|
|
|
|
Thread Tools | Display Modes |
12-21-2005, 08:45 AM | #101 |
Scooby Newbie
Member#: 88950
Join Date: Jun 2005
Location: Reston, VA
Vehicle:2003 MSP Protege` Silver |
Great write up. A few quick questions though, since I am a beginner (already made an unfortunate mistake of buying a Dynamat trunk kit).
1. When you speak of adding foam above the layers on the outer door, do you mean just behind the speaker, or the entire door? 2. Could you describe the door speaker baffles a little better? 3. How do you seal off the access holes with tin/aluminum (glue, weld, rivetm, etc)?
* Registered users of the site do not see these ads.
|
12-21-2005, 02:51 PM | #102 |
Scooby Specialist
Member#: 54604
Join Date: Feb 2004
Chapter/Region:
MAIC
Location: Severn, MD
Vehicle:2004 FXT Cayenne Red (sold) |
1) Layer of raamat on the whole inside of the exterior shell of the door followed by ensolite on the whole inside of the exterior of the door.
2) not sure how Rick did this one. 3) I believe earlier in this thread or another he mentioned using self tapping screws to attached the aluminum. Frank Happily deadened via this thread |
12-21-2005, 06:53 PM | #103 | |
Scooby Newbie
Member#: 88950
Join Date: Jun 2005
Location: Reston, VA
Vehicle:2003 MSP Protege` Silver |
Quote:
outer shell | mat | foam | inner shell | mat | foam .... ? So you cut the tin to shape over the holes, attach at a few points with self tapping screws, then mat over them. Do you use any type of material to put inbetween the tin and door shell? |
|
12-22-2005, 11:53 AM | #104 |
Scooby Specialist
Member#: 54604
Join Date: Feb 2004
Chapter/Region:
MAIC
Location: Severn, MD
Vehicle:2004 FXT Cayenne Red (sold) |
Your pic is correct but I didn't add tin pieces. I just stretched the pieces of mat over the holes. Lazy I guess. Your directions sound like rick did. I don't really see a need to put anyting between the tin and the door metal, as it will all be covered so resonance won't be an issue.
Frank |
01-15-2006, 02:27 PM | #105 |
Scooby Newbie
Member#: 44504
Join Date: Oct 2003
Location: San Jose, CA
Vehicle:1996 Legacy L Sedan |
Update on the 06 WRX wagon sound deadener install
So we finally got around to working on the front half of the sound deadener install on my friend's steel grey 2006 WRX Sport Wagon.
We got the seats out: Then methodically removed the carpet and dozens of fasteners that hold it in. Put down some BQuiet butyl mat and then a roll of BQuiet foam on top. Getting the seats out is pretty easy. But those electrical connectors underneath are crazy - none of them unclip the same way. |
01-15-2006, 02:34 PM | #106 |
Scooby Newbie
Member#: 44504
Join Date: Oct 2003
Location: San Jose, CA
Vehicle:1996 Legacy L Sedan |
Once the carpet was out, you can also see other interesting Subaru engineering techniques such as the plastic runner for the rear floor vents. It is held on by a white clip at the blower outlet.
Once that was removed, the mat was installed and the vent tube refitted. The rear floor area was matted as well. While the front seats were out, we install a pair of Wet Okole seat covers. They fit great and will help protect the leather seats from the sweaty mountain bike rides. |
01-15-2006, 11:52 PM | #107 |
Scooby Newbie
Member#: 66604
Join Date: Jul 2004
Vehicle:'05 WRX STi Crystal Gray |
I've been following this thread...but these latest pictures sicken me. My '91 Mustang was stolen and the interior stripped. It looked like this at the impound lot.
|
01-16-2006, 02:43 AM | #108 |
Scooby Specialist
Member#: 50340
Join Date: Dec 2003
Location: Morgan Utah
Vehicle:05 FXT Crystal Grey Metalic |
That stinks buddy, dang thieves, one thing though, I feel pity for people like that, not pity and want to slap them on the wrist and blam society, parents, etc, pity because they have such a sorry life.
