///For Sale///


-FP Green 2.4 inch inlet used for about 25,000 miles-$900

We are now back to being fully staffed in the shop, and are scheduling service appointments for quick turn around.

With the economy and fuel prices the way they are, we’ve cut some prices back to try and help with your Subaru’s needs. Although this list is based on the WRX/STI, most prices will cover all of the Subaru line…..and some other makes. Take a look!

Andrewtech T-belt special!!
For the rest of '08 we will be doing T-belt replacements on '02-'06 WRX/STI for $300 patrs and labor! Take advantage of this if your comming due for this service! Call if you like to verify if your car qualifies (ie-you don't have a v-mount.....).

Andrewtech oil change
Change engine oil, filter, and install new drain plug gasket, set tire pressure, and top off fluids.
Complimentary vehicle inspection
($42.38 Conventional oil) ($75.38 Motul synthetic)*


Andrewtech 7500 mile service
Change engine oil, filter, and install new drain plug gasket, set tire pressure, rotate tires, and top off fluids.
Subaru specified vehicle inspection
($94.32 Conventional oil) ($127.32 Motul synthetic)*


Andrewtech 15,000 mile service
Change engine oil, filter, and install new drain plug gasket, set tire pressure, rotate tires, clean/service or replace air filter, and top off fluids.
Subaru specified vehicle inspection
($129.81 Conventional oil) ($172.81 Motul synthetic)*


Andrewtech 30,000 mile service
Change engine oil, filter, and install new drain plug gasket, set tire pressure, rotate tires, clean/service or replace air filter, replace fuel filter (if applicable), brake fluid flush with Motul fluid, change engine coolant, and top off fluids.
Subaru specified vehicle inspection
($333.70 Conventional oil) ($386.70 Motul synthetic)*


Andrewtech 60,000 mile service
Change engine oil, filter, and install new drain plug gasket, set tire pressure, rotate tires, clean/service or replace air filter, replace fuel filter (if applicable), brake fluid flush with Motul fluid, change engine coolant, replace spark plugs, and top off fluids.
Subaru specified vehicle inspection
($434.40 Conventional oil) ($477.40 Motul synthetic)*

*Prices quoted may vary depening on vehicle year, make and model. Pricing subject to change at any time.

Andrewtech in house alignments-
Four Wheel Alignments to Factory Spec - $89.99*
*Pricing may not include alignments on vehicles with some aftermarket suspension systems, as these may require more time to align. Pricing does not include the installation and/or adjustment of rear camber bolts to reach desired specifications.
Vehicle Corner Weighing - $40 (includes recording current total vehicle weight and corner weights; does not include corner balancing)
Vehicle Corner Balancing available - Pricing varies.

Always remember, our technicians are factory trained and certified technicians.

Please mention this ad to recieve special pricing.

As a TurboXS Wholesale Distributor, we can meet or beat just about any price on TurboXS Products. Call and see for yourself! UTEC's, Exhausts, Front Mounts, everything in their catalog!
Check out the new UTEC Delta v2.0!
http://www.turboxs.com/images/Delta-Evolution-web.jpg

We are always running clutches for an unbeatable price Pm us for pricing on whatever clutch you need!



http://i73.photobucket.com/albums/i221/Andrewtech/General-655x84-Web-Banner-B.gif (http://www.andrewtechautomotive.com)

Andrew
Andrewtech Automotive

PM'd you

What you ought to sell is a catback for we poor RS/L/TS/i folks. :D

JDM angles.... ick... never liked those. Fugly, IMO.

-Chris

I saw the kits when Phil was taking pics....the Invidia stuff was pretty hot looking! I'd love to hear what the exhaust sounds like installed.

Does Invidia make a JDM length downpipe? Do you have any?

Brent, good question. We just have the US stuff in stock for the STi/WRX. InvidiaUSA does not have the JDM length downpipes available to the US market.

Also to note, these are the divorced wastegate style of downpipe.

http://www.invidia-usa.com/_Images/632584928837343750_0.jpg

Phil
Andrewtech Automotive

Phil, I assume the Invidia cat-back will work with a Perrin down pipe? PM me the cost of just the cat-back. I'm interested in the N1 race version.

We are actually only selling these as a complete kit.

I probably should have mentioned that these kits ARE the N1 race system.

Phil (or other Andrewtecher), I'm looking for a cheapo, used cat pipe for my TurboXS system. Got one you're willing to part with?

My car stinks ever since I drove back from north carolina with no spark in 2 of my cylinders. Pretty sure my cat is a goner since the car is otherwise running fine and my AFRs are fine.

Updated!
Andrew

Thanks for a great deal on the Accessport!!! Can't wait to get it.

Thanks for a great deal on the Accessport!!! Can't wait to get it.
Your welcome. It did ship yesterday.
Updated list.
Andrew

Updated list again.
Andrew

Updated list again.
Andrew
Wow that was quick..... you only have one Accessport left!!!!!

