Welcome to the North American Subaru Impreza Owners Club Friday August 29, 2014
Home Forums WikiNASIOC Products Store Modifications Upgrade Garage
NASIOC
Here you can view your subscribed threads, work with private messages and edit your profile and preferences Home Registration is free! Visit the NASIOC Store NASIOC Rules Search Find other members Frequently Asked Questions Calendar Archive NASIOC Upgrade Garage Logout
Go Back   NASIOC > NASIOC Technical > Engine Management & Tuning > UTEC

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.
* Registered users of the site do not see these ads.
 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 07-27-2006, 12:46 AM   #1
SloRice
Scooby Specialist
 
Member#: 44351
Join Date: Sep 2003
Chapter/Region: MWSOC
Location: Cincinnati, OH
Vehicle:
2004 Mitsubishi Evo
701whp 9.91@146

Default UTEC, DTEC and Speed Density

Since we all know about the new speed density firmware coming out, I am going to be getting tuned with it next weekend. So we started working on the blow through MAF setup tonight. After talking to Nathan@TXS, tmarcel and Tim Bailey, we went ahead and cut the MAF wires to extend them and used shielded wire on the appropriate MAF wire. Once it was all done, we wanted to start it just to see if it would. My car is already tuned for a BigMAF which is ~3" diameter and the blow through pipe we used is 2.75" diameter, so if it started, it was going to be pig rich and it was....idled at 11:1 AFR. Since I'm only going to be using the MAF for idle control, I didn't care to much about stuffing a 3" or larger diameter pipe in there for MAF resolution. I just want the car to idle normally and it did...rock solid at 900RPM's. Blipped the throttle and it cames right back to 900RPM. Hell it idles better now than it used to, just a few points richer AFR. I have about 4" inches of straight pipe on either side of the MAF sensor. So get my tuner to recalibrate the AFR in the ECUTek and UTEC and it should be good to go!!

Now the next step in the process is to see if I can split the signal off of the DTEC MAP sensor and run it into the signal line on the stock MAP sensor. Then have my tuner recalibrate the ECU and UTEC for the new MAP sensor. That way I have a 4.5 bar MAP sensor to tune the UTEC with instead of the 23psi limit the stock MAP sensor has. I spoke to both Mark and Nathan at TurboXS and they said it might work, but they aren't sure. If not, I spend $100 and get another MAP sensor from them and wire it in where the stock MAP sensor is. Does anyone have any thoughts on this as this is my main concern now. I cut open the shielding for the DTEC MAP sensor and the last picture is what's inside. Anyone know which one is the signal wire to tap into? Also did I screw myself by cutting the shielding?

And pics for the kiddies!!







SloRice is offline   Reply With Quote
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
cold weather and speed density qwkwrx UTEC 5 01-23-2010 12:08 PM
utec, speed density, and misfire codes MRX WRX UTEC 240 06-16-2009 11:31 AM
UTEC Speed Density Tuning How-To? Zumble UTEC 2 02-10-2007 03:16 PM
Utec Delta with Speed density 437whp on pump 91 AZScoobie Proven Power Bragging 39 09-26-2006 09:05 PM
Switched to Blow-thru and Speed-density via 5.8, pics inside NavyBlueSubaru UTEC 25 08-13-2006 04:07 PM


All times are GMT -4. The time now is 04:08 PM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2014 Axivo Inc.
Copyright ©1999 - 2014, North American Subaru Impreza Owners Club, Inc.