|
|
|
|
Thread Tools | Display Modes |
|
02-26-2008, 08:22 PM | #1 |
Scooby Newbie
Member#: 41097
Join Date: Aug 2003
Chapter/Region:
SCIC
Location: Riverside, CA
Vehicle:2005 WRX Aspen White |
STi cluster swap FAQ - can we get one started?
I've noticed recently that there are numerous threads being started for STi cluster swaps. I think we should compile all the information for swaps into one thread so that it would be easier for people to find information and also cut down on posts asking for the same info.
Those of you that have done swaps, please post down what year STi cluster you used and what year WRX it went into as well as what modifications you had, any indicator lights which remained on, or any other notes which you deem were important. I'll check this thread periodically and edit my post to incorporate posts in this thread which contain information on swaps, giving credit to those who submitted the posts. If anyone has a better idea on how to do this please give your input. DISCLAIMER: Swapping out clusters WILL void the warranty on your car! We assume no responsibility if your warranty gets voided. Swap clusters at our own risk! For those of you wishing to have your new cluster reprogrammed to show the mileage of your old cluster check out www.tacomaspeedometer.com. They will require you to send a notarized statement as to why you are getting the cluster reprogrammed. Here's some info from my own swap. 04 USDM STi cluster into 05+ WRX ---------------------------------- -Cluster plugs in without any modifications to the plugs. -Outside air temp works ONLY on WRXs with auto HVAC. -Cruise indicator light wire must be moved from B28 to B16. -Illumination levels are set by pressing the odometer reset until "ill" appears in the odometer display. -Shift light and alarm are set by turning the set stalk on the left by the temp display. Note: I did not have any issues with any buzzing in my install. Some have reported their clusters buzzing. 06+ STi cluster users have reported the buzzing stopping after cutting wire C9. Indicator lights which remain on: -I/C waterspray: tape over or ground -Rear diff temp: tape over or ground -DCCD light: tape over -ABS: The ABS light will not work correctly since there is wiring differences in the ABS between the 04 and 05 models both on the car and in the cluster itself. I did some comparisons between the tech sheets on the 04 and 05 and the voltage the cluster sees between both years is reversed. Your ABS light will work "backwards" as in stay off for 2 seconds then turn on vs staying on for 2 sec and going out. It'll be annoying but you can put tape over the light. There's currently no known way to fix the ABS light problem with the 04 STi in 05 WRX setup. The only way would be to use an 05 STi cluster, but you'd end up moving more wires and having to modify one of the harness plugs in order for it to fit the STi cluster. Last edited by Okita Souji; 03-11-2008 at 04:57 AM. |
02-26-2008, 08:28 PM | #2 |
Scooby Newbie
Member#: 41097
Join Date: Aug 2003
Chapter/Region:
SCIC
Location: Riverside, CA
Vehicle:2005 WRX Aspen White |
Reserved for cluster pinout info
|
02-27-2008, 02:49 AM | #3 |
Scooby Newbie
Member#: 172977
Join Date: Feb 2008
Location: Northern California
Vehicle:2006 WRX TR |
05 USDM STI Cluster in 06 WRX TR
---------------------------------- -Illumination is the same as ^ -Shift light/buzzer same as ^ Modifications -Trimmed the left connector for it to fit -Clipped C9 located on the right connector(buzzer) -Moved B28 to B16 located on the center connector(cruise) -Ground B4 located on the center connector(diff light) Indicator Light -DCCD light remains on -Outside Temp Gauge doesn't work because I don't have auto HVAC The ABS has the correct polarity so the ABS light stays off. Last edited by BlueSubeDude; 02-29-2008 at 03:29 PM. |
05-11-2009, 08:55 PM | #4 | |
Scooby Newbie
Member#: 140641
Join Date: Feb 2007
Chapter/Region:
Tri-State
Location: Bronx NY
Vehicle:2006 Wrx Ltd. Wagon Urban Gry |
05STi cluster conversion to 06WRX limited
Quote:
WITH EXEPTION i did not ground b4 and did not clip C9 (just pulled pin out so no contact is made) DCCD lights up arrows off. WTF do I need arrows if I dont have diff control? But the rear DiFF TEMP Stays on. LOOKS Great! OAT shows as well. crappy cell phone pic Last edited by s3import; 05-11-2009 at 09:33 PM. Reason: Add-on Pic |
|
05-19-2011, 12:48 PM | #5 | |
Scooby Specialist
Member#: 230988
Join Date: Nov 2009
Chapter/Region:
NWIC
Location: The compound
Vehicle:2006 WRX SGM |
Quote:
|
|
10-22-2013, 02:01 PM | #6 | |
Scooby Newbie
Member#: 370527
Join Date: Oct 2013
Chapter/Region:
NWIC
Location: OR
Vehicle:2006 Subaru WRX STi White |
Quote:
Is there a way to set up HVAC in the wrx TR? |
|
10-31-2013, 07:14 PM | #7 |
Scooby Newbie
Member#: 321496
Join Date: May 2012
|
Just did the swap in my 04 WRX and put in a V8 STI cluster. For the most part everything has been plug and play, just curious about a couple quick questions that I tried looking for in here but have yet to find.
