Hey everyone,

We've closed an exclusive distribution agreement with PDE. There are lots of boring details (PDE Press Release Here (http://forums.nasioc.com/forums/showthread.php?t=789373)), but one good result:

SERIOUS PRICE REDUCTIONS

We've got a lot of stock on everything. Pickup and install only for now. We'll be shipping in a few weeks.

http://pcomm1.securesites.net/secure/harmanmotive/clientuploads/directory/parts/pde-1005.jpg
- PDE Catted Downpipe WRX/STI - $559 (was $699)

http://pcomm1.securesites.net/secure/harmanmotive/clientuploads/directory/parts/pde-1002.jpg
- PDE Catless Downpipe WRX/STI - $295 (was $399)

http://pcomm1.securesites.net/secure/harmanmotive/clientuploads/directory/parts/pde-1001.jpg
- PDE Solid Uppipe WRX/STI/Legacy GT - $159 (was $209)

http://pcomm1.securesites.net/secure/harmanmotive/clientuploads/directory/parts/pde-1003.jpg
- PDE Flex Uppipe WRX/STI/Legacy GT - $229 (was $279)

http://pcomm1.securesites.net/secure/harmanmotive/clientuploads/directory/parts/pde-1010.jpg
- PDE Front Camber Plates WRX/STI/Legacy GT - $259 (was $425)

http://pcomm1.securesites.net/secure/harmanmotive/clientuploads/directory/parts/pde-1006.jpg
- PDE Billet Petals WRX - $225 (was $399)

Come and get 'em. We'll be offering some silly install specials starting next week too, so stay tuned!


Thanks,

Ian A.
Harman Motive

I'll be by today for the catless uppipe and camber plates.

does pde dp have flat flange or donut flange?

does pde dp have flat flange or donut flange?

It has a donut flange. It will also bolt to any aftermarket catback (2.5" or 3") with a flat gasket.

Regards,

Dan

yes, but it's not optimal and it may leak. thanks for the info.

hmmm.... radiator or camber plates? radiator or pedals?

hard to resist spending $$$ with those prices.

hmmm.... radiator or camber plates? radiator or pedals?

hard to resist spending $$$ with those prices.
both :devil:

will the pedals work in an RS (fora rally car)

will the pedals work in an RS (fora rally car)

We haven't tried it, but I'd be shocked if it didn't fit (it doesn't fit DBW models though).

If you want to try it out, you can return the set if it doesn't fit.

Regards,

Dan

Fitment for AGX?

Fitment for AGX?

Fits AGX.

It will fit any strut/coilover that allows the use of the stock topmount.

Regards,

Dan

Any camber/caster plates for GC/GF/GM?

They should fit the GC/GF/GM chassis cars as well. These are stock replacements. Since a GD suspension will swap to a GC, they should work fine.

Regards,

Dan

I sent you an e-mail last night!

bump!

price on Legacy catless DP?

price on Legacy catless DP?

We're building the first batch run of Legacy Cat-less Downpipes right now, they'll be ready in approx three weeks.
I'm trying to hold the price to under $300, but it'll be close and might go a little over. I need to complete this first batch run before we can release a 100% accurate MSRP.
Fits manual transmission cars only for now, auto trans will be later this year.
We'll be releasing a Catted Downpipe for the Legacy at the same time, followed by a full Legacy cat-back (we've already completed prototyping and testing).

Regards,

Ian Stewart.
PDE Inc.
www.pde-usa.com

Hey Ian,

Thanks for the camber plates and the phone call to confirm shipping. Everything came in on time. Any chance you guys will have written instructions in the future? That would be a big hit now that your prices are so good. Might save your tech line some time.

Cheers, Inferno

P.S. I never could get Harman Motive to take my order (PMed, emailed, talked to them on the phone three times but they would not take my order: "call back in a few days and we will get the info then." Very strange for someone trying to sell parts...)

Inferno STi,

We do greatly apologize for the inconvenience concerning this situation. The fact of the matter was that we feel uncomfortable taking orders and taking money on shipping orders, until the products are physically in our warehouse. This system avoids potential dissapointment on when things are going to ship... and refunds when certain expectations are not met. We have had them in stock for about a week now, and are currently taking orders!

Again, apologies for the inconvenience...which is what we were actually trying to avoid in the first place:)

Ian A.
Sales Manager
Harman Motive, Inc.

We're building the first batch run of Legacy Cat-less Downpipes right now, they'll be ready in approx three weeks.
I'm trying to hold the price to under $300, but it'll be close and might go a little over. I need to complete this first batch run before we can release a 100% accurate MSRP.
Fits manual transmission cars only for now, auto trans will be later this year.
We'll be releasing a Catted Downpipe for the Legacy at the same time, followed by a full Legacy cat-back (we've already completed prototyping and testing).

Regards,

Ian Stewart.
PDE Inc.
www.pde-usa.com (http://www.pde-usa.com)

Thank you for the quick response, I might wait until you release this DP then... I'm in the market for one right now...

Do the camber plates allow you to adjust caster also? How much for installation on an 03 sedan with KYB AGX struts?

Do the camber plates allow you to adjust caster also? How much for installation on an 03 sedan with KYB AGX struts?

They sure do. You simply move the upper studs to the alternate threaded holes - this rotates the whole assembly. (See Pic)

https://pcomm1.securesites.net/secure/harmanmotive/clientuploads/forums/pde1010-caster1.jpg

Sent you a PM.

Regards,

Dan

We're building the first batch run of Legacy Cat-less Downpipes right now, they'll be ready in approx three weeks.
I'm trying to hold the price to under $300, but it'll be close and might go a little over. I need to complete this first batch run before we can release a 100% accurate MSRP.
Fits manual transmission cars only for now, auto trans will be later this year.
We'll be releasing a Catted Downpipe for the Legacy at the same time, followed by a full Legacy cat-back (we've already completed prototyping and testing).

Regards,

Ian Stewart.
PDE Inc.
www.pde-usa.com
Update on the catted DPs?

Update on the catted DPs?

We're still in manufacturing - had a few issues with the stainless steel tube supplier sending us tube with a wall thickness under spec, and consequently the internal bend mandrel was undersize for the tube...

We're working on it and moving forward. Apologies for the delay, but sometimes these issues are out of our control. We're really close though, and we should be easily shipping Legacy Downpipes by the end of the month.

Thanks for understanding...

Regards,

Ian Stewart.
PDE inc.
www.pde-usa.com

HarmanMotive,

I,ll take some of those Camber Plates if they a GC8. Have Pedro Get ready to install them for me.

Thanks,
Jesse (Turbo-rs)

what's the price on a dp install??