Somebody grab the last one up!!!!!

I heard that the accessports are selling at a rediculous price .... only one left!!!! wow!

wish you had an 03

Can you PM me a price for the TBE with a high flow cat welded in?

I want that last Accessport, but am having difficulty with another vendor.

Can you PM me a price for the TBE with a high flow cat welded in?


LMK if you buy it. I wanna hear that thing! They look so nice. Supposedly they fit really well. I guess Invidia isn't as high profile as some of the other manufacturers...but the build quality looked sweet. If you come up to buy and install it at Andrewtech, I'll meet you up there. Maybe grab a bite to eat (wings and beer)?

Sure thing ... purchase must be approved by the CFO (my wife). I need to call Andrewtech tomorrow to get a price.

Sure thing ... purchase must be approved by the CFO (my wife). I need to call Andrewtech tomorrow to get a price.
Please do. I'm thinking we might have to mount the pipe to accuratly weld the cat in place. I wouldnt want to send you a pipe you couldnt use!
Andrew

Please do. I'm thinking we might have to mount the pipe to accuratly weld the cat in place. I wouldnt want to send you a pipe you couldnt use!
Andrew

Yep, I agree. I didn't think that you'd eyeball it and just ship something to me :) I'll try to give you guys a call later this afternoon.

I want that last Accessport, but am having difficulty with another vendor.


YAY! It is mine!

Yep, I agree. I didn't think that you'd eyeball it and just ship something to me :) I'll try to give you guys a call later this afternoon.

hey Dave you gonna go SAT at Ripken?


James

Updated list again!
Andrew

Thanks for the Accessport, I'll hopefully have it installed very soon.

i need a AP. I pmd you but you never responded :(

Nice work you guys did on my brakes, thanks! Saved me a cold day outside in the driveway. :)

i need a AP. I pmd you but you never responded :(

I called to see if they still had some stocked and placed my order; these guys seem pretty busy and I'm sure phone is the best way to get a hold of them.

I called to see if they still had some stocked and placed my order; these guys seem pretty busy and I'm sure phone is the best way to get a hold of them.

Thanks! I will try to day.

Thanks, for the invidia!

The invidia exhausts are the top of the line, build quality, fitment, everything. The invidias fit like a glove on the car, I love mine. Invidia also produces some of the best tones i've heard.

I was thinking about the Carbon Ti but Andrew talked me out of it so I went with the invidia which comes with the free blumpkin from james.

I came by to check the part out and they offered to install it early on a friday afternoon instead of next thursday which was awesome. I felt bad being there on friday afternoon because i know how it is getting work late on fridays it SUCKS but they offered which was great!

And I got a group hug before i left ;)


C/N: Guys at Andrewtech are great, Invidia exhaust is great.

Thanks Rod. That G200 Invidia is sick. Not to many people have ever seen this exhaust in person. Show the Mid-A and spread the love.

As for the Blumpkin I do what i must to keep My job.LOL


James

Blumpkin=Insidejoke=nevermind

James, what can you do for me in the way of a JDM length bellmouth 3" catless downpipe? Shoot me a PM. Thanks.

Brent

do you have any catch cans in stock?

do you have any catch cans in stock?
PM sent.
Andrew

Added new items.
Andrew

^ Do you still have the 04 Accessport?

^ Do you still have the 04 Accessport?
Only one left.....
Andrew

^ nope...dibs! I'll swing by and pick it up this afternoon. Do you take 4th party checks w/ one form of ID that isn't close to me (without a photo, too)?

^ nope...dibs! I'll swing by and pick it up this afternoon. Do you take 4th party checks w/ one form of ID that isn't close to me (without a photo, too)?
And it's gone! We still have loads of utecs at the hook up price! :)
Andrew

again many thanks!
see you next monday for ppg install
raj

pmd ya --- m u s t g e t e n g i n e mgmt........ der........stall.....stall....... stall.......... go.....

pmd ya --- m u s t g e t e n g i n e mgmt........ der........stall.....stall....... stall.......... go.....
You need one of these!
Andrew

http://i73.photobucket.com/albums/i221/Andrewtech/6spd010.jpg

You need one of these!
Andrew

http://i73.photobucket.com/albums/i221/Andrewtech/6spd010.jpg
Man that looks sick!!!!!!!!

I just got some cool new goodies from Subaru!

The SPT High-Flow intakes are here! This thing is beautiful! Mandrel bent intake that comes with a high-flow Subaru cone filter (even the filter has it's own part number!). The intake uses a silicone connector and T-bolt clamps to hold it all together. Add to that a really nice mounting setup that reduces vibration induced noise. The intakes are gray powder coat with a raised SPT logo. The absolute best part is that this is a 50-state emissions legal accessory! The MSRP is $209.95. We have them ready to go for $170.00!

