yesterday guys. car is much nicer :D

One Q - there's a rattle with the Cobb short-throw. From what I've read, this is normal on the 6sp due to a poor fitting pin in the rear lockout ring. Any solutions you know of?

thanks again for your services,

Just had the fenders rolled and pulled to fit the new 18x8.5 royal sports bronze rota svn's with 255/35/18 star specs on the forester. next year when it it time for new shoes again we are gonna go thicker since there is plenty of room

Thanks Vince! Glad we could get you back on the road again! I'm definitely very fond of that wheel/tire setup on the FXT! :)

Pm'd you about gauges.

PM returned, and gauges should be on their way shortly!

thanks for the work yesterday guys. car is much nicer :D

One Q - there's a rattle with the Cobb short-throw. From what I've read, this is normal on the 6sp due to a poor fitting pin in the rear lockout ring. Any solutions you know of?

Dan,

Thanks again for coming up Monday! The shifter noise is indeed common. I shot you a PM about your next trip up! :)

Rick

Awesome Guys. Went up tuesday for transmission and clutch. Got it done while i waited. Thanks for the call today Rick for the follow up. Car is running great, much stiffer clutch too. Thanks a lot. As stated yesterday, ill be coming up to get work done all the time. Also I told my friends and they want to come up and check the shop out and what not next time i get something. So other than a bugeye, ya might have my friend (if he gets his subaru that he told you he wanted) in a hawkeye, another in a possible hawkeye or blob, and my best friends evo. Well thanks a bunch, and will be in contact soon for probable tint or body mods. Also might get an AP, cuz Jorge might be coming back. Cant wait for the IAG meet.

Bobby

Pm'ed for service quote.

Awesome Guys. Went up tuesday for transmission and clutch. Got it done while i waited. Thanks for the call today Rick for the follow up. Car is running great, much stiffer clutch too. Thanks a lot. As stated yesterday, ill be coming up to get work done all the time. Also I told my friends and they want to come up and check the shop out and what not next time i get something. So other than a bugeye, ya might have my friend (if he gets his subaru that he told you he wanted) in a hawkeye, another in a possible hawkeye or blob, and my best friends evo. Well thanks a bunch, and will be in contact soon for probable tint or body mods. Also might get an AP, cuz Jorge might be coming back. Cant wait for the IAG meet.

Bobby

Bobby,

Thanks very much for coming up! Glad we could get you all squared away. Hopefully we'll have info on our open house coming soon!

Pm'ed for service quote.

PM'd back and forth a few times :)

Rick

When will the next IAG swap meet / get together event be held?

Just wanted to say thanks for a great job with the alignment and corner balance! Though I haven't yet had the opportunity to do an autox or track day, it's clear that the car's handling is much improved. It was also a nice bonus to run into Myles at your shop. Good guy. Thanks, again, and I'll definitely be by in the future, as the need arises.

best,

thane

When will the next IAG swap meet / get together event be held?

We are talking about things hopefully in the coming weeks... I would expect our Open House to take place around the same time as last year (September). Announcement will follow in the coming weeks! :)

Just wanted to say thanks for a great job with the alignment and corner balance! Though I haven't yet had the opportunity to do an autox or track day, it's clear that the car's handling is much improved. It was also a nice bonus to run into Myles at your shop. Good guy. Thanks, again, and I'll definitely be by in the future, as the need arises.

best,

thane

Thanks very much for the kind words! Glad to hear you're pleased with how everything turned out!

Rick

Posting up some SICK ACT clutch/install specials shortly! PM us for pricing and information!!! :)

Rick

Posting up some SICK ACT clutch/install specials shortly!
Just wanted to say that I really, really like my ACT clutch and streetlite flywheel. If these are on special, and someone is looking at a clutch replacement/upgrade, they should definitely look at this!

pm'ing

Just wanted to say that I really, really like my ACT clutch and streetlite flywheel. If these are on special, and someone is looking at a clutch replacement/upgrade, they should definitely look at this!

