Anyone know if there is a local place that makes/repairs silicon hose?

DickWRX · 08-31-2006, 12:08 PM

Hey

Just wondering if anyone knows of a local place that makes silicone hoses or could repair a hose.

Cheers

Rich

* Registered users of the site do not see these ads.

DoctorNick · 08-31-2006, 12:18 PM

Depends on the damage and type of hose unfortunally. You might be better off getting a rubber hose and melt it over the puncture. But that prob won't hold to much pressure. If its a rip, your in trouble no matter what me thinks.

Samco hoses ftL!

P&L Motorsports Inc. · 08-31-2006, 12:23 PM

Its a hose from my MRT tmic, its not readily avaible...

Tim Sanderson · 08-31-2006, 01:39 PM

Last time I checked, silicone sticks to silicone.

Clean it, scuff it, and go buy a tube of silicone.

dntouch · 08-31-2006, 09:43 PM

Dick WRX.. I am guessing you are the guy i was speaking to at P&L.? I was there for a tune and we were pondering a couple different ideas for a new hose off the turbo..?

Good luck if it was you..

ChgoJay · 09-01-2006, 03:13 AM

Rich what hose are you talking about? Silicone is repairable. If they can make hoses they can fix them.

08-31-2006, 12:08 PM	#1
DickWRX Scooby Specialist Member#: 60590 Join Date: Apr 2004 Chapter/Region: MWSOC Location: Schaumburg	Anyone know if there is a local place that makes/repairs silicon hose? Hey Just wondering if anyone knows of a local place that makes silicone hoses or could repair a hose. Cheers Rich * Registered users of the site do not see these ads.

08-31-2006, 12:23 PM	#3
P&L Motorsports Inc. NASIOC Vendor Member#: 67199 Join Date: Jul 2004 Chapter/Region: MWSOC Location: Chicago Vehicle: 2007 8.99@160mph STI Carbon	Its a hose from my MRT tmic, its not readily avaible... Last edited by P&L Motorsports Inc.; 08-31-2006 at 02:31 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Does anyone know if there is a company that...	carguy19	Factory 2.5L Turbo Powertrain	5	07-15-2004 10:28 AM
Does anyone know if there is a lightened flywheel that weighs between 17-20 lbs?	2.2gotboost	Transmission (AT/MT) & Driveline	11	03-24-2004 06:13 PM
Anyone know if there is a cold air intake for 98 2.5	jin88	Normally Aspirated Powertrain	19	05-14-2003 04:40 PM
does anyone know if there is an actuall logo for the boxer motor ?	Maxtastic	Bay Area Impreza Club Forum -- BAIC	4	09-16-2002 11:33 AM
Does anyone know if there is a LATCH retro kit for the 99 Forester?	mooney	Forester Forum	1	09-11-2002 10:01 PM

08-31-2006, 12:18 PM	#2
DoctorNick NASIOC Supporter Member#: 7022 Join Date: May 2001 Chapter/Region: MWSOC Location: Chicago, Il. Vehicle: 2013 BRZ Limited SWP	Depends on the damage and type of hose unfortunally. You might be better off getting a rubber hose and melt it over the puncture. But that prob won't hold to much pressure. If its a rip, your in trouble no matter what me thinks. Samco hoses ftL!

08-31-2006, 01:39 PM	#4
Tim Sanderson Scooby Guru Member#: 6486 Join Date: May 2001 Chapter/Region: MWSOC Location: S.E. wisconsin Vehicle: 00 Impreza 2.5 RS Blue Ridge Pearl	Last time I checked, silicone sticks to silicone. Clean it, scuff it, and go buy a tube of silicone.

08-31-2006, 09:43 PM	#5
dntouch Scooby Specialist Member#: 79662 Join Date: Jan 2005 Chapter/Region: MWSOC Location: Germantown WI. Vehicle: 11 Jeep Unlimited White	Dick WRX.. I am guessing you are the guy i was speaking to at P&L.? I was there for a tune and we were pondering a couple different ideas for a new hose off the turbo..? Good luck if it was you..

09-01-2006, 03:13 AM	#6
ChgoJay Scooby Specialist Member#: 71722 Join Date: Oct 2004 Chapter/Region: MWSOC Location: Plainfield, IL Vehicle: 2004 WRX ZINGER!!!! WORLDRALLYPLATINUMBLING	Rich what hose are you talking about? Silicone is repairable. If they can make hoses they can fix them.