We also have a Cosworth motor for sale. It has never been started, just put on an engine stand for pics.

built off a brand new 05 long block core from subaru.
All New from Subaru Stock Long-Block (2005 2.5L STI MOTOR)
Darton Sleeves/Liners For 100mm Pistons
79mm Billet Cosworth Crankshaft
High performance Main and Big End Bearing
Cometic Head Gasket
Xtra Heavy Duty Forged Connecting Rods (Cosworth Spec) With ARP Heavy Duty Bolts
Cosworth Spec EJ25 Light Weight Forged 100mm Pistons
Cosworth Spec H.P. Rings
Cosworth CNC Ported Big Valve-Max Flow Race Cylinder Heads
ARP Heavy Duty 11mm Head Studs
272/262 June Cams and June Adj. Cam Sprockets
Power Enterprise heavy duty cam/timing belt
1mm oversized Stainless Steel intake valves
1mm oversized Inconel-high temp exhaust valves
Hi Rev (Max 10,500rpm) Valve Spring Package
Billet timing belt tensioner
8.25 to 1 Compression
Balanced and Blue Printed
asking $14,500.00
have bill from cosworth paid $18,400.00+shipping

Pick the right turbo, attach it to this motor, and 750+ awhp is at your finger tips!

Here are a few pictures of the motor (click for biiiiig pics):

http://www.nezfotnemom.com/up/cosworthbillettcranksmall.JPG (http://www.nezfotnemom.com/up/cosworthbillettcrank.JPG)
http://www.nezfotnemom.com/up/cosworth2small.JPG (http://www.nezfotnemom.com/up/cosworth2.JPG)

That engine is RIDICULOUS.

Uh...what else was I going to say...oh, right! Hey do you have the heat shields for the SPT intakes?

I can GET the heat shields. PM us.

Phil
Andrewtech Automotive

Well, I just got a heat shield for the SPT intake IN STOCK. I've got one intake left!

Phil
Andrewtech Automotive

absolutley beutiful intake, i will have one in a week or two

13k for the motor? it says the rods are cosworth spec, does that mean they are cosworth?

They are Cosworth Rods, and the price is actually $14,500.

can you guys get SPT catbacks?

Of course I can!

well, that intake is mine now and it rocksors

AndrewTech,

Sort of unrelated, but please check your PMs. :) Sending you one now.

-Chris

AndrewTech,

Sort of unrelated, but please check your PMs. :) Sending you one now.

-Chris
ditto

All PM's have been replied to!

First post updated! New inventory IN STOCK!

Updated first post!

We now have RWD conversion kits for the 5 and 6 speed manual transmissions IN STOCK and ready to rock!

Impress your friends! Wow your neighbors! Upset American car owners! Annoy the police! Rear Wheel Drive, your ticket to fun.

Updated the first post! New TurboXS Products ON THE SHELF!

willl be giving you guys a call to set up an alignment appointment this weekend. what are your shop hours? theyre not listed on your website.

willl be giving you guys a call to set up an alignment appointment this weekend. what are your shop hours? theyre not listed on your website.
Great! Give a call M-F 8-6. What kind of setup are you thinking?
Andrew

Thanks for the Exedy clutch and flywheel! Great prices and awesome install. I'm friggin' loving driving the wagon again. :banana:

wish you guys were open on weekends :(

wish you guys were open on weekends :(
We hear that an awful lot!

Phil
Andrewtech Automotive

I would like to say thanks to all the great people up there at Andrewtech for my awesome new tranny and even puttin' the timing belt on too. You guys rock... sorry I had to stick around there the whole time but didn't have many places to go since I came from VA Beach and drove through a tropical storm to give you all of money. :lol:

You guys rock :banana:

RWD conversion by PPG

Hum.:cool:

RWD indeed 8)

Phil
Andrewtech Automotive

i've heard phil @ andrewtech really knows what he's talking about!

i've heard phil @ andrewtech really knows what he's talking about!

Lies!:confused:
Andrew

well he knows how to answer to customers when they give him a gift. :), Like dvds

i've heard phil @ andrewtech really knows what he's talking about!


Phil.......nahhhhhhhhhhhhhhhhh

:lol: :lol: :lol:

well he knows how answer to costumers when they give him gift. :)

In English??

well he knows how answer to costumers when they give him gift. :)

That's not how it works in this country! If you are wearing a costume, you say "trick or treat" and then HE is supposed to give YOU candy! :lol:

EDIt!!!!!!!!!:):):)

bump, haventy seen youall in a while :(

AP still around?

i need me an andrewtech license plate frame. gotta replace the one i have on it now :rolleyes:

1 AP left for a 2002 WRX!

We've got many license plate frames around!

Phil
Andrewtech Automotive

any AP for an 04 WRX

how much just for 1-2 straight cut and 3-4 helical...gears only, no install :-)

Just a 1-2 straight, 3-4 helical? Synchro I suppose? $3500!

