MY99 Intake (Again)

Surboo · 11-22-2001, 10:54 PM

I have been trying to figure out what to do with my intake on my 99 lately and have narrowed it down to several choices. Right now I am running a K&N cone filter with Kartboy MAF adapter and a carbon heat shield. Would I see any gains if I were to switch to a Weapon R tube with my K&N filter or a modified Accruit intake to work with the MAF? Between those two setups which one would be safer for the MAF? Which would be more powerful? Are there any pther things I should consider? BTW I do already have a S-AFC so the high rpm lean issues aren't a big concern. I know there has been MAF intake discusions before, but after searching I didn't find any thing other than DIY intakes. Thanks alot for any help.
-Brandon

* Registered users of the site do not see these ads.

Silverscooby27 · 11-23-2001, 12:02 AM

Hi,

I actually just installed a GanzFlow from Larry Ganz who is out in your neck of the woods. Check out his CAI, he makes one specifically for the MY99 Phase II motor. I haven't installed my S-AFC yet, but am trying to have it done.

DanzBorin · 11-23-2001, 12:14 PM

Check out this!

http://www.i-club.com/forums/showthr...threadid=93646

It's the only way to go!

Rob

11-22-2001, 10:54 PM	#1
Surboo Scooby Newbie Member#: 8721 Join Date: Jul 2001 Location: Colorado Springs, CO Vehicle: 1999 2.5 RS Rally Blue	MY99 Intake (Again) I have been trying to figure out what to do with my intake on my 99 lately and have narrowed it down to several choices. Right now I am running a K&N cone filter with Kartboy MAF adapter and a carbon heat shield. Would I see any gains if I were to switch to a Weapon R tube with my K&N filter or a modified Accruit intake to work with the MAF? Between those two setups which one would be safer for the MAF? Which would be more powerful? Are there any pther things I should consider? BTW I do already have a S-AFC so the high rpm lean issues aren't a big concern. I know there has been MAF intake discusions before, but after searching I didn't find any thing other than DIY intakes. Thanks alot for any help. -Brandon * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
my99 intake box	a&j25rs	Normally Aspirated Powertrain	11	11-08-2002 12:39 AM
MY99 intake	mrbillydee	Normally Aspirated Powertrain	16	05-01-2002 05:07 AM
The ultimate MY99 intake I've seen. (courtesy of Rickard A.)	omahasubaru	Normally Aspirated Powertrain	79	08-31-2001 02:29 AM
MY99 Intake question?	BuRnToAsT420	Normally Aspirated Powertrain	11	06-04-2001 12:31 AM
MY99 Intake Silencer Removed. Couple ?'s	mav1c	Normally Aspirated Powertrain	8	03-13-2001 06:32 PM

11-23-2001, 12:02 AM	#2
Silverscooby27 Scooby Specialist Member#: 9124 Join Date: Aug 2001 Chapter/Region: MAIC Location: Dayton, OH Vehicle: 2013 Mustang GT/CS 2013 Ford Focus ST	Hi, I actually just installed a GanzFlow from Larry Ganz who is out in your neck of the woods. Check out his CAI, he makes one specifically for the MY99 Phase II motor. I haven't installed my S-AFC yet, but am trying to have it done.

11-23-2001, 12:14 PM	#3
DanzBorin Subaru Bounty Hunter Moderator Member#: 7131 Join Date: Jun 2001 Chapter/Region: TXIC Location: Houston - Back in the Alief Vehicle: 2008 STi DGM (3rd STI) prev 05 STi (white)	Check out this! http://www.i-club.com/forums/showthr...threadid=93646 It's the only way to go! Rob