|
|
|
|
Thread Tools | Display Modes |
10-04-2003, 07:40 PM | #1 |
Scooby Specialist
Member#: 43988
Join Date: Sep 2003
Chapter/Region:
SCIC
Location: So. Cal.
Vehicle:2002 WRX WRB |
Philips HID 6,000K bulb and JDM Projectors RHD
i know there are a lot of these already, but i need information from Step 1. I just got every thing in today and i'm reading the instructions and it does not make any sense AT ALL. I've already read the other posts and i'm so freaking lost right now. where to start... i know these two are compatible with each other because i have seen posts where they show the working version and are loving every minute of it.
1) the balast connected for the Philips kit does not match the projector connection on the JDM. i've tried putting on the philips buld, but i have to take off the fastener and the environmental cover from the JDM for it to fit. 2) other posts mention some thing about a harness... what is the harness thing and what are you guys talking about? AHHAAHAH!!! 3) can't read japanese and the drawings make it look easier than it is. 4) you think a subaru dealership will do this for me? 5) if any one could post pictures of step by step that would help, but i know that's too much to ask for. so if any one knows any place in the canoga park, tampa, reseda, simi valley, moorpark, or even LA area that will do a good job and won't rip me off on labor, please post a reply because i'm about to let this HID thing feel my High Intensity Dump-in-the-trash... not literally but you get my point. spent too much money on these stuff.
* Registered users of the site do not see these ads.
|
10-05-2003, 10:00 PM | #2 |
Scooby Specialist
Member#: 12841
Join Date: Nov 2001
Chapter/Region:
SCIC
Location: jchattdesign.com
|
I have a similar set-up. With a Hids4less kit.
1st make sure you have the proper H1 HID bulbs. H1's do not use the typical clip and turn harness due to their small size. You should have 2 wires coming out of the bulb. 2nd- you will not be using the OE harness that goes through the cup. 3rd- you will need to drill or cut a hole large enough to slide the HID wire through and connect the bulb and ignitor/ballast. Use black Silicone to seal the hole around the wires. Removing the headlights makes the installation much easier. If you have time you can come down to the TGIM meet in Yorba Linda on Monday night, you can check out how I wired mine up. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FS:NJ:Sti ballasts with D2S bulbs and TSX projectors | lilneel12 | Tri-State Area Private Classifieds | 18 | 03-27-2007 09:42 AM |
FS:Sti ballasts with D2S bulbs and TSX projectors | lilneel12 | Exterior/Styling | 12 | 02-02-2007 10:22 AM |
BRIDE SEAT, JDM Ver 6 STI Cluster and JDM Ver 6 STI Seat | Lancer3d | Interior/Dressup/Audio & Security | 7 | 01-03-2007 12:30 PM |
JDM STi HID lights w/ bulbs and ballasts | scca03wrx | Private 'For Sale' Classifieds | 8 | 05-25-2006 12:15 PM |
which hid kit to use for jdm projectors ? | billy boi | Electrical & Lighting | 10 | 01-26-2005 09:27 PM |