Phil
Andrewtech Automotive

still got that roof scoop? im dying for it

1 AP left for a 2002 WRX!

We've got many license plate frames around!

Phil
Andrewtech Automotive

I want one of these when I bring my car in tomorrow. I've been too lazy to get the old deealership frames off.

Please check your PM box.

I'm currently shopping around for best price quote on service. Details are in the PM I sent you.

Thanks.

Please check your PM box.

I'm currently shopping around for best price quote on service. Details are in the PM I sent you.

Thanks.

I can't tell you that andrewtech is the cheapest, but they are extremely competative for price and they do great work. How much cheaper are you going to get by risking bad service?

Agreed. I know about the quality of Andrew Yates' work. He worked on my car when he was still at Hillmuth. His work left a very good impression on me.
I can't tell you that andrewtech is the cheapest, but they are extremely competative for price and they do great work. How much cheaper are you going to get by risking bad service?

You guys have your big ol' gearboxtech.com window decals in? As I told Phil over the phone I'm gonna need some Andrewtech lovin' next week.

john

Cam - Yep, sitting on the stool where you left it!

AllAWD - Come on by!

Anonymouse20910 - I'll check in a minute. I'm sure we can set you up.

John - I had no idea that was you! I thought the last name sounded familiar, but next time just say it's John-Buttdyno! I'll try and make sure there are no STi-LTD's around when you come by.

Phil
Andrewtech Automotive

John - I had no idea that was you! I thought the last name sounded familiar, but next time just say it's John-Buttdyno! I'll try and make sure there are no STi-LTD's around when you come by.:lol: Yeah I try not to introduce myself as such when I'm at work.

http://i31.photobucket.com/albums/c394/JasonFerrell/DSCF1344.jpg

And that's what my front/right axle looks like now :)

john

Hey guys Ill be there first thing in the AM. I need a Clutch big time.
Freddy.

You guys have your big ol' gearboxtech.com window decals in? As I told Phil over the phone I'm gonna need some Andrewtech lovin' next week.

john
Man, I haven't even been there yet (knocks on wood), but I've been rockin it for a long time now:

http://dave.oc7.org/images/2006.07.01.chik-fil-a/images/DSC_6193.jpg

That being said, I need a bunch of work done =P

My 5th to 4th shift does not work w/o double clutching and revmatching...everything else is fine...dunno what is up with it.

-- Dave

Hey guys Ill be there first thing in the AM. I need a Clutch big time.
Freddy.

First thing in the AM? I was there at 745!

First thing in the AM? I was there at 745!

I showed up right when you going to get dropped off. You have the blue bugeye with projectors, STI grill...etc.?

Mine is a stock-looking silver bugeye.

I saw Freddy....about 9:30am :)

I showed up right when you going to get dropped off. You have the blue bugeye with projectors, STI grill...etc.?Aye, that's me :)

I do remember seeing a silver bugeye...

Check your PM's :)

I need me a big gearbox tech window banner.... for sure

I need me a big gearbox tech window banner.... for sure

Are you getting the hang of clutchless???
Andrew

Andrew, check out the website prototype I emailed you. If it sucks, I can fix it :)

john

Any new info on the ATB center diff you guys were planning to test and make available. I need a new center diff since my RS now acts like a RWD car all the time. I have a spare but would like to source some helical diffs for the RS and the LRXTi

jake
www.moranbros.com

free bump, im going to have some work for you guys come late spring/early summer :D

when does phil come back? sorry i havent been by in a while, work/school/everything else has kept me busy as hell

Bump for new info!!

But the real question is... do you have huge-ass Gearboxtech.com stickers?

My rear window is naked. And I have magnets.

PM Sent.

But the real question is... do you have huge-ass Gearboxtech.com stickers?

My rear window is naked. And I have magnets.

Pretty big..... I'll put some in the mail to you.

Andrew

I'll be getting an alignment soon (whenever my damned coilovers get back to me) so you don't need to mail it :)

john

I have a bigass sticker that I have to figure out which car to display it on...and where...

I may have to take some pics and chop it on to decide.

-- Dave

What's the dealio on the RWD conversion set up??? PM me.

Are you ever going to do a group deal for helical ppg set 1-4 for an 07 STI??? I could be that group....:cool:

omg!! thx for installing that SWEET bov fer me today,, it costed much less than i thought and it sound so fast!!!11 i be tAking my sweet intake to have you guy nstall it too yo!

mad jdm tyte son

Rumor has it that they may have an RSTi for sale as soon as they figure out that I can't afford my pending repair bill :lol:

-- :(

if dan still wants a discount at lowes on a lawnmower, he has about 2 days till my employee discount stops working

you guys wiill be happyyyy

i just bought a utec :D

any psi boost gauges?!

any psi boost gauges?!


Saw it today.... Sweet... Take a look at the first post.... (PAGE 1):lol:

Cy'all on Thursday for my alignment/cornerweighting.