1: Cruise control indicators are not working, cruise still works fine, but no lights when its on or set. Is there a way to fix this? 2: Rear diff temp and DCCD, sounds like I just need to ground out a wire to get rid of this? or is there even a way to install the sensor? If not, what wires to I cut? 3: Outside temp is displaying a temperature. Does this mean I do actually have a temp sensor in my car? Id love for it to be working and not have to do anything else to make it work. |
02-27-2008, 11:35 AM | #8 |
Scooby Specialist
Member#: 116355
Join Date: May 2006
Chapter/Region:
TXIC
Location: DFW
Vehicle:2004 Impreza STI bassboat JBP |
jdm v7 cluster does not work in 2004 STi
|
02-27-2008, 11:47 AM | #9 |
Scooby Newbie
Member#: 85396
Join Date: Apr 2005
Chapter/Region:
RMIC
Location: Windsor, CO
|
05 USDM STI Cluster into 04 WRX
--------------------------------- -Illumination is changed as described above -Shift light/buzzer functioned properly and adjusted normally My install required no modification at all in order for the cluster to function properly. There were only a few issues: -DCCD light remained on (didn't bother me) -Rear Diff Temp Light remained on (since the wiring harness that connects to the cluster is different from the WRX to the STI, mine was missing a wire for pin B4 that needed to be grounded in order to shut this light off) -The Outside Temp display showed "--". I even tried to wire up the sensor and simulate the presence of the Auto A/C control module using a write up which can be found on ScoobyMods.com. Needless to say this did not work. Other than that there were no issues, no buzzing, and all of the indicator lights worked correctly, including the Cruise light and the ABS light. I sourced the cluster brand new from SubaruWRXParts.com. |
02-28-2008, 02:27 PM | #10 |
Scooby Specialist
Member#: 98012
Join Date: Oct 2005
Chapter/Region:
SCIC
Location: THE NARD, CA
Vehicle:2006 Aspen White STi 2015 XV Limited - Orange! |
subscribed!
|
02-28-2008, 05:02 PM | #11 |
Scooby Newbie
Member#: 74547
Join Date: Nov 2004
Chapter/Region:
W. Canada
Location: Sherwood Park, Alberta
Vehicle:2005 WRX WR Blue |
Does any one else have odd readings from their STI gauges in their WRX. I have a 05 wrx with 06 sti guages. The fuel will never go to full just below, the temp never makes it quite to the middle of the normal like it used to, and checking with my GPS the speedo is off when it shows 100KPH the gps was showing about 92KPH. I have still got to check the tach.
|
02-29-2008, 03:57 AM | #12 |
Scooby Newbie
Member#: 149526
Join Date: May 2007
Chapter/Region:
NWIC
Location: portland metro area
Vehicle:2002 aps dr65 hybrid 9.1x1 built block/heads |
does anybody have the wiring diagrams for the 04 sti gauge cluster. i want to make the out side air temp gauge work in a 02 wrx. i tryed this http://www.scoobymods.com/forums/sho...ight=sti+gauge but it doesnt work. so now im going to map it out from scratch. if some one has the diagrams please send them to [email protected]\. i'd love to contribute this to the community
also. i have a 04 cluster in a 02 wrx. i ran a wire to the outside rear of the car and hooked up the rear diff censor. that made the light go away. the speed is off in mine as well but it may be from using a 5 speed speed censor in a 6 speed gear box(broke the one from the 6 speed) |
02-29-2008, 02:23 PM | #13 |
Scooby Specialist
Member#: 98012
Join Date: Oct 2005
Chapter/Region:
SCIC
Location: THE NARD, CA
Vehicle:2006 Aspen White STi 2015 XV Limited - Orange! |
im putting a 05STi cluster in my 05wrx. im going to follow BlueSubedude's post , ill let you know if it all works! anything else i need to do to make it work?
