Welcome to the North American Subaru Impreza Owners Club Thursday March 28, 2024
Home Forums Images WikiNASIOC Products Store Modifications Upgrade Garage
NASIOC
Go Back   NASIOC > NASIOC Technical > Service & Maintenance

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.







* As an Amazon Associate I earn from qualifying purchases. 
* Registered users of the site do not see these ads. 
Reply
 
Thread Tools Display Modes
Old 06-02-2005, 11:21 AM   #1
scooterforever
Scooby Specialist
 
Member#: 55011
Join Date: Feb 2004
Location: New England
Vehicle:
1999 Legacy Outback

Default Cleaning And Reattaching The IACV (Idle Air Control Valve)

I cannot stress highly enough that you should have a replacement gasket on hand before opening the IACV. Also, remember that the IACV is attached to coolant lines, so... it's not something you want to work on when the car is hot.

This post explains how to remove, clean and reattach the IACV (sometimes also referred to as simply the IAC). In addition to my own experience (and frustration) with idle problems, this post incorporates suggestions from Unabomber, Overdose, WRX03 and others. I am not a mechanic or WRX expert. This post is not intended to cover all potential idle problems, but is merely a summary of approaches that several NASIOC members have had success with in solving their specific idle problems. Your results may vary. Feel free to PM me with additional suggestions, edits or corrections. Warning: I would recommend having a replacement IACV gasket on hand before opening the IACV. See below.

What Is The IACV?

The IACV is the "Idle Air Control Valve," or more fully, the "Idle Air Control Solenoid Valve." The IACV directly affects idle conditions, RPM in particular. On cold starts, the IACV sends rpm's higher than on a warm start. Irregular idle conditions may be the result of a dirty IACV sensor. Limited discussion of the IACV is covered on page 36 of the DOHC Engine service manual (at least for the 2002 MY).

Where Is The IACV?

The IACV sits directly above the throttle body, and is affixed to the throttle body with two screws. The picture below shows the IACV. In this picture, I have replaced one screw (left lower corner) with a hex-socket cap screw, while the other screw (right upper corner) has been removed.


Indications and Symptoms

The IACV is exposed to the intake charge, and grime can build up from both (these are my assumptions) a. oil blow-by and b. any impurities that manage to escape the air filter. A dirty IACV appears to cause both too high idle rates and too low idle rates. In my case, RPMs dropped immediately to zero (car stalled) when stopped. I needed to brake torque at a stoplight to simply keep the engine running. My idle problem took some time to manifest, and first appeared and disappeared after one day in January 2005 (bought the car in March 2002). By April 2005 it had returned, and was dramatically worse.

Replacement Gasket

As stated at the beginning of this thread, you should order and have in hand a replacement gasket for the IACV before removing the IACV, which is why I am including the "replacement gasket" discussion before I include instructions on how to remove the IACV (see below).

The IACV gasket is fragile, but what is more frustrating is that it actually expands under vacuum/pressure and temperature. As a result, it is possible that the old gasket has expanded so much that it is impossible to get it back into position once you have removed the IACV. You cannot know the condition of the gasket before removal of the IACV, so a good safety precaution IMO would be to have a new gasket standing by just in case.

Here is the issue in properly reattaching the IACV (see below): the IACV separates coolant circulated in the throttle body from the intake charge. If you have a bad seal, you will get coolant in your intake. From postings of members who have experienced this, coolant in your intake will show up as white smoke out the exhaust. For members who have performed the throttle body bypass mod, a bad IACV seal would manifest itself as a boost leak.

The part number for the IACV gasket is 22659AA120. It cost me $6 from Exeter Subaru in NH in person, but I could probably have gotten it for less from subaruparts.com online.

This picture shows how the old gasket expanded over the left-side of the gasket housing. It also shows where I pinched off a section trying to reattach the IACV.



This picture shows how much larger the old gasket is compared to a fresh gasket.



Removing The IACV

The IACV is attached to the throttle body by two screws that are very soft. These are phillips-head screws with wide slots for a flat-head screwdriver. Given the softness of these screws, Unabomber has suggested removing these screws with a large flat-head and not a phillips-head screwdriver. I used a flat-head screwdriver, and managed to still take a small piece out of the top of one screw.

WRX03 has also found success with this screw removal technique: Attach a small pair of vise grips to the heads of the screws, just enough pressure to slightly indent the metal. Turn the vise grips along with turning a phillips-head screwdriver at the same time. It will break the screws loose with ease. If you're careful and your "small" vise grips have a flat section at the tip of the teeth, you can barely see the indention on the heads of the screws. Larger vise grips work but it easier to eat up the screws. The picture below demonstrates WRX03 "vice grip" technique.