Oh yayees.

any psi boost gauges?!

60mm Smoked face white and smoke face amber psi boost gauges in stock!!

i'll have pics of my stri gauges up sometime soon...don't wanna take pics til i get all 3 installed and working but they look good. they match the sti dash pretty well, they're just not as red.

i'll have pics of my stri gauges up sometime soon...don't wanna take pics til i get all 3 installed and working but they look good. they match the sti dash pretty well, they're just not as red.

Got Pics?? :lol:

-Edwin

Got Pics?? :lol:

-Edwin
You gonna answer my PM? Huh? ;)

-- Dave

You gonna answer my PM? Huh? ;)

-- Dave


That's a long PM! I tried to call you and no answer!! :rolleyes:

:lol:

-Edwin

That's a long PM! I tried to call you and no answer!! :rolleyes:

:lol:

-EdwinI can't bring my phone to work...

You have to call me before 8 or after 6...

-- Dave

Updated again....

Andrew

edwin its sam, my oil pressure gauge is reading off the gauge. i dont know what happened. what can be done?

*ponders messing with alignment before Subaru Challenge*

edwin its sam, my oil pressure gauge is reading off the gauge. i dont know what happened. what can be done?

Bring it by? Sender may have failed.

-Edwin

nevermind found the problem. sender was touching the intake manifold. thanks though! little zip tie took care of the problem

You Have PM :)

thanks again for letting me come down and film.. it was good to catch up with you guys. nicks car is doing great and he loves it!

happy belated bdays to edwin and dan!

and uh...thanks for the wang in the vid ;) you guys are priceless.

-raj

thanks again for letting me come down and film.. it was good to catch up with you guys. nicks car is doing great and he loves it!

happy belated bdays to edwin and dan!

and uh...thanks for the wang in the vid ;) you guys are priceless.

-raj

Anytime Raj, you're always welcome!

-Edwin

post that video up!

...got any specials going on for a clutch and flywheel for my car? What are my options?


Thanks,


CK

post that video up!

in the process of editing right now.. a teaser should be up in the middle of the month. ill ask a-team if they wanna host the vid on their site otherwise i am going to use it in my doc that im maken.
-raj

...got any specials going on for a clutch and flywheel for my car? What are my options?


Thanks,


CK

Whoa!

Crazy Ken sighting!!

...I know...I know...long time no post!


CK


So Andrew ... you got anything for me???

...I know...I know...long time no post!

CK

So Andrew ... you got anything for me???Holy Kenny. :lol:

...got any specials going on for a clutch and flywheel for my car? What are my options?


Thanks,


CK

What kind of clutch and flywheel are you looking for? I think we can work something out.

-Edwin

New Turbo blankets available for GT style turbos! Pics added on first page.

-Dan

i need an alignment! any possibility of coming by tomorrow? and how much?

i need an alignment! any possibility of coming by tomorrow? and how much?

Swamped tomorrow... Next week?

-Edwin

jeebus you could use that turbo blanket as an emergency blanket if you got a tune in fallston and your car left you stranded on a cold snowy mountain side in the winter...

What kind of clutch and flywheel are you looking for? I think we can work something out.

ACT - Clutch (perf. street disc) and Streetlite Flywheel

What kinda offer can you make??? I am VERY interested!!!

:D


CRAZY KEN

What kind of clutch and flywheel are you looking for? I think we can work something out.

ACT - Clutch (perf. street disc) and Streetlite Flywheel

What kinda offer can you make??? I am VERY interested!!!

:D


CRAZY KEN

I'm liking.... $819.

-Edwin

...and installation? Everything out-da-door...botonline pricing? How long do you need the car?


Thanks,


Ken

I want my turbo. and I'll have my fujitsubo headers in but I need them heat wrapped. Got the wrap or should I bring that with me??

I want my turbo. and I'll have my fujitsubo headers in but I need them heat wrapped. Got the wrap or should I bring that with me??

Got the wrap, just waiting on the turbo.

-Edwin

Thanks for the ride today Edwin!!! I hope i can get that screen off your hands :)

Can you guys get the the regular size turbo insulation to fit a 16g? Like maybe the thermotec stuff?

Are you guys doing construction to your website?

Can you guys get the the regular size turbo insulation to fit a 16g? Like maybe the thermotec stuff?

Yea I can. Shoot me a PM or call if you need some!

Are you guys doing construction to your website?

Constantly. We are hoping to have it 100% before the new year.

-Edwin

pm me a price for the utec w/ map switch please.thanx,mike

would you guys happen to have an intermediate pipe laying around? or possibly fab one up so i can buy an axleback and be able to use it with my helix dp?

pm me a price please!

Hey duders, price on catless Invidia downpipe installed?

PM's sent!

-Edwin

You need subaru part #10993AA031 in stock. They come in packs of 12.
You also need #10993AA041 They come in packs of 16. :)

They hold the camshaft cap in place on EJ25 motors...

