axleback q, do i need a new gasket for an install?

Dash_Martino · 08-26-2006, 10:19 AM

Hey all, I'm picking up an SPT axleback for my RS. Will I need a new gasket between the midpipe/axleback?

* Registered users of the site do not see these ads.

05blkrs · 08-26-2006, 10:39 AM

most ppl will say dont worry about it but i say go ahead.. .. i'm a fan of NEVER reusing gaskets...

badtaste · 08-26-2006, 10:57 AM

^ditto

Dash_Martino · 08-26-2006, 12:43 PM

anybody got a part # on that one?

moogoob · 08-26-2006, 02:32 PM

yeah... its cheap and easy anyway. I always go for the new gasket. It beats getting everything apart, then having to run out for it again.

Sube0 · 08-27-2006, 11:01 AM

Good luck on the fitment. I bought an spt exhaust and the flanges were angled differantly, and completly differant. I had to cut the flange off my old exhaust, and rewld it to the new one. I was pissed that I had been jacked, so they through me a discount since I couldn't return it

Dash_Martino · 08-27-2006, 11:34 AM

does anyone have a part # for that axleback gasket??

svek · 08-28-2006, 05:04 AM

http://subaruwrxparts.com/04rs-drivetrain.html

third from the bottom

08-26-2006, 10:19 AM	#1
Dash_Martino Scooby Newbie Member#: 78728 Join Date: Jan 2005 Chapter/Region: Tri-State Location: Jim Chunk, PA Vehicle: 04 STi PSM	axleback q, do i need a new gasket for an install? Hey all, I'm picking up an SPT axleback for my RS. Will I need a new gasket between the midpipe/axleback? * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
do i need to resurface flywheel for an used clutch?	jacky599r	Transmission (AT/MT) & Driveline	4	05-07-2009 05:24 PM
Do i need a new gasket?	vnasty86	Newbies & FAQs	5	06-22-2007 04:44 PM
Do I need a new driveshaft for swaping an R160 to R180?	Rustyr6	Transmission (AT/MT) & Driveline	18	06-27-2005 07:32 PM
Do I need new gaskets for header install?	Silverandscared	Factory 2.0L Turbo Powertrain	11	09-19-2004 10:52 PM
Do I need a new ECU for '99 Legacy 4EAT->5MT	whtlegacy	Subaru Conversions	0	02-10-2004 01:41 PM

08-26-2006, 10:39 AM	#2
05blkrs Scooby Newbie Member#: 110343 Join Date: Mar 2006 Chapter/Region: TXIC Location: pendleton Vehicle: 2005 impreza 2.5RS black	most ppl will say dont worry about it but i say go ahead.. .. i'm a fan of NEVER reusing gaskets...

08-26-2006, 10:57 AM	#3
badtaste Scooby Newbie Member#: 116636 Join Date: Jun 2006 Chapter/Region: MWSOC Location: ohio Vehicle: 2003 impreza black	^ditto

08-26-2006, 12:43 PM	#4
Dash_Martino Scooby Newbie Member#: 78728 Join Date: Jan 2005 Chapter/Region: Tri-State Location: Jim Chunk, PA Vehicle: 04 STi PSM	anybody got a part # on that one?

08-26-2006, 02:32 PM	#5
moogoob Scooby Specialist Member#: 7101 Join Date: May 2001 Chapter/Region: Tri-State Location: Toms RIver Vehicle: 00RS I want to fill your mouth with spiders	yeah... its cheap and easy anyway. I always go for the new gasket. It beats getting everything apart, then having to run out for it again.

08-27-2006, 11:01 AM	#6
Sube0 Scooby Newbie Member#: 123724 Join Date: Aug 2006 Chapter/Region: RMIC Location: Lakewood Co Vehicle: 06 2.5i Steel grey	Good luck on the fitment. I bought an spt exhaust and the flanges were angled differantly, and completly differant. I had to cut the flange off my old exhaust, and rewld it to the new one. I was pissed that I had been jacked, so they through me a discount since I couldn't return it

08-27-2006, 11:34 AM	#7
Dash_Martino Scooby Newbie Member#: 78728 Join Date: Jan 2005 Chapter/Region: Tri-State Location: Jim Chunk, PA Vehicle: 04 STi PSM	does anyone have a part # for that axleback gasket??

08-28-2006, 05:04 AM	#8
svek * Banned * Member#: 82259 Join Date: Mar 2005 Chapter/Region: BAIC Location: koledge at csus Vehicle: 1999 impreza 2.2L Brilliant Red <4EAT Club>	http://subaruwrxparts.com/04rs-drivetrain.html third from the bottom