|
|
|
|
Thread Tools | Display Modes |
05-06-2007, 12:54 AM | #1 |
Scooby Newbie
Member#: 136089
Join Date: Dec 2006
Chapter/Region:
Tri-State
Vehicle:2003 WRX |
If I program a 2nd key fob will the original still work??
when i bought my car it only came with one set of keys.. i want a backup keyfob for the 2nd set i had made.. if i do this will the original fob still work?? or only one fob per car?? thanks for any help!
~Paul
* Registered users of the site do not see these ads.
|
05-06-2007, 09:17 AM | #2 |
Scooby Newbie
Member#: 143290
Join Date: Mar 2007
Chapter/Region:
E. Canada
Location: New Brunswick
Vehicle:2007 SE Wagon Obsidian Black Pearl |
Check your manual for model year specific information but I know I can have up to 4 different remotes (2007).
|
05-06-2007, 09:18 AM | #3 |
Scooby Guru
Member#: 120152
Join Date: Jul 2006
Chapter/Region:
MWSOC
Location: Indy
|
My car came with 2 fobs and 3 sets of keys (1 was a valet key).
|
05-06-2007, 09:19 AM | #4 |
GC84Ever
Super Moderator Member#: 301
Join Date: Sep 1999
Chapter/Region:
NWIC
Location: WA
Vehicle:1970 FF-1 & '70 Van 02 WRX/01 RS |
|
05-06-2007, 02:55 PM | #5 |
Scooby Newbie
Member#: 136089
Join Date: Dec 2006
Chapter/Region:
Tri-State
Vehicle:2003 WRX |
|
05-06-2007, 03:02 PM | #6 |
Scooby Specialist
Member#: 134610
Join Date: Dec 2006
Location: Cheraw, SC
Vehicle:2003 WRX SONIC YELLOW STG 4 |
I was given a 2nd key fob for mine that wasnt programmed, i programmed it and it worked just fine, and my original one works as well.
These are the instructions I used to program mine Round Remote Transmitter Programming Instructions 1. Disarm the security system (if so equipped). 2. Open the driver's door and sit in the driver's seat. 3. Close the driver's door. 4. Place the ignition key in the ignition switch and cycle the switch from "LOCK" to "ON" ten times within 15 seconds. Be sure to stop at the "LOCK" position and leave the key in the ignition when you are done. The horn will sound once to indicate that you are in transmitter programming mode. 5. You must finish the next steps within 45 seconds of the horn honking. 1. Open the driver's door. 2. Close the driver's door. 3. Press and release any button on the transmitter. The horn will sound two times to indicate that the transmitter has been programmed. 6. After programming your remote, remove the key from the ignition switch. The horn will sound three times to indicate the system is now out of programming mode. Ensure your remotes work properly at this time You may program up to four remotes at any one time. If you lose a remote, program the other four times to clear the code for the lost remote until you can replace it. Do not program your remotes with other Subarus in the vicinity- you may be unknowingly programming someone else's remote for your vehicle! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
programming an electronic key fob | corgimas | Car Audio, Video & Security | 67 | 10-23-2019 09:02 AM |
Will I save cash If I import a 2nd hand STI from the U.S into Canada? | goldwave84 | General Community | 13 | 06-26-2007 06:59 AM |
Will This Clutch Still Work? | stimpy | Transmission (AT/MT) & Driveline | 5 | 08-14-2003 03:06 PM |
will my laptop still work???? | smacksube | South East Region Forum | 9 | 06-02-2003 05:03 PM |
Will my spare still Work w/17"'s? | WindyWRX | Brakes, Steering & Suspension | 6 | 10-17-2002 04:27 AM |