Thanks Karen! This setup, particularly on the 06 forward WRX and 05-08 LGT has really gained a large following lately!

pm'ing

PM'd back!

whats the Sat schedule look like over coming weeks? I might need a fender roll and possibly an alignment (if we increase camber)

whats the Sat schedule look like over coming weeks? I might need a fender roll and possibly an alignment (if we increase camber)

We actually do have some upcoming Saturdays available.. Give us a shout at the shop as soon as you get a chance and I'll get you scheduled in! :)

Rick

Finally starting to add some ACT Clutch Specials! More to come in the next few days!!!

One of our most popular packages for 06-Newer WRX and 05-08 Legacy GT w/ dual-mass flywheel:

ACT SB5-HDMM - ACT Heavy-Duty Modified Street Clutch with your choice of ACT Streetlite or Subaru OE 06-07 WRX Flywheel - $1199 Installed with your choice of fluids!!!

Thank you guys for the awesome service! I had IAG tint my windows and perform an alignment. They explained everything clearly and did all of the work very quickly - I hardly had time to check out their showroom. The alignment is spot on (no more pulling to the side.. thanks!) and the tint looks great. I'll definitely head back there the next time I need work done.

Thank you guys for the awesome service! I had IAG tint my windows and perform an alignment. They explained everything clearly and did all of the work very quickly - I hardly had time to check out their showroom. The alignment is spot on (no more pulling to the side.. thanks!) and the tint looks great. I'll definitely head back there the next time I need work done.

Thank you very much! We appreciate your business, and look forward to working with you in the future! :)

Rick

Just wanted to say thanks for diagnosing and fixing my loose Koni insert last week. It was nice to pass autocross tech inspection with flying colors again.

do you guys do brake rotor resurfacing?

Just wanted to say thanks for diagnosing and fixing my loose Koni insert last week. It was nice to pass autocross tech inspection with flying colors again.

No problem at all, glad everything worked out for you!

do you guys do brake rotor resurfacing?

We can offer that service. Front, rear or both? Shoot us a PM with your details, and I'll be happy to quote a price for you!

Regards,

Rick
IAG Performance
410-840-3555

how long are you guys going to run the clutch and flywheel special?

I just want to take this time to give IAG a BIG THANKS for all the work they've done to my car since last week. I went to get my 105k service and after the work was done, my power steering pump went bye bye. Needless to say, IAG decided to take my car back and make room in their busy schedule to fix it asap!

My car now drives super smooth and feels like i have 10,000 miles instead of 91,000 miles. Thumbs up to IAG!!!

Big thanks to IAG for doing my pre-dyno inspection in anticipation of the Jorge dyno day coming up in the next couple weeks. Everything was quick and painless, and my compression test came back great! Woot. :) Thanks guys. See you in a couple weeks!

Congrats JJ!

Congrats JJ!

+1 on that!

Congrats JJ!

+1 on that!


:confused:

Just want to give a hugh thanks to Rick and JJ for all their exceptional service I have received everytime I go to IAG. Especially for your help with swapping out my endlinks. The new Whiteline endlinks are great and I highly recommend them. Not many shops would have done what you guys did. I have been trying to avoid going up them because I can't spend any $$ on my car right now, but I am looking forward to the upcoming swap meet and open house.

Hi IAG, do you have this in stock?
http://www.iagperformance.com/shopping_cart/proddetail.php?prod=216BFWABO270PSI
or this:
http://www.iagperformance.com/shopping_cart/proddetail.php?prod=XS5201A
And this:
http://www.iagperformance.com/shopping_cart/proddetail.php?prod=216BFWAOP270PSI

Props to Nick and the guys at IAG, for helping me do something non-conventional. :D

http://img185.imageshack.us/img185/3817/image011000copy.jpg

Hi IAG, do you have this in stock?
http://www.iagperformance.com/shopping_cart/proddetail.php?prod=216BFWABO270PSI
YES
or this:
http://www.iagperformance.com/shopping_cart/proddetail.php?prod=XS5201A
NO
And this:
http://www.iagperformance.com/shopping_cart/proddetail.php?prod=216BFWAOP270PSI
YES



See Above!

