Welcome to the North American Subaru Impreza Owners Club Saturday November 1, 2014
Home Forums WikiNASIOC Products Store Modifications Upgrade Garage
NASIOC
Here you can view your subscribed threads, work with private messages and edit your profile and preferences Home Registration is free! Visit the NASIOC Store NASIOC Rules Search Find other members Frequently Asked Questions Calendar Archive NASIOC Upgrade Garage Logout
Go Back   NASIOC > NASIOC Technical > Engine Management & Tuning > AccessPort

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.
* Registered users of the site do not see these ads.
 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 02-25-2007, 08:09 PM   #1
shane04
Scooby Newbie
 
Member#: 129189
Join Date: Oct 2006
Chapter/Region: NWIC
Location: port orchard
Vehicle:
04 wagon
jbp surgeline tuned

Default not going into test mode when uploading a new map

i have a v1 ap put on a downpipe today, went to flash from stage 1 to stage 2 91 oct., the car went into test mode as it should,evrything seemed good,finished flashing and the car wouldnt start.after looking everything over, ensuring evrything had been disconnected properly i tried flashing the car to a stage 2 93 oct map, and noticed the car wouldnt go into test mode,tried flashing anyway and it still wouldnt start, so i reverted to stock, car started up i only ran it for a minute, shut the car off.i downloaded another stage 2 91 oct map from cobb and tried flashing it, this time the car went into test mode but once the flash was finished the car would not start.then i tried flashing to the stage 1 91 oct map that i had been running and the car would not go into test mode.then i got the "error please try operation again" message.looked it up in the manual and its the code for car not going into test mode,poor connection.tried resetting the ecu by disconnecting the battery,tapping breaks and letting it sit for an hour.then connected everything back up and tried to revert to stock,no test mode and the same error message.


this is on an 04 wrx with ap v1, any ideas?
shane04 is offline   Reply With Quote
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
is there another way to get into test mode? likekris Open Source Reflashes 3 05-26-2008 02:52 PM
Need help!!! Car won't go into test mode wuuusaa Factory 2.5L Turbo Powertrain (EJ Series Factory 2.5L Turbo) 5 02-28-2008 04:59 PM
Not going into gear when car in running... Midnight25rs Transmission (AT/MT) & Driveline 5 10-20-2007 04:04 AM
AP - Car won't go into test mode! Help please. Anihil8r AccessPort 18 03-24-2006 03:39 PM
car not going into Test mode with AP Lordhowe Engine Management & Tuning 2 08-27-2005 04:32 PM


All times are GMT -4. The time now is 04:30 AM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2014 Axivo Inc.
Copyright ©1999 - 2014, North American Subaru Impreza Owners Club, Inc.