Quite useful for replacing ones that might have been stripped out and then cut off by shade-tree shops ;)

I hear that Jackie can get ahold of these within 3 business days too!

-- Dave

I do... and your motor WAS going to be done tomorrow. But now i'm not so sure... :unamused:










:lol: :D :lol:

i was wondering if you guys were selling the 4" TXS downpipe only? am really interested. THanks!

-Simon

I need a Tx upPipe for the Wifes car>!

http://www.seatstaysup.com/forums/misc/SEMA2007/images/IMG_2904.jpg

what did u guys have to do with this build?

I remember being there when they were doing engine work on one of those puppies because some other shop didnt quite get things right. Could be that same car.

http://www.seatstaysup.com/forums/misc/SEMA2007/images/IMG_2904.jpg

what did u guys have to do with this build?

Parts supply and assistance in the build as a whole. And maybe talking about a T56 Dogbox?? :)

-Edwin

any invidia g200s in stock? if so how much shipped to virginia beach, va 23453. pm me the details.

Anytime for my TUNE? I'm off Monday???

Your pm box is full.

Will the turbo blanket fit a vf39 or will it be to big? Please pm price for the blanket if it fits a vf39. Plus, please send price for X-Line boost and EGT shipped 23320. What color options are avaliable for the X-Line? I have a WRX and would like to try and match if possible. Thanks.

PM's sent!

-Edwin

As a note: The blankets will only fit GT series turbos.

We're going to continue the install specials going for the next month or so. Take advantage!

Andrew

Winter Service Special:
Oil Change (Motul Synthetic)
Tire Rotation
Coolant Flush
Top Off Fluids
Check Tires/Brakes
Check Belts/Hoses

Andrewtech Winter Special Price: $175



Turboxs Parts Install Specials:

TurboXS WRX/STI Short Ram: $165 Installed
TurboXS WRX/STI Turbo Back Exhaust: $1075 Installed
TurboXS WRX/STI TMIC: $775 Installed
TurboXS WRX/STI FMIC: $1400 Installed
TurboXS WRX/STI Utec Delta: $940 Installed
TurboXS WRX/STI Utec Delta Map Switch: $99 Installed
TurboXS WRX/STI Radiator Hose Kit: $175 Installed

Clutch Install Specials:

2002-2005 WRX Exedy Stg 1: $850 Installed (Add ACT Streelite flywheel for $250)
2006-2007 WRX ACT Street/Strip: $1000 Installed(Add ACT Streelite flywheel for $250)
2004-2007 STI Exedy Stg 1: $900 Installed(Add ACT Streelite flywheel for $300)

Other clutch install options are available, call for pricing.

PPG 1-4 straight cut, or PPG 1,2 straight, PPG 3,4 hel? Blouch 16g hasn't broken anything yet, but never to early to save.

Also, price me on this response please.
Might be able to get a dead trans. Would my PPG 1,2, late 05 3,4 fetch any money back? Especially if I kept it all cased?

Thanks
JD

Hey Edwin,

Please pm me a price on the new tial blow off valve if you can get them or when you can get them.

Edwin is no longer at Andrewtech. :)

Hey Edwin,

Please pm me a price on the new tial blow off valve if you can get them or when you can get them.

Shoot an email to:

sales at andrewtechautomotive dot com

or call the shop at:

240-683-1000


-Ed

I want whats on the top shelf all the way to the LEFT......


PLEASE

(Hint~6th)

Bump for the BEST Shop In MAIC!~

I want whats on the top shelf all the way to the LEFT......


PLEASE

(Hint~6th)

Bump for the BEST Shop In MAIC!~

Will that be Cash or Credit? :banana:

Thanks for swinging by yesterday.

i need brakes really bad i almost crash my car today

Edwin is no longer at Andrewtech. :)

what :eek:

Did he break customer's car again?

do you guys have brakes on stock??

...Whatcha got in stock or on SPECIAL for '05 Legacy GT's???

Thanks,

CRAZY KEN

Maybe one day I'll swing by and findout for myself personally.

...Whatcha got in stock or on SPECIAL for '05 Legacy GT's???

Thanks,

CRAZY KEN

Maybe one day I'll swing by and findout for myself personally.


Dude, you definitly live close enough lol. Tell me when you head up there, I might need some stuff too :(.

pm me a price on invidia catted dp.also do you install aquamist kits?

do you guys have brakes on stock??

wrxspeed1,

Yes, we do. If not, we can definitely order them and get them shipped quickly. Shoot us an email at sales@andrewtechautomotive.com or give us a call at 240-683-1000 to place an order.

...Whatcha got in stock or on SPECIAL for '05 Legacy GT's???

Thanks,

CRAZY KEN

Maybe one day I'll swing by and findout for myself personally.