Props to Nick and the guys at IAG, for helping me do something non-conventional. :D

http://img185.imageshack.us/img185/3817/image011000copy.jpg

different but i like it a lot

Rick! I need this:...?
http://www.iagperformance.com/shopping_cart/proddetail.php?prod=PSROPKIT
because this http://www.iagperformance.com/shopping_cart/proddetail.php?prod=PSOPSV wont fit in the galley plug.
Have it in stock?

Thanks Vinnyd. :)

Got what i need. Thanks guy, You're awesome!

Alright,

Just got the car back from the guys at IAG,

Should have been a simple turbo/EWG install and a Walbro Fuel-Pump, a good days worth of labor in and out right?

Wrong, idiot boy here decides he's going to get some AVCS lines that aren't what they're supposed to be and complicate the install...

So I get the call from JJ saying he's got to talk real quick (haha never good from your mechanic), and he tells me that the lines made them pull the intake manifold loose so they could fit...

Which added more time to the install and sent it into the next day, not a big deal...

Unless you are 30 minutes from home and without a car, IAG to the rescue!

Hooked me up with a ride back to my house and then got managed a ride back the next morning and all is well with the world...

So all my ducks are in a row for a tune next Saturday (if only I can live with this bloody 3500rpm limit!)

Thanks again guys,

Cheers,

~Mike

IAG, Rick, JJ... and everyone else...

I love you.

IAG, Rick, JJ... and everyone else...

I love you.

:lol:

Thanks! It was nice meeting you! Looking forward to hopefully seeing you again soon!

Rick

ttt for a great shop, They know so much and have a great staff. Ill be bringing the car down this fall again to get the tiens rebuilt and will have a nice surprise for the guys at IAG the next time in down.

ttt for a great shop, They know so much and have a great staff. Ill be bringing the car down this fall again to get the tiens rebuilt and will have a nice surprise for the guys at IAG the next time in down.

Thanks Gary! We like surprises around here.... :)

Rick

So i need to do my 30k service soon, and i am extremely nervous about the coolant flush and fill portion. I been reading threads about if you use something besides Subaru coolant you could possible void the warranty. There was also mention of the need to use Subaru Cooling System Conditioner as well. It seems that you guys use "Global coolant w/ 1 bottle of Motul MoCool" is that ok? I tried taking Advil but i still have a headache, please give me some good news. I dont dare to look into threads of transmission, differential and brake fluids. Once again IAG you guys are the best and i wont take my car anywhere else, but please help me out with some of my concerns.

Well i just got back from the ultimate customer service weekend. it took 3 staff members literally working around the clock(thanks to james, rick, JJ) and a few other who went home for a few minutes(jeff, fred, boris) to get my car on the dyno in time for jorge to tune( who was no slouch himself pulling and all nighter on friday as well, then flying from chicago to baltimore and tuning 7 cars in 1 day). This includes completely rebuilding the rotated kit for my car since the forester engine fitment is just slightly lower then the wrx so their pipes didn't fit. Also included fabbing up a wrx 5 speed crossmember to fit the new 6 speed since the guy i traded with didn't ship his even though i sent mine to him. Not that I have been to any other shop myself or recommend any other shop since I became a IAG customer but this level of customer service is one small reason why they are expanding their business now while others are shutting their doors and why they have a 100% customer rating

so in summary in 2 days: engine goes in, 6 speed get swapped in, custom forester specific 35r is fabbed, built, and installed

special thanks to ALL IAG staff members

oh and ill be back up sometime soon for my 09 sti brembo install

Add me to the 100% satisfied list. Rick, JJ and Jorge are the best. My pre-tune and dyno tune went great!