-- I need to locate this picture and fix this link still --

Cleaning The IACV

NASIOC members have used several different techniques to successfully clean the IACV. I would break these into three categories:

a) Unabomber's alcohol and Q-tip approach
b) variations on Unabomber's technique using WD-40, carb cleaner, and throttle body cleaner in place of alcohol. Note: it has been reported that carb cleaner eats rubber gasket material; therefore, it may be less desirable of a cleaning solution for cleaning the IACV than other solvents. If the IACV gasket is damaged, the result may include a boost leak and coolant in the intake.
c) WRX03's gasoline technique
d) Subaru write-up submitted by Jon_in_CT: http://endwrench.com/images/pdfs/ISCSpring04.pdf

I myself have only used the alcohol technique. I have no direct experience with the other approaches.

Unabomber's rubbing alcohol and Q-tip approach
Quote:
Originally Posted by Unabomber
Clean with alcohol and Q-tips; it should take you 20 or so to do the job. Reinstall. Turn the car to the ON position, wait 10 seconds, then OFF. Repeat three times, then start your car. This is the advice I got when my idle messed up this weekend. It didn't work, but when I started the car saturday morning after sitting overnight, the idle was fine. My idle problems were too high of an idle and a wandering idle with the associated P1519 code. This is what I did and what fixed it and since it's a cake fix, you might try it as well. There was a surprising amount of gook inside the IAC. Makes me glad that I switched back to the stock paper air filter over my old Perrin foam unit. Cleaner > supposed performance gain.
I followed this approach with rubbing alcohol and also required about 20 Q-tips. The catch is that you need to apply the Q-tips gently. You do not want to scrub, but rather gently remove grime. After cleaning, I let the IACV air dry before reattaching.

Variations On A Theme

Other board members have substituted alcohol with WD-40, carb cleaner and throttle body cleaner with success.

WRX03's Gasoline Technique

WRX03 cleaned his IACV by inverting it and filling the cavity with gasoline, and letting the gasoline sit in the cavity for a time. I would assume that Q-tips could also be used to clean out grime that the gasoline did not dissolve. Here is a picture of WRX03's IACV after cleaning with gasoline. Note: this is much cleaner than mine was after I cleaned it with rubbing alcohol and Q-tips.



Reattaching The IACV And How To Replace The Stock Screws With Cap Screws

As indicated above, the screws used to attach the IACV to the throttle body are VERY soft. I stripped one when I was reattaching the IACV trying, and failing, to reuse my old gasket. Thanks to WRX03, who pointed out to me that the screws are 5 mm by 20 mm long, I went to Ace hardware and bought two M5 (5mm) 20 mm long cap screws with hex sockets. You can see one of these in the lower left of the first picture. The stock screws come with both a lock washer and a larger flat washer. I was unable (not sure how they got the flat washers on the screws to begin with) to remove the flat washers from the stock screws, so I used a small lock washer with each cap screw/bolt. I omitted using a flat washer with each cap screw/bolt, which meant that they were slightly longer than the stock configuration. That did not, however, prove to be a problem. This picture compares the stock screws to the new cap screws I used:



The torque specification for the stock screws is 2.1 foot-pounds. Not having a low-torque torque wrench, I used a small hand-held allen wrench until they cap screw/bolts were snug.

Seating And Sealing The Gasket

It is important that the IACV be properly sealed. As you can see from the pictures above, an improper seal will allow coolant from the throttle body coolant lines to flow INTO your intake. Assuming you are using a fresh gasket, insert the gasket in the gasket grooves on the top of the IACV. As explained by Overdose in other posts, the gasket will look slightly too small. This is normal, and it will expand with heat, time and vacuum. Here is a shot of the new gasket ready to go:



Once the gasket was in place, I closed the IACV back onto the throttle body (see the next section below on reattaching the IACV). After the two bolts (I replaced the screws) had been torqued down, I reset the ECU (the manual says to do this; not sure if it is necessary, but figured it would not hurt). I then primed the fuel pump 3 times, for two seconds each time (I read this as part of Unabomber's IAC cleaning instructions). I started the car, and let it idle for about 10 minutes. This allowed the gasket to slowly heat up with the throttle body.