CRAZY KEN,

Your specials will only be revealed to you at the shop. Our address is:

7615 Rickenbacker Drive
Unit E
Gaithersburg, MD 20879

Seriously CK, what are you looking for? Use above info to contact us! :)

pm me a price on invidia catted dp.also do you install aquamist kits?

rallyracersti,

We'll send you a PM shortly. Yes, we do install Aquamist kits. We've installed quite a few. :)

talked to that guy 'tapout' who refered me to your shop. seen what his car did this weekend at the track and he told me u guys do excellent work.looking forward to your pm .

Yo man, where have you guys been. Call me back or pm me back. Car is waiting for you guys.

Yo man, where have you guys been. Call me back or pm me back. Car is waiting for you guys.

???

Try the shop phone (EST) b/w 8am-6pm Mon-Fri 240-683-1000

or email at:

sales@andrewtechautomotive.com

???

Try the shop phone (EST) b/w 8am-6pm Mon-Fri 240-683-1000

or email at:

sales@andrewtechautomotive.com


Yeah, I called a few times and left a message. I know they are busy so I''m not too worried. I just am eager to get this trans in the car and run this bad boy. This along with my new engine and turbo should be fun.

Yeah, I called a few times and left a message. I know they are busy so I''m not too worried. I just am eager to get this trans in the car and run this bad boy. This along with my new engine and turbo should be fun.

:D I called Dan (I'm at my "real job") and told him to check the messages and email.

-Ed

Ed's the man for helping out so much! Love you long time!

Andrew

any turbo blankets for the VF turbos?

also im looking for a Meth kit what do you guys have in stock? and what do you recomend

Ed's the man for helping out so much! Love you long time!

Andrew

Gracias, boss. :D

any turbo blankets for the VF turbos?



Rumor has it that a VF-friendly blanket is in the works! :banana: I wants!!!

Regarding your meth-kit question, call the shop or email:

240-683-1000

sales @ Andrewtechautomotive dot com

PM sent!

PM sent!

Actually, please do not send PMs. The best way to contact the shop is via email (sales at andrewtechautomotive dot com) or call b/w 8-5:30 p.m. M-Th, 8-4p.m. Fri.

phone: 240-683-1000

Actually, please do not send PMs. The best way to contact the shop is via email (sales at andrewtechautomotive dot com) or call b/w 8-5:30 p.m. M-Th, 8-4p.m. Fri.

phone: 240-683-1000

Ah, sorry about that. I sent another PM before I read that reply, I promise thats the last one.:p

Thanks for the services yesterday! Awesome as always.

Posting here to remind Ed or someone to remind Ed to bring my calipers back to NoVA this week ;)

Thanks!

-- Dave

Posting here to remind Ed or someone to remind Ed to bring my calipers back to NoVA this week ;)

Thanks!

-- Dave

Dave, please call me or the shop tomorrow. Preferably around noon?

thx!

-Ed

dan and andrew,

im looking for sponsorship?...haha
btw: stage 2 is running perfect...
i couldnt be happier, just sucks that gas is what it is...

Hey...e-mailed you guys on friday about new rotors/lines/pads etc. I don't know if you haven't had time to respond cause yall are busy but I'll give you a call later today.

thanks again for the great service, tranny shifts like butter now. It was nice to meet you guys too. Looking forward to bringin my car there again. -Jeremy

I have got three gearsets here cluttering up my shop and need to go.

The first is a KAAZ 1-5 straight cut synchro gearset. It was freshly rebuilt and ready to go in a transmission. Just bring me your box, loose from the car, and you can have the KAAZ set for $2500 installed.

The second is a used RA 1-5 set. The gearset was used for a week or so before someone changed their mind. Bring be a transmission to build it in and you can have it for $1600 built.

The final set is a built transmission (3.90 final drive with a 1.1:1 transfer gear ratio). It's an MRT helical synchro gearset. New synchros, fully refreshed. I'll install the transmission into your car for $4000 with your core.

First come, first serve!

Phil
Andrewtech Automotive

nice!

would you be willing to just sell the KAAZ gears :D

Is that second one built and installed or just built?

The KAAZ set and the RA set are loose. I'll take your transmission, pull out your stock gears, and replace them with the KAAZ or RA set. The price I listed includes labor to install it into your transmission (though not labor to remove and reinstall the transmission into the car).

The MRT set is already in a case ready to go, but I need a good core to replace it. The $4000 includes the R&R in the car.

Bump for some good deals!

pmed ....

Updated special service pricing in orignial post.
Thanks for looking!

-Dan

Andrew will cuddle up next to you if you fall asleep while waiting for your car

Pm sent! :)

Andrew will cuddle up next to you if you fall asleep while waiting for your car


Hey Guys thank you for the A+++++ Service. And thank you Andrew and Dan, the Kaaz Gearset is working great.

BTW. Andrew didnt cuddle up next to me while i was waiting...: )

Ziad

P.S. 5th gear @ 80mph @ 4250rpm is amazing...