Everything was great for me as well. Thanks Rick, JJ, and Jorge!

PS- Why doesn't someone start a thread in Mid-A so we can post up results/comments/such? Would be a great way to get the word out there from all of the satisfied customers regarding their tune! :)

Thanks everyone for the positive comments! :)

Rick

Rick,

you have good deal for tire mount and balance?

how much for a meth kit install? looking at purchasing perrins meth kit. any # of days the car would need to stay over. pm me with a price and some info.thanx,mike

Rick,

you have good deal for tire mount and balance?

Tires purchased from IAG are $15 to Mount & Balance (each) or $20 to Dismount current tires, Mount new tires & Balance (each). Of course, all mounting and balancing is performed on our Hunter Auto 34 (almost completely touch-less system) and our Hunter 9700 Road Force Balancing machine (see below :) )

http://www.iagperformance.com/images/service/wheel_tire/hunter/image_04_635.jpg


how much for a meth kit install? looking at purchasing perrins meth kit. any # of days the car would need to stay over. pm me with a price and some info.thanx,mike

PM Sent!

Rick

^ does it mean i dont have to worry on my rims?...lol

80$, If my arithmitic is right...then ill make an appointment.

^ does it mean i dont have to worry on my rims?...lol

80$, If my arithmitic is right...then ill make an appointment.

Yes sir! It would be $80 to dismount, mount & balance all four tires... Give us a shout to set up an appointment when you're ready! :)

Rick
IAG Performance
410-840-3555

MAIC PLEASE TAKE YOUR SUBY TO IAG FOR ALL OF ITS NEEDS. I recently had my 30k, new tires mounted and balance, sway-bars and endlinks, steering rack bushing, allignment, and a heat shield installed. These guys provided excellent technical support as well as service. Everything was done with the great attention to detail. I drove 2.5 hours just to have my car worked on by them. It was worth every penny and the drive home was even better with all my new parts. SPECIAL THANKS TO RICK AND JJ, GREAT GUYS. Hope to see you at the shop soon.

How much do you guys charge for corner balancing?

had my fenders rolled this past saturday and had a great time. My gf said the clean bathroom was 100% worth the drive. :lol:

thanks for showing my gf and myself around the shop and even recommending I not spend as much! I like saving money! I'll be back up in the near future with some other work! A++

How much do you guys charge for corner balancing?

Cornerbalance/alignment is $199

MAIC PLEASE TAKE YOUR SUBY TO IAG FOR ALL OF ITS NEEDS. I recently had my 30k, new tires mounted and balance, sway-bars and endlinks, steering rack bushing, allignment, and a heat shield installed. These guys provided excellent technical support as well as service. Everything was done with the great attention to detail. I drove 2.5 hours just to have my car worked on by them. It was worth every penny and the drive home was even better with all my new parts. SPECIAL THANKS TO RICK AND JJ, GREAT GUYS. Hope to see you at the shop soon.

had my fenders rolled this past saturday and had a great time. My gf said the clean bathroom was 100% worth the drive. :lol:

thanks for showing my gf and myself around the shop and even recommending I not spend as much! I like saving money! I'll be back up in the near future with some other work! A++

Thanks to both of you for the kind words! We appreciate your business, and look forward to working with you in the future!

Kind Regards,

Rick
IAG Performance

How much do you guys charge for corner balancing?


Sorry, just realized you were asking about corner balance only.... That would be $125.

Rick or JJ,
I was looking on the site at the Rotas. Im going to wait until I get some more cash together. But anyway, some of the rims im looking into need fender rolling and what not (which i also want haha). There any deal if I were to get both done at same time (same day)?

Thanks,
Bobby

I dunno if i'll do the corner balancing. I want to buy something for the car, but i dunno what to get. Maybe perrin inlet hose?? Recommend me something between $200-$350!