thanks! |
02-29-2008, 03:26 PM | #14 | |
Scooby Newbie
Member#: 172977
Join Date: Feb 2008
Location: Northern California
Vehicle:2006 WRX TR |
Quote:
Also, I reprogrammed the STI cluster to match my current mileage. Good luck. |
|
02-29-2008, 03:40 PM | #15 | |
Scooby Specialist
Member#: 98012
Join Date: Oct 2005
Chapter/Region:
SCIC
Location: THE NARD, CA
Vehicle:2006 Aspen White STi 2015 XV Limited - Orange! |
Quote:
cool, where did you get the odo reprogrammed, i was think tacoma speedometer or somewhere local around me. i dont have the cluster yet but i should be picking it up tomorrow. thanks for all you help!!! |
|
09-24-2008, 10:43 PM | #16 | |
Scooby Specialist
Member#: 110021
Join Date: Mar 2006
Chapter/Region:
SCIC
Location: Socal
Vehicle:2003 WRXSTi Silver |
Quote:
Installation of my 05 STi Cluster USDM in my 03 WRX.. |
|
09-25-2008, 07:32 PM | #17 | |
Scooby Specialist
Member#: 127976
Join Date: Oct 2006
Chapter/Region:
BAIC
Location: Bay Area
Vehicle:2006 WRX Wagon 6 spd White |
Quote:
I used Tacoma Speedometer to have the mileage on my 06 STI cluster to the actual mileage on my car, which they did. |
|
09-25-2008, 09:46 PM | #18 | |
Scooby Specialist
Member#: 110021
Join Date: Mar 2006
Chapter/Region:
SCIC
Location: Socal
Vehicle:2003 WRXSTi Silver |
Quote:
Yeah i heard.. i spoke with Tacoma and they i buy a new cluster from subaru.. they have to give me some kind of stamp to put on the door.. and i can just send Tacoma my Cluster with a Digital Picture of the Stamp or Sticker.. im going to call Subaru and ask.. |
|
09-26-2008, 12:05 AM | #19 | |
Scooby Specialist
Member#: 116105
Join Date: May 2006
Chapter/Region:
TXIC
Location: Dallas,TX
Vehicle:2001 Civic/2006 WRX Blue/Steel Grey Metallic |
Quote:
Ok guys.... Lets get one thing straight here. You can tamper with your odometer all you want. There is no law against you tampering with it. It's your car, you can do with what you want. Now, if you roll back the miles and try to sell the car without notifying the buyer...now it's a felony. |
|
02-29-2008, 03:33 PM | #20 | |
Scooby Newbie
Member#: 149526
Join Date: May 2007
Chapter/Region:
NWIC
Location: portland metro area
Vehicle:2002 aps dr65 hybrid 9.1x1 built block/heads |
Quote:
so if someone has the diagrams for the cluster, please send them to [email protected] \ thanks, mike |
|
02-29-2008, 03:35 PM | #21 |
Scooby Guru
Member#: 59993
Join Date: Apr 2004
Chapter/Region:
International
Location: WWAAYY west of the Mississippi
Vehicle:Ass, grass or cash no one rides for free!! |
great thread. let's get more info and pics in here.
|
02-29-2008, 09:56 PM | #22 |
Scooby Newbie
Member#: 149526
Join Date: May 2007
Chapter/Region:
NWIC
Location: portland metro area
Vehicle:2002 aps dr65 hybrid 9.1x1 built block/heads |
ok, i have the cluster dimming with out a external potentiometer. ill get a vid up of it soon, also not to keep bugging about the wiring diagrams but this would be so much easyer if i had them. i will get all the option on this fully functional including dccd ligh off(if equipt) and the dccd lights to scroll with the thumb wheel. out side temp censor will be working soon too. just want it to go faster thats all, and the diagrams help so much.
p.s. strang thing about the out side temp. i had it working but after about 2 ours it stopped, i think i have a bad oem censor. |
03-01-2008, 02:53 AM | #23 |
Scooby Newbie
Member#: 149526
Join Date: May 2007
Chapter/Region:
NWIC
Location: portland metro area
Vehicle:2002 aps dr65 hybrid 9.1x1 built block/heads |
http://media.putfile.com/sti-cluster...dimmer-working
here is a vid of the dimmer working w/out a potentiometer |
03-01-2008, 03:19 AM | #24 |
Scooby Newbie
Member#: 149789
Join Date: May 2007
|
2007 STi Cluster in a 2007 WRX
|
03-01-2008, 03:25 AM | #25 | |
Scooby Newbie
Member#: 149526
Join Date: May 2007
Chapter/Region:
NWIC
Location: portland metro area
Vehicle:2002 aps dr65 hybrid 9.1x1 built block/heads |
Quote:
|
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
can we get some mods to start deleting duplicate threads? | [27] | Political Playground - Chaotic Neutral Edition | 2 | 11-05-2008 02:01 AM |
STi hare emblem? where can i get one... | evoeater8 | Interior & Exterior Modification | 13 | 07-12-2006 08:53 PM |
can we get something started in RDU???(nc) | imprezivSTi04 | Mid Atlantic Impreza Club -- MAIC | 3 | 04-04-2006 06:47 PM |
02 sti hood scoop?? where can i get one? | slaterdrew | Private 'Wanted' Classifieds | 2 | 02-06-2004 11:37 AM |
lighted keyhole ring, can we get one? | makanouchi | Interior & Exterior Modification | 12 | 11-22-2002 08:38 PM |