gc8 wrx exhaust

preza · 10-11-2001, 01:18 PM

will a 3 inch exhaust made for the gc8 wrx fit a turbo'd 2.5 ?
will anything have to be modified ?

* Registered users of the site do not see these ads.

Kcz · 10-11-2001, 02:29 PM

Yes it will fit, but it's a little too long. I had a small section cut out of a stright peice of pipe.

jeffg · 10-11-2001, 04:17 PM

I think it depends on the kit. My WRX RA exhaust was way longer than the stock RS. It had a bend in the midpipe and continued past the rear cat. I think it would bolt directly to the down pipe on a WRX.

You might need to cut the midpipe to make it fit.

Jeff

TaiChih · 10-11-2001, 06:05 PM

Yes, you will have to modify, just get the 3" brullen exhaust for the RS from GTBGUY.

10-11-2001, 01:18 PM	#1
preza Scooby Specialist Member#: 1454 Join Date: May 2000 Location: Wyoming Vehicle: 2000 2.5 RS-T Blue	gc8 wrx exhaust will a 3 inch exhaust made for the gc8 wrx fit a turbo'd 2.5 ? will anything have to be modified ? * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS : Stock WRX Exhaust and STI Pocket	blue02scoobie	MAIC Private Classifieds	6	06-01-2010 09:09 PM
FS : Stock WRX Exhaust and STI Pocket	blue02scoobie	Engine/Power/Exhaust	1	06-01-2010 01:34 PM
WTT: GC8 Coilovers, WTT GC8/WRX 3" exhaust	ZeroDrift	NWIC Private Classifieds	5	08-22-2008 04:27 AM
GC8 EJ20K exhaust manifold VS US WRX exhaust manifld	keirnna	Factory 2.0L Turbo Powertrain	2	01-01-2008 04:40 PM
WTB GC8 WRX exhaust. turbo 2.5" or bigger	supermoose	Private 'Wanted' Classifieds	2	12-10-2003 05:01 AM

10-11-2001, 02:29 PM	#2
Kcz Scooby Newbie Member#: 2038 Join Date: Aug 2000 Location: Plano, Texas Vehicle: 2000 RS-T Silverthorn Metallic	Yes it will fit, but it's a little too long. I had a small section cut out of a stright peice of pipe.

10-11-2001, 04:17 PM	#3
jeffg Scooby Guru Member#: 2958 Join Date: Nov 2000 Chapter/Region: NWIC Vehicle: 2001 WRX (GC8)	I think it depends on the kit. My WRX RA exhaust was way longer than the stock RS. It had a bend in the midpipe and continued past the rear cat. I think it would bolt directly to the down pipe on a WRX. You might need to cut the midpipe to make it fit. Jeff

10-11-2001, 06:05 PM	#4
TaiChih Scooby Specialist Member#: 3467 Join Date: Jan 2001 Location: Odenton, MD Vehicle: 1998 Dinan3 Bleck	Yes, you will have to modify, just get the 3" brullen exhaust for the RS from GTBGUY.