Rick |
02-01-2006, 07:56 AM | #109 |
Scooby Specialist
Member#: 42540
Join Date: Aug 2003
Location: Santiago, Chile
Vehicle:2007 Forester XT Metallic Grey |
Was reading the trunk installs threads, and thought it was time to bring this thread back to life
BTW, I have not finished my deadening work yet, a couple of ensolite details are missing, but all I can say is: WOOOOAAW!!!! The nicest improvement is the midbass coming from the front doors, and the fact that I can turn the volume up and feel no rattles there......... but the strongest and more obvious improvement was the trunk. I have a wagon, and all I did was covering the holes in the trunk lid, added a little more RAAMMat over here and there, and put ensolite in top of it. Removed the plastic thing that covers the locking system down at the trunk, and added some ensolite there too. Nothing else. And you wouldn't belive how my sub sounds now.......... almost no rattles; can't say NO ,it'd be biased Cheers, MO |
02-02-2006, 03:11 PM | #110 |
Scooby Guru
Member#: 59993
Join Date: Apr 2004
Chapter/Region:
International
Location: WWAAYY west of the Mississippi
Vehicle:Ass, grass or cash no one rides for free!! |
rick,
just got the package thx!! vince |
02-02-2006, 04:47 PM | #111 |
Scooby Specialist
Member#: 50340
Join Date: Dec 2003
Location: Morgan Utah
Vehicle:05 FXT Crystal Grey Metalic |
Great, now get to work!! Great fellow enthusiasts here guys, cool dudes, glad I could help you achieve your goals! Rick |
02-04-2006, 12:38 PM | #112 |
Scooby Newbie
Member#: 44504
Join Date: Oct 2003
Location: San Jose, CA
Vehicle:1996 Legacy L Sedan |
This is what the stock wagon spare tire well sounds like without deadener.
http://media.putfile.com/WRX-Wheel-W...ound-deadening Once the B-quiet (like Dynamat) was installed, it sounds like a dull thud without the ringing in the clip above. |
04-29-2006, 11:03 PM | #113 |
Scooby Newbie
Member#: 21508
Join Date: Jul 2002
Chapter/Region:
Tri-State
Location: New Jersey
Vehicle:'03 WRX Wagon Silver |
Hey, just thought I'd chime in here... I matted my front door 3 1/2 years(!) ago, and am still happy with it.
http://www.clubwrx.net/forums/showthread.php?t=13291 I didn't have a good supply of closed cell foam, so I used extra mat. Rick also made a good recommendation on speakers |
04-29-2006, 11:14 PM | #114 | |
Scooby Specialist
Member#: 102145
Join Date: Dec 2005
Chapter/Region:
MAIC
Location: Virginia
Vehicle:'04 STi/Cobb St. II 18L Java Black Pearl |
Quote:
|
|
04-30-2006, 09:44 AM | #115 | |
Scooby Newbie
Member#: 21508
Join Date: Jul 2002
Chapter/Region:
Tri-State
Location: New Jersey
Vehicle:'03 WRX Wagon Silver |
Quote:
|
|
04-30-2006, 10:08 PM | #116 |
Scooby Specialist
Member#: 88467
Join Date: Jun 2005
Chapter/Region:
NESIC
Location: Super 88
Vehicle:2005 WRX All black everything. |
the only thing better than this write up would be this write with pics.
Great job...sticky vote+1 Thanks Rick! |
04-30-2006, 10:55 PM | #117 |
Scooby Specialist
Member#: 50340
Join Date: Dec 2003
Location: Morgan Utah
Vehicle:05 FXT Crystal Grey Metalic |
Thanks We do have one version, a general install guide with pics, if you want it just email me, [email protected] and let me know
|
07-11-2006, 11:13 AM | #118 |
Scooby Specialist
Member#: 10433
Join Date: Sep 2001
Location: on top of spaghetti
Vehicle:1942 Kettenkrad WR Blue Pearl |
I just did this mainly to lower in-cabin noise. I did the doors and trunk. The doors have a nice thunk to them now. I figured I'd replace the front speakers while I was in there. Here is what I used:
-1 roll of raammat -3 yards of ensolite -1 can of spray adhesive -2'x4' of perforated aluminum (this covered two holes in the rear doors, three holes in the front doors, and two holes in the trunk. I zipped them in with self tapping metal screws.) -1 set of 6.5" Front Adapter Rings from IA Performance -Focal 165 V2 slims -box knife -sacraficial scissors -tin snips for the perf aluminum I guess the only notes I have are that the resonance in the front door are mainly near the bottom, and more than two layers of mat inside the door are a waste. Also, you should only need foam behind the speaker inside the door. There is really no reason to have foam anywhere else inside the door. I matted the whole trunk, which is probably a waste. If I did it again, I would just mat the resonant areas, the wheel wells, and foam the whole trunk. I found the easiest way to apply the mat was to peel back a small strip to position it inside the door, then peel back the rest when it was in place. This was the first time I have done anything like this and it was WAY easier than I thought. I already told a buddy I would help him with his car. He was very impressed with the improvement in my car. |
07-11-2006, 01:20 PM | #119 |
Scooby Specialist
Member#: 50340
Join Date: Dec 2003
Location: Morgan Utah
Vehicle:05 FXT Crystal Grey Metalic |
Thanks for sharing your experiences and results!
