Rescaling Load with "The Spreadsheet" :)

joe-6STi · 11-28-2007, 10:38 PM

After doing so - how might one get the new values back into the Enginuity table after copying the table into the Excel sheet and scaling it ? Is there a way to copy and paste the table back in? I have tried several things to no avail, so for now I'm transfering the values cell by cell, but the chance of error seems kinda high...

Anyone have suggestions ? And yep I searched. And it looks like enginuity is still down too. Rats.

* Registered users of the site do not see these ads.

jays05 · 11-28-2007, 10:47 PM

It works with ecuflash...

Airboy · 11-28-2007, 10:52 PM

In Excel, select the entire table, including the [table3D] in the top left corner, Copy (Ctrl-C) and then go the Enginuity, open the desired table, select "paste" from the "edit" menu.

joe-6STi · 11-28-2007, 10:56 PM

Quote:

Originally Posted by Airboy

In Excel, select the entire table, including the [table3D] in the top left corner, Copy (Ctrl-C) and then go the Enginuity, open the desired table, select "paste" from the "edit" menu.

that exactly what i tried first

Pretty intuitive I know, but...alas no dice.
I have tried putting it in another sheet first, removing the colors, etc...still no paste. Could it be a problem the copy of Enginuity I have ?

joe-6STi · 11-28-2007, 11:02 PM

/thread. I'm a dunce. works now.

DJIMPREZA · 12-01-2007, 09:55 PM

I can type in any decimal value to any cell in the maf scaling table of enginuity running a 07 sti image.. any idea???

Also the up and down arrows do not show any change on the selected cell

I can`t type in calculated maf volt values

Thanks

gabedude · 12-01-2007, 11:23 PM

Quote:

Originally Posted by DJIMPREZA

I can type in any decimal value to any cell in the maf scaling table of enginuity running a 07 sti image.. any idea???

Also the up and down arrows do not show any change on the selected cell

I can`t type in calculated maf volt values

Thanks

Check your user level.

joe-6STi · 12-01-2007, 11:31 PM

Quote:

Originally Posted by gabedude

Check your user level.

Hey Gabe !

I took mine to the drag strip for the first time Last night - saw a bunch of cool things run and raced The Head's Forester. I got owned big time

Running 14.3 with a 60' that was longer than it took the Earth to cool, I think I'l stick to autocross. I was just too scared of abusing the clutch and tranny to try and launch right, But I had fun.

Watching a Forester XT romp on a camaro = priceless.

DJIMPREZA · 12-02-2007, 07:49 PM

Quote:

Originally Posted by gabedude

Check your user level.

Gabe, it was just the Regional configuration from my desktop, I hcanged from Venzuela to US and everything works now

Put a note into the faqs page

thanks

DJ

11-28-2007, 10:38 PM	#1
joe-6STi Scooby Specialist Member#: 141590 Join Date: Feb 2007 Chapter/Region: TXIC Location: Clear Lake, Texas Vehicle: 2010 Silverado 2007 CRF250R	Rescaling Load with "The Spreadsheet" :) After doing so - how might one get the new values back into the Enginuity table after copying the table into the Excel sheet and scaling it ? Is there a way to copy and paste the table back in? I have tried several things to no avail, so for now I'm transfering the values cell by cell, but the chance of error seems kinda high... Anyone have suggestions ? And yep I searched. And it looks like enginuity is still down too. Rats. * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Access tuner race.. rescale load cells?	tolnep	AccessPort	33	02-24-2010 04:14 PM
Rescaling load values?	Brock31	Open Source Reflashes	43	12-09-2008 03:02 PM
just drove over 7000 miles with a wrx loaded with 800lbs of stuff struts out?	prometheum	Brakes, Steering & Suspension	1	11-10-2007 10:32 AM
I had an interview with "the man" today	Jonn	Off-Topic	12	03-11-2004 09:34 AM
350 Z DVD "The RUN" :)	WRXImprezYa	Off-Topic	22	02-22-2003 06:47 PM

11-28-2007, 10:47 PM	#2
jays05 Scooby Specialist Member#: 78165 Join Date: Dec 2004 Chapter/Region: South East Location: SC Vehicle: 05 STI 35r + e85	It works with ecuflash...

11-28-2007, 10:52 PM	#3
Airboy Scooby Specialist Member#: 72829 Join Date: Oct 2004 Chapter/Region: W. Canada Location: Calgary, Canada Vehicle: 2006 HTA68'd wagon Powered by RomRaider	In Excel, select the entire table, including the [table3D] in the top left corner, Copy (Ctrl-C) and then go the Enginuity, open the desired table, select "paste" from the "edit" menu.

11-28-2007, 11:02 PM	#5
joe-6STi Scooby Specialist Member#: 141590 Join Date: Feb 2007 Chapter/Region: TXIC Location: Clear Lake, Texas Vehicle: 2010 Silverado 2007 CRF250R	/thread. I'm a dunce. works now.

12-01-2007, 09:55 PM	#6
DJIMPREZA Scooby Specialist Member#: 1199 Join Date: Apr 2000 Location: Caracas, Venezuela Vehicle: 1994 Supra+1K, 22b alike, 07STI	I can type in any decimal value to any cell in the maf scaling table of enginuity running a 07 sti image.. any idea??? Also the up and down arrows do not show any change on the selected cell I can`t type in calculated maf volt values Thanks