Rick or JJ,
I was looking on the site at the Rotas. Im going to wait until I get some more cash together. But anyway, some of the rims im looking into need fender rolling and what not (which i also want haha). There any deal if I were to get both done at same time (same day)?

Thanks,
Bobby

Sure, I can work up a package price for you! Give me a call some time and let me know what wheels, etc. you're interested in, and I can work up an estimate! :)

I dunno if i'll do the corner balancing. I want to buy something for the car, but i dunno what to get. Maybe perrin inlet hose?? Recommend me something between $200-$350!

There are a ton of options... Give me a call at the shop some time... I'd like to find out everything that you already have, so that maybe we can go over some options... Definitely want to make sure you get the most for your money!

Rick

Sure, I can work up a package price for you! Give me a call some time and let me know what wheels, etc. you're interested in, and I can work up an estimate! :)



There are a ton of options... Give me a call at the shop some time... I'd like to find out everything that you already have, so that maybe we can go over some options... Definitely want to make sure you get the most for your money!

Rick


Ok Rick, you should have a call tomorrow. Im not sure when ill have money (but should be starting union job on monday)

Yes sir! It would be $80 to dismount, mount & balance all four tires... Give us a shout to set up an appointment when you're ready! :)

Rick
IAG Performance
410-840-3555

Ok, guys thanks for the Great deal and service...Very satisfied customer!

Thank you for all the help this year, IAG. Without it, I wouldn't be the newest ESPL National Champion. :) :D

Thank you for all the help this year, IAG. Without it, I wouldn't be the newest ESPL National Champion. :) :D

Holy cow, I looked over this! Congrats Karen!!!! :banana:

Rick

Hey... Look what I found! :)

Rick

http://www.iagperformance.com/images/sponsored_cars/karen/image_10_635.jpg

Hey... Look what I found! :)

http://www.iagperformance.com/images/sponsored_cars/karen/image_10_635.jpg
:lol: I've got some from the 30brazillian sq.miles of concrete that is Lincoln, NE. You can seriously see the curvature of the Earth in some of them. I just need to get some uploaded and/or wait for the CD to arrive. In the meantime, here's one that Pat or one of the DC guys took :
http://farm4.static.flickr.com/3475/3917790492_cb78edd224.jpg

Need to chat with you about another oil change after the 2500 mile round trip too, and the passenger front axle seal. If I find a spare minute tomorrow, I'll likely give you a ring to try to set something up.

Karen

Call about ACT Clutch packages today! ACT has been insanely popular for installs lately! :)



http://www.iagperformance.com/images/service/transmission/clutch/image_01_1000.jpg

how long does it take to get my fender rolled and pulled? 1 1/2 hour to drive there LOL

how long does it take to get my fender rolled and pulled? 1 1/2 hour to drive there LOL

It would really depend on exactly how much fender work is required. Shoot us a PM with what kind of wheel/tire/suspension package you are running, or feel free to call at the shop any time to discuss! :)

Regards,

Rick
IAG Performance
410-840-3555

Great job guys on my stage 2 brake upgrade. The difference is amazing and is everything I'd hoped it to be: shorter stopping distance & firmer pedal feel. I'll be back in late Jan or early Feb for the 60K.

Michael

Rick, JJ:

thanks for the great work done on my car (02 PSM WRX): 105K service, stage 2 brakes, and the TD04 replacement.

the car is running great and I feel much better about pushing it hard now. :banana:

For the time that "Speedy" was at the shop, I thought you had all repo'd her........LOL.

again thanks.

Courtney

Great job guys on my stage 2 brake upgrade. The difference is amazing and is everything I'd hoped it to be: shorter stopping distance & firmer pedal feel. I'll be back in late Jan or early Feb for the 60K.

Michael

Rick, JJ:

thanks for the great work done on my car (02 PSM WRX): 105K service, stage 2 brakes, and the TD04 replacement.

the car is running great and I feel much better about pushing it hard now. :banana:

For the time that "Speedy" was at the shop, I thought you had all repo'd her........LOL.

again thanks.