Following good advice from Overdose, I then took the car on a 10-mile freeway drive staying off boost, which is harder than you might think. Our cars really want to stretch their legs at all times. But I wanted the engine bay to get warm with highway-rpm's (yes, it was flush with highway-speed-airflow, but anyway***8230;) while the vacuum of running without boost would force the IACV gasket to expand.

After driving for 10 miles, I stopped and let the car idle for another 5 minutes. I checked the IACV for any outside coolant leaks, and it appeared fine.

I then turned off the engine. After about twenty minutes I returned, then started the car up. I drove back to the freeway, and, to see if the gasket was now sealed, applied boost. Then I applied more boost. After each application, I looked out my rear view mirror for any tell-tale clouds of white smoke that would indicate coolant had entered my air intake. No smoke. I then slowed down a bit, and did a nice healthy WOT run. All was fine, and the gasket was seated.
* Registered users of the site do not see these ads.

Last edited by scooterforever; 02-05-2007 at 02:40 PM.
scooterforever is offline   Reply With Quote
Sponsored Links
* Registered users of the site do not see these ads.
Old 06-28-2005, 05:10 AM   #2
wrx5150
Scooby Newbie
 
Member#: 24689
Join Date: Sep 2002
Default

To late, dealer charger me amost $500 to replace it.
wrx5150 is offline   Reply With Quote
Old 07-01-2005, 10:54 AM   #3
djerickd
Scooby Guru
 
Member#: 3782
Join Date: Jan 2001
Chapter/Region: South East
Location: Tampa B*tch!
Vehicle:
02 WRX WFC#040
Clean on 19's

Default

Whoa! Good write up! bumping for all to see!
djerickd is offline   Reply With Quote
Old 07-09-2005, 08:17 PM   #4
Chigliakus
Scooby Newbie
 
Member#: 77525
Join Date: Dec 2004
Location: DFW, TX
Vehicle:
'02 GDA, '09 GR
'93 FD

Default

Good write up! One thing to add, Unibomber's 'large flat-head screwdriver' technique didn't work for me, my car has over 50k miles and the screws were really stuck. I used an impact screwdriver, which makes removal of the screws that secure the iac valve easy with no stripping or damage. I bought mine from Home Depot for $20 and it's useful for lots of things, you can use any 1/2" drive socket with it.

http://www.homedepot.com/prel80/HDUS...prod_id=169426
http://www.harborfreight.com/cpi/cta...emnumber=37530
Chigliakus is offline   Reply With Quote
Old 07-10-2005, 05:52 PM   #5
Amazake
Scooby Specialist
 
Member#: 9889
Join Date: Sep 2001
Chapter/Region: NESIC
Location: 12.94 best ET 105.58 best trap
Default

Excellent, I have already ordered my gasket but the heads up on the screws is appreciated.
Amazake is offline   Reply With Quote
Old 07-20-2005, 10:36 PM   #6
scooterforever
Scooby Specialist
 
Member#: 55011
Join Date: Feb 2004
Location: New England
Vehicle:
1999 Legacy Outback

Default

Well, looks like the site hosting my pictures has killed the links. I'll see if I can get them back up.
scooterforever is offline   Reply With Quote
Old 07-20-2005, 10:49 PM   #7
Unabomber
Big Ron
Super Moderator
 
Member#: 18062
Join Date: Apr 2002
Chapter/Region: MAIC
Location: I can save you a ton of cash
Vehicle:
on car parts so PM
me b4 j00 buy

Default

Boo! If you can't work it out, PM me and I'll shoot you my email and I'll host them.
Unabomber is offline   Reply With Quote
Old 07-21-2005, 03:09 PM   #8
-=Ice-T=-
Scooby Newbie
 
Member#: 30956
Join Date: Dec 2002
Default

I want to clean my IACV, but I need the pics. Hurry up and get them rehosted.
-=Ice-T=- is offline   Reply With Quote
Old 07-30-2005, 06:11 PM   #9
MYfirst00
Scooby Specialist
 
Member#: 22928
Join Date: Aug 2002
Chapter/Region: NESIC
Location: Fitchburg, MA
Vehicle:
2015 Legacy Limited
Lapis Blue

Default

Let Unabomber host em, I wanna see!
MYfirst00 is offline   Reply With Quote
Old 08-01-2005, 01:51 AM   #10
Fat Tits
Scooby Specialist
 
Member#: 27046
Join Date: Oct 2002
Chapter/Region: Tri-State
Location: NYC
Default

Pics please!

this would be a huge help, this has been a PITA since Jan.. been to the dealer 4 times, each being "fixed" on my legacy.. morons.