We have alot of customers taking advantage of the maintenance special pricing.......I think we're just going to leave the prices where they are to help people save for the holidays.

Andrew

It's a Christmas Miracle! :D

Andy Claus?

Working on a low priced t-belt/water pump special right now.

Had my 30K service done... Paid WAY less than dealer quoted me and received a lot more - great service and top of the line fluids, etc.

Dealer quoted me higher price to "Inspect" fluids and etc... Andrewtech REPLACED fluids with fresh ones for a lower price...

In 30k, my car will be going straight to AndrewTech again :))

Very happy customer :banana:

p.s. dealer quoted me $600...

Working on a low priced t-belt/water pump special right now.

I hope that one last a while, I'm past 93k and will be in for the t-belt sometime.

Can't Andrew fix the stock market?

He is a miracle worker.

I hear that you guys have my black 2-pot calipers (From Frank) lying around somewhere?

Can anyone send those home with Dan?

Thanks,

-- Dave

Can't Andrew fix the stock market?

Im not sure about fixing the stock market, but he could kick your ass in Halo. :lol:

Im not sure about fixing the stock market, but he could kick your ass in Halo. :lol:

You know it! I'm playin all night tonight!

Andrew

You know it! I'm playin all night tonight!

Andrew

Pmed you man!!

did you guys get the shift knobs yet?

oh and Dan, I lost your cell number. Give me a call again about that little clip that you hopefully still have for my car.

-paolo

Andrewtech does it again........like always thanks for a great service yesterday.......and thanks dan for stickering me up........the new silver stickers are sick

Hey I'm wondering how much it would cost me to drive in with no core and get LGT 1-2, and fresh syncros. I've been driving around with no 2nd for a week, and I can't afford to wait much longer before more damage occurs.

Car is an 05 Saabaru turbo by the way.

Got the special going for T-belt!

Andrew

Just wanted to mak sure everyone saw that we are doing t-belt replacement for $300 parts and labor!

Give a call about a stock clutch replacement for $650 parts and labor if you in need of this service.

Andrew

Talked to you guys today, see you soon!

I need a clutch, Ill be contacting you soon!

Bump for awesome service received days ago!

I think i'm going to have to give you guys a call about the timing belt special. thats a great deal.

Andrewtech Rocks my Socks. That is all.

im coming tomorrow bump since you guys rock peoples socks off.......haha

Andrewtech Rocks my Socks. That is all.

sounds a little gay man.....




:lol: great dudes at Andrewtech. Give Dan and Andrew a hug.

...yesterday!

Getting lots of stuff done before the new year...hopefully it won't hurt my wallet too too much.

Boost, AFR/Volt, Oil Press. & EGT Gauges Installed
Axle Replaced
Timing Belt Replace
Water Pump Replaced
Thermostat Replaced
Radiator Flush
Differential Fluids Replaced
and Fix My Clutch

Great guys, knowledgeable and customer friendly...My x-mas wish for this year is I hope my organic clutch isn't fried! It's only 4 months old!!!

BTW, I dropped off my car the day that they are moving to their NEW LOCATION...I should hear from them sometime next week.


CRAZY KEN

^^ I just found out they were moving......I dont know why there hasnt been a big hype about it.......they think they can move and we wont find out, PLEASE......:D:D

Ill be there arround 3:30 today picking up my car

Welcome to 2 months ago. :)

just came back from picking up my car.....the only problem is that I go there for 5 mins and end up staying there for more than 1 hour......ahhhh the smell of gear oil......haha

Hey did you guys move? if so were too.

Quote:
Originally Posted by MilesToEmpty View Post
Im not sure about fixing the stock market, but he could kick your ass in Halo.
You know it! I'm playin all night tonight!

Andrew

Pmed you man!!

Flippin hit me up too the name is BoldasLions haha!

Hey did you guys move? if so were too.

Their new address is:
8029 Cessna Ave
Gaithersburg, MD 20879

I'll be there MLK Jr day for a timing belt so long as they don't decide to close.

getting rid of parts inventory BUMP!

parts listed on first page!

PM with any questions!!!

SZ49 does it have a 3" inlet? How much more to have the wastegate shut? Is it new or used, if used...how many miles on it? What are the est. number for this turbo? What is the max psi? At what rpm does it start to spool?

Thanks,

Ken

new week bump!

Is a SZ49 bigger than a 20G?

SZ49 does it have a 3" inlet? How much more to have the wastegate shut? Is it new or used, if used...how many miles on it? What are the est. number for this turbo? What is the max psi? At what rpm does it start to spool?

Thanks,

Ken


Bump for the same

Bumps for you. See you doods Saturday.

Got a 5 quart/liter(?) jug of Motul I can buy this afternoon?

5W40

We have 3 =)

Thanks, I'll be by some time today. I have another appt. over there this afternoon.

Bump! Check your PMs.
Thanks.

plan on swinging by for that catted pipe friday !!!