View Single Post
Old 01-30-2013, 11:40 AM   #1
06rexwagon
Scooby Specialist
 
Member#: 114730
Join Date: May 2006
Chapter/Region: SWIC
Location: Albuquerque, NM
Vehicle:
2006 WRX Limited Wag
9.8@150

Default Borg Warner EFR9180- 2006 WRX Wagon

I edited this post and somehow double posted- mods please delete either one.


Event: Dyno Tune
Location: Pro Power dyno, Rio Rancho NM
Ambient Temp: 50
Elevation: 5400'
Weather: cloudy
Tires: Bridgestone RE090's- then again on BFG G force drag radials
Car: 2006 WRX Limited Wagon
Tuner: Myself
Dyno Info: Dynojet
Transmission: 2005 STi 6MT with rallispec long gear set
Gear: 3rd
Peak HP at RPM: 823 at 6700
Peak Torque at RPM: 667 at 6200
Baseline hp/tq for a stock STi: 245-255hp/250-260tq
Target Boost: 33
Target AFR: 11.3
Fuel: E70 (winter blend)
Engine/Power Modifications:


AEM EMS V1
2005 EJ257 Block sleeved by Benson
CP Pistons 99.5mm (moly coated skirts, ceramic crowns)
Carrillo Pro H beam rods, Carrillo bolts
Heat treated oem crank
King bearings
2006 Sti AVCS heads, ported
GSC Stage 2 cams (272, AVCS)
BC +1mm intake/exhaust valves
BC springs, titanium retainers
ARP L19 Studs
08 Sti oil pump, 11mm
TGV deletes
AP Fuel rails
Aeromotive FPR
ID2200cc injectors
Integrated Engineering Surge tank with Dual bosch 044 pumps
Cosworth Intake manifold (reverse mount)
Treadstone fmic core
Full Race Twinscroll T4 rotated turbo kit
BorgWarner EFR 9180 EWG 1.05 T4


Finally got to put the EFR through it's paces. I had previously run the S300SX 91-79 .91 AR on the car and was pretty happy with it.
I am AMAZED that a 94lb/min turbo is spooling 400-500rpm sooner than the older 82lb/min turbo.
On the first trip to the dyno last week I ran my 2007 STi RE090 tires which have good tread but are very dry. The car made 805/636 SAE at 33psi, but I suspected the tires were spinning. Here's a graph of those pulls:



And a graph vs the old 91-79- The 91-79 was at 34psi.



I decided to try the dyno again yesterday, this time with my drag radials. The results were that the car held traction better to about 6500rpm, then let go hard. The tune and boost were untouched from the previous dyno.




Now, SAE numbers are great for bragging rights, but we are at 5400' and our correction factor is pretty high. Here is the uncorrected graph, which in my opinion is still a lot of power for this altitude, at only 33psi ( I want to run 37-38 but need traction). A stage 2 STi only makes 250 uncorrected on this dyno.





Someone want to help me embed these?

https://www.youtube.com/watch?v=ncnswSPEq4M

https://www.youtube.com/watch?v=4u0JHvsxEZc

low quality phone vid of the 823 pull
https://www.youtube.com/watch?v=CViAUFZeBwk
* Registered users of the site do not see these ads.

Last edited by 06rexwagon; 01-30-2013 at 11:50 AM.
06rexwagon is offline   Reply With Quote