thank you.
Fat Tits is offline   Reply With Quote
Old 08-03-2005, 09:52 PM   #11
kspek
Scooby Specialist
 
Member#: 32280
Join Date: Jan 2003
Chapter/Region: BAIC
Location: California
Vehicle:
07 STi Limited

Default

the large screwdriver didnt work for me either haha. need to invest in a impact screw driver now.
kspek is offline   Reply With Quote
Old 08-09-2005, 05:35 PM   #12
bren wrx
Scooby Guru
 
Member#: 59454
Join Date: Apr 2004
Chapter/Region: NESIC
Location: Worcester
Vehicle:
'10 E92 M3 M-DCT
brentuning.com/blog

Default

since one of my screws wouldnt come off, i tried another way, i seafoamed the car through the bov return line well and then since i did the TB bypass line i sprayed carb cleaner directly in there, let it sit, then sprayed some more in with the motor running and revving, seemed have cleared everything up
bren wrx is offline   Reply With Quote
Old 08-16-2005, 01:31 PM   #13
illmatic
Scooby Specialist
 
Member#: 3536
Join Date: Jan 2001
Chapter/Region: SCIC
Location: SD, OC
Vehicle:
2017 SWP BRZ PP, FXT
2002/2003 AW/PSM WRX

Default

+1 for the pics. I need to do this asap.
illmatic is offline   Reply With Quote
Old 08-16-2005, 05:31 PM   #14
SAINTSOFSPEED
Scooby Newbie
 
Member#: 40596
Join Date: Jul 2003
Chapter/Region: SCIC
Location: San Diego, CA
Vehicle:
03 WRX
MBP

Default

Good Job. I wished this post was written sooner, but I accomplished it the same way it was written. Carb Cleaner was good enough for me and my car has been running perfect since then...
SAINTSOFSPEED is offline   Reply With Quote
Old 08-20-2005, 07:01 PM   #15
scooterforever
Scooby Specialist
 
Member#: 55011
Join Date: Feb 2004
Location: New England
Vehicle:
1999 Legacy Outback

Default

Pics are back up! Sorry some of them are oversized -- I'll try to get them resized and re-edit the links, but at least they're up.
-- Scooter
scooterforever is offline   Reply With Quote
Old 09-10-2005, 11:21 PM   #16
Amazake
Scooby Specialist
 
Member#: 9889
Join Date: Sep 2001
Chapter/Region: NESIC
Location: 12.94 best ET 105.58 best trap
Default

FYI my IACV was spotless thanks to the alcohol injection.

We also used an impact screwdriver to remove the screw.
Amazake is offline   Reply With Quote
Old 09-15-2005, 01:36 PM   #17
Jon [in CT]
*** Banned ***
 
Member#: 2992
Join Date: Nov 2000
Chapter/Region: NESIC
Location: Connecticut, USA
Vehicle:
02 WRX Sedan
Silver

Default

Why not follow the procedure recommended by Subaru?
http://endwrench.com/images/pdfs/ISCSpring04.pdf
Jon [in CT] is offline   Reply With Quote
Old 11-06-2005, 10:29 PM   #18
ugetworked311
Scooby Newbie
 
Member#: 39792
Join Date: Jul 2003
Location: St.Louis
Default

Quote:
Originally Posted by Jon [in CT]
Why not follow the procedure recommended by Subaru?
http://endwrench.com/images/pdfs/ISCSpring04.pdf

Has anyone tried this one?
ugetworked311 is offline   Reply With Quote
Old 11-20-2005, 02:00 AM   #19
hitman912
Scooby Specialist
 
Member#: 38811
Join Date: Jun 2003
Chapter/Region: BAIC
Location: Watsonville and Sacramento
Vehicle:
2002 WRX Sedan
Platinum Silver

Default

nice.
hitman912 is offline   Reply With Quote
Old 11-30-2005, 09:48 AM   #20
All4bSpinnin
Scooby Guru
 
Member#: 99102
Join Date: Oct 2005
Chapter/Region: South East
Location: Jax, FL
Vehicle:
17 BMW M2
Long Beach Blue 6MT

Default Aahhhhhhhhhhhhhh!!!

dang! ive tried cleaning mine like 3 times and the idle is still stayin at like 1500 and surging to 2000... its really annoying.

i priced a IACV at Subaru of Jacksonville and they said 310$ ouch!

i guess i'll have to pay since this part is only covered under the 3/36000 warranty and im at 46 or so....

