|
|
|
|
Thread Tools | Display Modes |
05-01-2010, 10:53 PM | #1 |
Scooby Specialist
Member#: 101865
Join Date: Nov 2005
Chapter/Region:
NWIC
Location: Covington, WA
Vehicle:88 GL-10 STi silver |
First start-up EJ Hybrid
Specs:
2005 EJ257 Block, crank, rods 1997 STI EJ20K Heads (Pollished Intake Ports) JE Deep Dish Pistons\ STI Head Gaskets / will give me 8.75:1-8.80:1 compression ratio 1997 STI EJ20K Cams 1996 EJ20G intake manifold (ported and painted) and wiring 1996 EJ20H Timing Belt Covers 2003 EJ207 VF37 Twin Scroll Turbo 1" Intake Spacers to allow front inlet turbo Phenolic intake spacers EJ20K Power Steering Pump ViPEC standalone ECU (Currently in the car) ARP Head Studs Gates HP Timing Belt Excedy Twin Disc clutch Custom Built -6 AN Parrallel Fuel Rails Sard Fuel Pressure Regulator Video: now i just have to weld up the downpipe. get a "T" for the PCV to the chetch can and work on the idle... then drive it, brake it in, and tune it... -=Suberdave=-
* Registered users of the site do not see these ads.
|
05-03-2010, 10:28 PM | #2 |
Scooby Specialist
Member#: 123362
Join Date: Aug 2006
Chapter/Region:
MWSOC
Location: Dorothy's House
Vehicle:'97 E36 M3 351W FTW |
Very nice. I'm putting the finishing touches on my EJ205 engine (forged pistons, STi rods, +1 bearings) with Ver4 STi heads (no porting). A couple of dumb questions,
What coils are you using (assuming USDM)? Plugs? Lastly, where did you get the spacers? I'm considering the HTA68, but have to address the stock inlet location and I'm not wild about the Samco 90 degree inlet kit. |
05-03-2010, 11:11 PM | #3 | |
Scooby Specialist
Member#: 101865
Join Date: Nov 2005
Chapter/Region:
NWIC
Location: Covington, WA
Vehicle:88 GL-10 STi silver |
Quote:
2. I am using one step colder NGK V-power BKR7E 3. the spacers were made by my father. i scaned a intake gasket and copied it into OMAX (drafting softwere) then my father cut them on a water jet. (if interested i have another set i would sell. PM me if interested...) -=Suberdave=- |
|
05-04-2010, 10:52 PM | #4 | |
Scooby Specialist
Member#: 123362
Join Date: Aug 2006
Chapter/Region:
MWSOC
Location: Dorothy's House
Vehicle:'97 E36 M3 351W FTW |
Quote:
|
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
First start up after winter storage question | Rallly2000 | Newbies & FAQs | 11 | 02-01-2010 06:16 PM |
02 wrx hybrid looking for a start up map | xcrament | Open Source Reflashes | 0 | 10-26-2008 11:40 PM |
RAW Performance Stg.5 First start up SUCCESS | oneoverWRX | Built Motor Discussion | 15 | 03-24-2008 01:00 AM |
Hybrid 1st Start Up | Rick539 | Built Motor Discussion | 1 | 10-28-2007 11:06 PM |
Hybrid misfire on start up | gnarlyWRX | Built Motor Discussion | 6 | 05-03-2007 10:15 AM |