I agree, doing the doors is most important and in the STI, sealing off the trunk from the cabin will be much easier and more effective than deadening the trunk fully. One layer on the outer skin of the door, one to two small patches added over that behind the speakers(I prefer two) then a patch of foam over that area only. Once you seal up the openings in the inner door area with the metal and mat then covering it with foam will reduce road noise more, provide a great thermal barrier, help prevent door panel resonance, etc, highly recommended, I would never skip that step. Rick |
07-11-2006, 02:00 PM | #120 |
Scooby Specialist
Member#: 10433
Join Date: Sep 2001
Location: on top of spaghetti
Vehicle:1942 Kettenkrad WR Blue Pearl |
Yeah, sealing up the doors made a huge difference. I drove around with just the outer matting done for a couple of days, and it quieted things down, but once I sealed the doors it was like night and day. I am hoping to get the trunk sealed up today.
Thanks again, Rick. |
07-11-2006, 02:24 PM | #121 |
Scooby Specialist
Member#: 50340
Join Date: Dec 2003
Location: Morgan Utah
Vehicle:05 FXT Crystal Grey Metalic |
Great, glad you are happy buddy
Part of my post was just to ensure others did not miss the part about sealing up the trunk from the cabin as it is more critical in the STI than any other car I have ever worked on. Rick |
07-11-2006, 08:29 PM | #122 |
Scooby Newbie
Member#: 21508
Join Date: Jul 2002
Chapter/Region:
Tri-State
Location: New Jersey
Vehicle:'03 WRX Wagon Silver |
Sealing up the inner door panel also makes the bass response from the door speakers much more effective. Sealing all the openings and caulking around the speaker mounts makes a big difference.
|
07-12-2006, 12:24 PM | #123 | |
Scooby Specialist
Member#: 10433
Join Date: Sep 2001
Location: on top of spaghetti
Vehicle:1942 Kettenkrad WR Blue Pearl |
Quote:
|
|
07-12-2006, 12:25 PM | #124 | |
Scooby Specialist
Member#: 10433
Join Date: Sep 2001
Location: on top of spaghetti
Vehicle:1942 Kettenkrad WR Blue Pearl |
Quote:
Grrr... the wife interupted me, so I didn't finish, but I can tell it is going to help a TON because that is the only place noise is comming from now. hahahaha. |
|
11-15-2006, 12:22 AM | #125 |
Scooby Newbie
Member#: 77625
Join Date: Dec 2004
Chapter/Region:
South East
Location: South East
Vehicle:2005 WRX STi WRB |
What if you don't care about audio at all?
Rick,
I am planning on doing your #1 basic install on my STi. I don't care about car audio at all, but I'd like to cut down on the horrible road noise that the STi has. Can you please elaborate on where you would cut down on your basic install for this situation? Thanks! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
A tutorial on how to install sound deadening material in the front doors? | Jesperss | Car Audio, Video & Security | 25 | 04-19-2013 08:24 PM |
just installed new components and sound deadened the doors... | Damon | Car Audio, Video & Security | 12 | 08-01-2007 09:08 PM |
Does the WRX STi (2004, 2005) have sound deadening? | kimchee_power | General Community | 20 | 05-26-2004 10:57 AM |
New sound deadening material | Sir_Xenon | Car Audio, Video & Security | 6 | 11-25-2003 02:42 PM |
Lightest (and cheapest) sound deadening material? | Alex RS | Car Audio, Video & Security | 14 | 04-30-2001 05:49 AM |