on the other hand it may not even be the IACV... here's my situation.

my car is a stage 4 and its been running on basemaps since i bought it...
my 4-wire 02 sensor had one wire frayed and not connected when my tranny popped. we rebuilt the tranny and reconnected that wire on my 02. (the car was down for a little over a month with the intercooler off). when we finally got the tranny back in it started doin this idle nonsense! so its either the UTEC makin it idle funny or the IACV??? what do you guys think???
All4bSpinnin is offline   Reply With Quote
Old 11-30-2005, 09:59 AM   #21
Mulder
Trust no one
Moderator
 
Member#: 11170
Join Date: Oct 2001
Chapter/Region: Tri-State
Location: NYC
Vehicle:
02 RAV4 MT
15 WRX/11 CRZ

Default

Not enough information to give you a definite answer. I wouldn't recommend spending the $300 for a new IAC on speculation.
Perhaps you can arrange to borrow one from someone to see if it helps or not?
I would also suggest replacing the 02 if the wiring is damaged since it's a critical component for maintaining proper A/F. Although it's also an expensive part I wouldn't hesitate here since it's already damaged.
Do you have any CELs? It would be helpful to hook up a scanner, or preferably a Delta Dash, and see what data is coming back from the various sensors.
Mulder is offline   Reply With Quote
Old 12-25-2005, 12:18 PM   #22
Charlie-III
NASIOC Supporter
 
Member#: 30669
Join Date: Dec 2002
Chapter/Region: Tri-State
Location: USA, North NJ, 07456
Vehicle:
1998 Legacy 2.5GT
Silver Sleeper BK, 5MT

Default

Quote:
Originally Posted by Jon [in CT]
Why not follow the procedure recommended by Subaru?
http://endwrench.com/images/pdfs/ISCSpring04.pdf
I can't use that one, I have a 98 which is a MAF. Besides, my IAC looks different than those posted here.
Mine has the Teflon coated (it's a green coating) rotary valve inside.

This thread is a well done thread for those that can use it though.
Charlie-III is offline   Reply With Quote
Old 01-17-2006, 01:34 AM   #23
specialev
Scooby Specialist
 
Member#: 90156
Join Date: Jun 2005
Chapter/Region: NWIC
Location: Auburn, Wa
Vehicle:
1986 Syncro Vanaru
07 SV650

Default

Is there anything in the IACV that would be damaged by cleaning it with Toluene or Acetone?
specialev is offline   Reply With Quote
Old 01-20-2006, 12:40 AM   #24
Chigliakus
Scooby Newbie
 
Member#: 77525
Join Date: Dec 2004
Location: DFW, TX
Vehicle:
'02 GDA, '09 GR
'93 FD

Default

Quote:
Originally Posted by specialev
Is there anything in the IACV that would be damaged by cleaning it with Toluene or Acetone?
Probably not, toluene is used as an additive in normal pump gas. The plastics used in the IAC valve have to be resistent to petrolium-based solvents. As long as I'm posting to this thread I should say I tried all kinds of stuff with my IAC valve, including cleaning it like in this thread several times with different solvents, and in the end had to replace it to fix my idle problems. Still worth a try though in my opinion.
Chigliakus is offline   Reply With Quote
Old 01-21-2006, 05:08 AM   #25
overdose
Scooby Specialist
 
Member#: 46399
Join Date: Oct 2003
Chapter/Region: MWSOC
Location: Grand Rapids, MI
Vehicle:
0000 Knows nothing,
about nothing.

Default

this gasket and it's proper replacement is BY FAR one of the most irritating features of the WRX, thank GOD my sti is dbw!
overdose is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
WTB: IACV (Idle Air Control Valve) JasonF Private 'Wanted' Classifieds 1 07-29-2009 01:40 PM
WTB IACV (Idle Air Control Valve) Tical Private 'Wanted' Classifieds 2 05-22-2009 02:31 PM
wtb- IACV (Idle Air Control Valve) BrettS Private 'Wanted' Classifieds 2 05-03-2006 10:57 AM
IACV Idle Air Control Valve jvcastillo21 Private 'Wanted' Classifieds 6 02-10-2006 10:02 PM
How To Replace The IACV Gasket (Idle Air Control Valve) scooterforever Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) 10 04-21-2005 05:52 PM

All times are GMT -4. The time now is 04:12 PM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2024 Axivo Inc.
Copyright ©1999 - 2019, North American Subaru Impreza Owners Club, Inc.

As an Amazon Associate I earn from qualifying purchases.

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission
Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.