|
|
|
|
Thread Tools | Display Modes |
08-17-2011, 09:44 PM | #26 |
Scooby Newbie
Member#: 57387
Join Date: Mar 2004
Chapter/Region:
SCIC
Location: Orange county
Vehicle:02 wrxwagon PSM |
I will give this a ry as I am having exact same problem...
02 wrx old tactrix cable...bought 5 years ago, maybe six. hoping this works It seems like I can logg car...I even pulled out wifes 02 sony laptop with ancient versions of everything on it...same problemo.
* Registered users of the site do not see these ads.
|
08-18-2011, 09:54 AM | #27 |
Scooby Guru
Member#: 70395
Join Date: Sep 2004
Chapter/Region:
MAIC
Location: Da-boonies,Va
|
It can also be a timing issue. The second I turn the ignition key to on I am hitting the second flash prompt from Ecuflash.
|
08-18-2011, 11:27 AM | #28 |
Scooby Specialist
Member#: 158029
Join Date: Aug 2007
Chapter/Region:
MAIC
Location: Shippensburg, PA
Vehicle:2017 Jeep Wrangler Firecracker Red |
Try EcuFlash 1.29a. It may be too old to be deemed "authentic" with the newer versions. I think the 1.3u and the 2.0 are the only cables that work with the newer versions.
|
08-18-2011, 09:44 PM | #29 |
Scooby Newbie
Member#: 57387
Join Date: Mar 2004
Chapter/Region:
SCIC
Location: Orange county
Vehicle:02 wrxwagon PSM |
Well guys,
I have seemingly tried it all...uninstalled 1.42, installed 1.29 I have tried 1.30... Just this stuff just not work on 02 wrx? I have read alot of these post, funny enough, after I decided to go this route, and not just have cobb, or road race do what I needed...man do I feel like an a Sorry guys, burst of frustration... I have researched this alot and find these same "denso02_bootloader_cmd error posts", but yet have I found an exact answer, so I will itemize what I have tried based on a few seperate posts, and what in my case has not worked. 1. 02 wrx w/ tactrix cable...its 2005 version 2. have tried 2 seperate computers 3. tried ecuflash v1.42, v1.30, v1.29a 4. tried all different usb ports on both computers 5. double, triple checked blue dongle / reflash connector 6. double checked green test connectors To date, I still get denso02_bootloader_cmd error Last edited by cbean; 08-18-2011 at 10:45 PM. |
08-24-2011, 11:58 AM | #30 |
Scooby Specialist
Member#: 1366
Join Date: Apr 2000
Chapter/Region:
VIC
Location: Delta, BC, Canada
Vehicle:2000 RS-T -> RSTi-8 Blue Ridge Pearl |
And you can't verify that your ECU hasn't been "touched" with Cobb AP or EcuTEK? I'm in the same boat - no signs suggesting that it was tuned with EcuTEK (JDM STi Ver8 ECU) but getting the same error. However, my test mode connector, while it is wired, doesn't bring on test mode and still couldn't find the test mode connect on the passenger side
|
08-24-2011, 03:39 PM | #31 |
Scooby Newbie
Member#: 23659
Join Date: Aug 2002
Chapter/Region:
HIIC
Location: Kailua Kona HI
Vehicle:2002 WRX Sport Wagon Platinum Silver |
A 1.3S cable works fine on my 02. Absolutely clean connect. The one time I had issues, the green test connectors were not seated well. Verified this by noting no test cycle. I always let the fans cycle now to verify good connections. No idea how picky the timing to key on is, but it has yet to miss as I do it in less than 1 second.
A screenshot from before shows ECUFlash did not see the cable, otherwise is would show in the lower right. You are p**ing upwind until you get that fixed. Either bad driver setup, or bad cable. |
12-31-2014, 06:01 PM | #32 |
Scooby Newbie
Member#: 257982
Join Date: Sep 2010
Chapter/Region:
Tri-State
Location: Columbus, Ohio
Vehicle:02 Impreza Aspen White |
im having the same exact problem. installing the ECU into another WRX temporarily allowed me to dump/write the ECU with no problems. maybe you are having a similar issue as me. has this been resolved?
i could datalog as well |
01-01-2015, 05:41 PM | #33 |
Scooby Specialist
Member#: 267815
Join Date: Dec 2010
Chapter/Region:
South East
Location: LSx allll done..need headers
Vehicle:Be in awe dont hate .) |
02s are the trickiest......if your cables are good then your timing is off. As soon as you turn on the key....hit the connect prompt. At the exact same time. My 04 STi only works with key on...count to one...click the mouse..done. a full second difference. We went through everything and were just turning the key a sec before we prompted it to read lol
|
01-01-2015, 05:45 PM | #34 |
Scooby Specialist
Member#: 267815
Join Date: Dec 2010
Chapter/Region:
South East
Location: LSx allll done..need headers
Vehicle:Be in awe dont hate .) |
And is the Romdata directory setup correctly? Your screenshot shows 0 models read....I cant remember if that's right. I haven't flashed the old Motorola im a year or so lol
Last edited by Paidfor; 01-01-2015 at 05:46 PM. Reason: okkk |
01-01-2015, 09:31 PM | #35 |
Scooby Newbie
Member#: 316863
Join Date: Apr 2012
Chapter/Region:
E. Canada
Location: Southern Ontario
Vehicle:2001 2.5RS Red |
On my 03wrx , the same as 02 for flashing, if I turn the key and hit the start button at the same time, it DOES NOT work. I have to hit the start button and wait for around 1/2 sec to a full sec before turning the key on for it to work.
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
cant read or write ecu | carlosdevil10 | Open Source Reflashes | 11 | 12-28-2010 02:53 PM |
Won't read or write to ECU.......Interface close. HELP! | bertune | Open Source Reflashes | 10 | 08-28-2010 09:06 AM |
cant read or write with ecuflash, but... | crxgator | Open Source Reflashes | 2 | 06-22-2009 12:45 PM |
FS or trade: 2002 WRX Aspen White | cmarshall259 | Private Vehicle 'For Sale' Classifieds | 76 | 04-27-2007 09:29 AM |
FS: OR (oregon) 2002 WRX steering wheel | tokstad | Private 'For Sale' Classifieds | 2 | 06-03-2006 10:33 AM |