|
|
|
|
Thread Tools | Display Modes |
02-12-2013, 08:54 PM | #401 | |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
Quote:
Anyone have an opinion on problems from putting it on the inside of the curve? Layvon - as far as my trailer goes I have a few tricks. A little trick I learned was to drive the trucks rear wheels up on something to get the trailers tongue farther in the air. Obviously from the picture I have to take the bumper off and usually just put a couple small pieces of wood at the end of the ramps.
* Registered users of the site do not see these ads.
|
|
02-12-2013, 09:10 PM | #402 |
Scooby Guru
Member#: 133146
Join Date: Nov 2006
Location: SC
Vehicle:07 FPgreen 7.37@95 WRX VF39+E85 12.0, 121mph |
That's about where I have my sensor; but my perrin piping goes the other way around.
Last edited by juanmedina; 02-12-2013 at 09:19 PM. |
02-12-2013, 09:22 PM | #403 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
|
02-12-2013, 09:25 PM | #404 |
Scooby Guru
Member#: 133146
Join Date: Nov 2006
Location: SC
Vehicle:07 FPgreen 7.37@95 WRX VF39+E85 12.0, 121mph |
|
02-12-2013, 10:46 PM | #405 |
Scooby Guru
Member#: 195711
Join Date: Nov 2008
Chapter/Region:
MWSOC
Location: Lapeer MI
Vehicle:PART OUT. PM ME 02-07 Goodies |
Interesting - thanks! Guys at work said the higher the tongue the better too.
I hope I don't have to tear bumper off. That would be a pain!! Its going to sit at P&L for a week and I don't know how secure their perimeter is. The trailer I have is similar to yours though so I might have to. Weekend project. |
02-12-2013, 10:52 PM | #406 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
At this point I just have a couple of the push style quick connects in the center of the bumper and then the connects on the fenders/side of front bumper. Comes on and off in 2 minutes.
|
02-13-2013, 08:34 AM | #407 |
Scooby Guru
Member#: 195711
Join Date: Nov 2008
Chapter/Region:
MWSOC
Location: Lapeer MI
Vehicle:PART OUT. PM ME 02-07 Goodies |
That's pretty slick. Am I over thinking that?
|
02-13-2013, 10:32 AM | #408 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
Over thinking? Probably.
I do that a lot... |
02-13-2013, 10:39 AM | #409 |
Scooby Guru
Member#: 32669
Join Date: Feb 2003
Chapter/Region:
SCIC
Location: Woodland Hills
Vehicle:2007 2.34LR, EFR7670 LINK G4+ hybrid STi |
Yes you are over thinking it. Instead of putting all the stock plastic clips on just use a few. Right now my entire front bumper is held on by 8 clips
|
02-13-2013, 10:46 AM | #410 |
Scooby Guru
Member#: 195711
Join Date: Nov 2008
Chapter/Region:
MWSOC
Location: Lapeer MI
Vehicle:PART OUT. PM ME 02-07 Goodies |
I will have to figure out another way to secure the wheel well liners.
I should stop being a cheap ass and buy some 06/07 liners so that It fits in there. I also need to get my headlights out to get the lowbeams working. Lotsa little stuff to do yet before Sunday night. Sorry for the sidetrack CJ. |
02-13-2013, 11:13 AM | #411 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
This thread is all over the place anyways. No worries.
|
02-13-2013, 11:28 AM | #412 |
Scooby Specialist
Member#: 73932
Join Date: Nov 2004
Chapter/Region:
RMIC
Location: Denver
Vehicle:2005 STi EFR 6758 04 S2000 EFR 7064 |
|
02-18-2013, 06:28 PM | #413 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
Got my clutch last week. Looking pretty good compared to the stock clutch that I pulled out.
vs. and due to an issue with the flywheel here she sits until next weekend... Just to make sure we get the car to stick I ordered a set of these today as well Last edited by C J; 02-18-2013 at 07:50 PM. |
02-18-2013, 07:21 PM | #414 |
Scooby Guru
Member#: 195711
Join Date: Nov 2008
Chapter/Region:
MWSOC
Location: Lapeer MI
Vehicle:PART OUT. PM ME 02-07 Goodies |
Damn clean garage.