Courtney

Michael and Courtney,

Thanks to both of you for the kind words! You were both a pleasure to deal with, and we greatly appreciate your business!

Regards,

Rick

Awesome ACT Deal!

ACT HDSS STI Heavy Duty Street Clutch - ACT Heavy-Duty Modified Street Clutch with resurfaced flywheel for 04-09 STI 6-Speed - $1199 Installed with your choice of fluids!!! - Limited Time Only!!!

how long does it take to get my fender rolled and pulled? 1 1/2 hour to drive there LOL

only took an hour for us i believe. drive through rockville and up the back way. its a great drive when its nice out :D

only took an hour for us i believe. drive through rockville and up the back way. its a great drive when its nice out :D

Yeah there are a lot of factors that go into fender rolling turnaround time, obviously with limitless wheel/tire combinations, etc. On an average set up, you can expect 1-2 hours, and more extreme setups, a little more. Most of that time is spent in preparation, to take every precaution possible to help prevent paint cracking, etc.

There are definitely a variety of really nice, scenic drives to get up to our shop from the surrounding areas... Some day when I have a little bit of extra time, I'd like to get a few of those routes together... Seems like a lot of our customers coming up really enjoy taking the more back-road/scenic drives to get here!

Rick

i miss IAG.... :(

thanks for a very thorough "60k" ;)
i guess when you have the entire driveline out at 56k they 60k is a little quicker
rick you car feels awesome

What kind of deal do you have on breaks now? i am in need of front and rear pads and rotors. Wouldnt be till a few weeks though, im going to vegas on Sat

What kind of deal do you have on breaks now? i am in need of front and rear pads and rotors. Wouldnt be till a few weeks though, im going to vegas on Sat

We are running our Stage 2 Package with rotors, pads, lines, fluids, labor for $949 for WRX (see Post #1) - We can do DBA or Racing Brake rotors, Hawk Pads, Techna-fit lines, and Ate or Motul fluids. Give me at the shop if you have any questions. We are booked out a few weeks right now, so if you'd like to book an appointment, give me buzz in advance! :)

thanks for a very thorough "60k" ;)
i guess when you have the entire driveline out at 56k they 60k is a little quicker
rick you car feels awesome

Thanks, Vince, glad you were happy with the 60K :lol:

I must say, your car feels amazing... Glad I finally got to take a ride!

i miss IAG.... :(

How's Aiken, SC? That's not too far off from Charleston, correct?

Doesn't Subaru recommend against resurfacing flywheels?

Yeah there are a lot of factors that go into fender rolling turnaround time, obviously with limitless wheel/tire combinations, etc. On an average set up, you can expect 1-2 hours, and more extreme setups, a little more. Most of that time is spent in preparation, to take every precaution possible to help prevent paint cracking, etc.

There are definitely a variety of really nice, scenic drives to get up to our shop from the surrounding areas... Some day when I have a little bit of extra time, I'd like to get a few of those routes together... Seems like a lot of our customers coming up really enjoy taking the more back-road/scenic drives to get here!

Rick

It actually was nice after you get past the lights around rockville and such. Hopefully heading back up in a week or so for some more work.

Just wnted to thank JJ and the guys at IAG for helping me out. I have a blown Progress coilover on my wagon and they got me the stuff i needed to keep me goin while they get sent away to get re-valved. Thanks for being here when when ppl are in pinch!!! You guys are great!!!!

Thanks,

Fred

Just wnted to thank JJ and the guys at IAG for helping me out. I have a blown Progress coilover on my wagon and they got me the stuff i needed to keep me goin while they get sent away to get re-valved. Thanks for being here when when ppl are in pinch!!! You guys are great!!!!

Thanks,

Fred

Thanks for the kind words Fred! :)

finally the day has come. lookin forward to getting my new struts installed tomorrow!

