Check your bolt collections - I need a few (intake manifold)

CTKAG · 03-25-2008, 08:16 PM

On a WRX, and I presume most other turbo models with TGV's, there are essentially twelve bolts that hold the intake/TGV's on. They are all 8mm gold anodized, four of them are about 40mm long. I need those four.

Anyone?

TIA

-Keith-

* Registered users of the site do not see these ads.

scoobyless · 03-25-2008, 08:36 PM

Are you talking about the 4 bolts holding the TGV's to the Intake manifold?

Trevor723 · 03-25-2008, 09:38 PM

There are (8) large ones that hold the manifold to the heads and pass thru the tgvs that are all the same.

The red circles:

CTKAG · 03-26-2008, 08:46 AM

Correct - there are 8 long bolts and 4 short bolts - I need the 4 short ones(40mm long). I'm putting a JDM V8 manifold on which only uses the red circled holes on the heads to attach - the long bolts won't work - I need 4 more short ones.

-Keith-

03-25-2008, 08:16 PM	#1
CTKAG Scooby Specialist Member Sales Rating: (21) Member#: 15001 Join Date: Feb 2002 Chapter/Region: NESIC Location: Manchester CT or at any track Vehicle: STi V8 Spec C Power NESIC TrackH0z # 10	Check your bolt collections - I need a few (intake manifold) On a WRX, and I presume most other turbo models with TGV's, there are essentially twelve bolts that hold the intake/TGV's on. They are all 8mm gold anodized, four of them are about 40mm long. I need those four. Anyone? TIA -Keith- * Registered users of the site do not see these ads.

03-25-2008, 09:38 PM	#3
Trevor723 Scooby Specialist Member Sales Rating: (58) Member#: 57989 Join Date: Mar 2004 Chapter/Region: NESIC Location: Maine Vehicle: 2011 F150 EcoBoost flame blue	There are (8) large ones that hold the manifold to the heads and pass thru the tgvs that are all the same. The red circles: Last edited by Trevor723; 03-25-2008 at 10:06 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Subaru GC Parts (EJ25 Engine, Wiring, Injectors, Intake Manifold)	Gomer_GSX	NWIC Private Classifieds	3	02-02-2010 05:51 PM
Check your bolt collections - I need a few (intake manifold)	CTKAG	Private 'Wanted' Classifieds	1	03-27-2008 11:07 AM
FS OH: EJ253 longblock (shortblock, SOHCs, intake manifold)	AWDrivin	Engine/Power/Exhaust	5	09-05-2006 01:37 PM
Anyone have this part (wire harness from intake manifold) 02 wrx	Keith	New England Impreza Club Forum -- NESIC	5	09-24-2005 06:05 PM
Is this right? (on intake manifold)	Meat-Head-h	Factory 2.0L Turbo Powertrain	5	05-29-2004 01:07 PM

03-25-2008, 08:36 PM	#2
scoobyless Scooby Newbie Member Sales Rating: (2) Member#: 40192 Join Date: Jul 2003 Chapter/Region: NESIC Location: New Milford, CT Vehicle: 04 STi Blue/Gold	Are you talking about the 4 bolts holding the TGV's to the Intake manifold?

03-26-2008, 08:46 AM	#4
CTKAG Scooby Specialist Member Sales Rating: (21) Member#: 15001 Join Date: Feb 2002 Chapter/Region: NESIC Location: Manchester CT or at any track Vehicle: STi V8 Spec C Power NESIC TrackH0z # 10	Correct - there are 8 long bolts and 4 short bolts - I need the 4 short ones(40mm long). I'm putting a JDM V8 manifold on which only uses the red circled holes on the heads to attach - the long bolts won't work - I need 4 more short ones. -Keith-