I think I will need some racing tires for my final mod also. Looking good CJ |
02-18-2013, 07:48 PM | #415 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
It was pretty clean until I tore the car apart ha. Now it just smells like gear oil.
|
02-24-2013, 11:09 PM | #416 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
All back together. Quick picture of the engine bay. Installed the catch can, GM IAT sensor, and relocated the coolant reservoir. Still ugly lol.
|
02-24-2013, 11:19 PM | #417 |
Scooby Guru
Member#: 159243
Join Date: Sep 2007
Chapter/Region:
Tri-State
Location: medford nj 08055
Vehicle:5/01 bugeye Hakt Ecu is back! |
Looks way better than my mess.
|
02-24-2013, 11:25 PM | #418 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
Sometimes I swear there is just no pretty way to run some of these lines. If I try to tuck them under they end up binding or just not cooperating. PITA.
|
02-25-2013, 12:15 AM | #419 |
Scooby Specialist
Member#: 167338
Join Date: Dec 2007
Chapter/Region:
TXIC
Location: Texas
Vehicle:11 Wrx hatch Dgm |
|
02-25-2013, 12:32 AM | #420 |
Scooby Specialist
Member#: 73932
Join Date: Nov 2004
Chapter/Region:
RMIC
Location: Denver
Vehicle:2005 STi EFR 6758 04 S2000 EFR 7064 |
Getting there!
|
03-12-2013, 06:47 PM | #421 |
Scooby Specialist
Member#: 132587
Join Date: Nov 2006
Location: Lincoln, NE
Vehicle:2006 JrTuned STi 8.69@164mph |
It is time. TX2K13...who else am I going to see down there?
Show the EVOs this view |
03-12-2013, 07:18 PM | #422 |
Scooby Guru
Member#: 170602
Join Date: Jan 2008
Location: j-ville fl
Vehicle:06 Wrx RWD Auto 76MM-AEM-2200's |
dang car looks great man!! gotta love the counter clockwise fmic routing. so glad i went that way on mine. engine bay looks great. tires too!
|
03-12-2013, 07:59 PM | #423 |
Scooby Guru
Member#: 64908
Join Date: Jun 2004
Chapter/Region:
Tri-State
Location: Tuning 8/9sec Subies all over
Vehicle:10.8 XT+9.2@155 GR+ 9.1/157mph 2015 STI |
M&H represent!
|
03-12-2013, 08:01 PM | #424 |
Scooby Guru
Member#: 170602
Join Date: Jan 2008
Location: j-ville fl
Vehicle:06 Wrx RWD Auto 76MM-AEM-2200's |
hopefully he gets some clean passes and logs to check out.
|
03-12-2013, 08:09 PM | #425 |
Scooby Guru
Member#: 64908
Join Date: Jun 2004
Chapter/Region:
Tri-State
Location: Tuning 8/9sec Subies all over
Vehicle:10.8 XT+9.2@155 GR+ 9.1/157mph 2015 STI |
I will be there to make sure he does lol
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2007/2008 STI = Same R180 ? experts please! | Team Scream | Transmission (AT/MT) & Driveline | 9 | 05-21-2013 03:02 PM |
2006 Forester E85 / Mustang Dyno | PoZeR | Proven Power Bragging | 8 | 06-29-2011 03:51 PM |
FS : 2006 Aspen White STI (Ready for E85 conversion) | biker921 | Private Vehicle 'For Sale' Classifieds | 0 | 08-08-2010 10:43 AM |
Cheap quiet RCA's please? Experts, please contribute. | ebeck | Car Audio, Video & Security | 20 | 11-29-2004 01:22 PM |