You wont regret it. I'm trying to save up for some coilovers from IAG.

Bringing this thread back from the dead for the new year! :)

I will probably call you guys sometime this week, but I was wondering if you know offhand when you would be able to fit me in to get my 60K service done?

finally the day has come. lookin forward to getting my new struts installed tomorrow!

by the way, the new struts and springs feel great! car handles like a beast.

I will probably call you guys sometime this week, but I was wondering if you know offhand when you would be able to fit me in to get my 60K service done?

PM Sent!

by the way, the new struts and springs feel great! car handles like a beast.

PM replied :)


Rick

is the 60k service 499.00 for an o6 wrx?

is the 60k service 499.00 for an o6 wrx?

Yes, that is correct! Please shoot us a PM if you have any other questions, or feel free to call here at the shop if you would like to schedule some time! :)

Regards,

Rick
IAG Performance
410-840-3555

pm sent on parts!

pm sent on parts!

Order processed! Thanks for your business! :)

thanks alot for all the help!
you guys have top-notch customer service,by far best i have delt with.
cant wait to get everything in,be expecting another big order from me within the next week or two.

Big thanks to Rick for selling me 09 Sti turbo for a good deal! and thanks for giving me to advice on installation ! Everything is smooths so far!

Quick question:

Is the "Sway-Bar/end-link Install - $79" is that for both or price for each?

Boy do I have a list for you guys :devil:

...When my "bleeping" coilovers get in!!! :furious:

I will hopefully get some shipping information on Wednesday and hopefully we can set something up for early Monday (have class at 7 pm in Richmond :eek:). I will be calling you with more detailed information/questions.

As always, you guys are great! Best costumer service EVARRR!!!

-Garrett

Man feels like forever since i have been up there..... going to have to buy more parts soon Rick!

Rick,got my packages today,everything looks great!
I emailed you again about the turbo setup im looking at.
Thanks

thanks alot for all the help!
you guys have top-notch customer service,by far best i have delt with.
cant wait to get everything in,be expecting another big order from me within the next week or two.

Jesse,

You're welcome! We look forward to hearing from you again as always!

Big thanks to Rick for selling me 09 Sti turbo for a good deal! and thanks for giving me to advice on installation ! Everything is smooths so far!

Chris,

No problem. We will see you tomorrow.

Boy do I have a list for you guys :devil:

...When my "bleeping" coilovers get in!!! :furious:

I will hopefully get some shipping information on Wednesday and hopefully we can set something up for early Monday (have class at 7 pm in Richmond :eek:). I will be calling you with more detailed information/questions.

As always, you guys are great! Best costumer service EVARRR!!!

-Garrett

Thanks as always Garrett! We'll see you Monday! :)

Man feels like forever since i have been up there..... going to have to buy more parts soon Rick!

Sam,

Good to hear from you yesterday. I sent an email for the 52mm-60mm conversion sleeves. Get back with me when you can and we'll get them shipped right out!

Rick,got my packages today,everything looks great!
I emailed you again about the turbo setup im looking at.
Thanks

Email returned about the turbo, etc. I'll look forward to hearing back!


Thanks everyone for the kind words and continued business!

Rick
IAG Performance

i stopped in today with a few guys,and i must say for the first time being there you guys have a great shop..looking forward to coming back.

PM'ed!

i stopped in today with a few guys,and i must say for the first time being there you guys have a great shop..looking forward to coming back.

Thanks for coming down! Glad you guys had a good time!

PM'ed!

PM'd back! :)

Rick

Thanks for everything you guys! The car rides like a dream now! :D I don't have to worry about hitting bumps or going up inclines anymore.. and that sunstrip with the IAG representation windshield sticker is beast. I feel like i'm driving a race car :lol:

Thanks for everything you guys! The car rides like a dream now! :D I don't have to worry about hitting bumps or going up inclines anymore.. and that sunstrip with the IAG representation windshield sticker is beast. I feel like i'm driving a race car :lol:

Garrett,

Good to see you as always, and thanks for representin'! :)

We'll talk to you soon!

Rick

Great ACT/Install packages available upon request! We've had several inquiries into their 6-puck setups recently... PM for a smokin' deal! :)

Rick

Hey IAG,

I was wondering if you had the following items in stock:

https://www.iagperformance.com/shopping_cart/proddetail.php?prod=KB-011-RD

https://www.iagperformance.com/shopping_cart/proddetail.php?prod=S101YELLOW

Thanks,
David

Hey IAG,

I was wondering if you had the following items in stock:

https://www.iagperformance.com/shopping_cart/proddetail.php?prod=KB-011-RD

https://www.iagperformance.com/shopping_cart/proddetail.php?prod=S101YELLOW

Thanks,
David

Both in stock. PM sent!

Rick

Great ACT/Install packages available upon request! We've had several inquiries into their 6-puck setups recently... PM for a smokin' deal! :)
I'm still loving the Streetlite flywheel and heavy duty ACT clutch -- even in the snow-of-the-century driving I've been doing lately! The car is still very streetable, even when the streets are snow-covered! :banana:

(I'll have to tell you my "snowed-out" story next time I stop by ;) )

Karen

Thanks to Rick, JJ and the entire IAG crew. Stayed open late (to get setup for tuning tomorrow) but allowed me to drive up and pick my V2 AccessPort up and put a stage 2 tune on it. Thanks guys :D

Gotta love the IAG crew. Will be in soon to get some rims, tires and other goodies. Thank You Uncle Sam!!

Bump for IAG :disco:

I'm here getting an oil change (yes I don't change my own oil since it's cold outside!)

Thanks to IAG crew for 90K service of my Foz. I will see you on Monday 8th evening for PDI of the STI.

Bump for IAG :disco:

I'm here getting an oil change (yes I don't change my own oil since it's cold outside!)

hey i don't change my oil cuz i don't have a garage :(

laying on the dirty streets of baltimore is not a good idea.

hey i don't change my oil cuz i don't have a garage :(

laying on the dirty streets of baltimore is not a good idea.

I don't have a garage either. I've done some car stuff in front of my house before and my buddy's call me crazy... I guess with people driving 35MPH (speed limit) within a few feet from me is kinda crazy :lol:

Yea, you're nuts for doing that..

I need to bring the WRX up for some pre-autocross-season stuff. I'll be calling Monday or Tuesday, Rick. Gotta get that Sparco put in, maybe get some stainless steel brake lines, and check the alignment after the lovely minefields that developed since the snowmageddons. :)

I need to bring the WRX up for some pre-autocross-season stuff. I'll be calling Monday or Tuesday, Rick. Gotta get that Sparco put in, maybe get some stainless steel brake lines, and check the alignment after the lovely minefields that developed since the snowmageddons. :)

Watch those speed camera's ;)

Oh and Rick was NOT in there Saturday when I came in! I was sad :sadbanana: but I got to see JJ :p

why would you be sad not to see rick...:lol:

I see you do tailight film installation, do you have these films on site or would I need to purchase one for you to put on? Would need a red tail with reverse light cutout for a 2010 STi. Also could you PM with prices of this and window tinting 20%ish all around. Thanks.

hey IAG, which Muteki Lugs do you have in stock right now? The lugs I have are rusting and ugly from the winter/salt and I'm thinking about getting others when I change wheels over. Thanks.

just wanted to say thanks for the RA mudflaps... got 'em today, and super happy with how fast I received them from you guys... all the way from the east coast, all the way to me in SoCal... took just 3 days shipped... AWESOME!!! :disco::banana::taco:

PM sent regarding 96 SVX

PM sent about my Saabaru

All PM's have been replied, and I think I've responded to everyone's questions! If not, give us a call 410-840-3555 or shoot us an email or PM any time! Thanks to everyone! :)

Rick