GrimmSpeed TGV Deletes! (We Have Cores Instock = No Downtime!)

GrimmSpeed · 01-30-2008, 12:31 AM

Dont feel like spending $500 for a new set up butterfly-less tgvs or $600 for a JDM Intake Manifold? For less than 1/2 the price you can get the same exact benefits from our TGV Deletes. In this process we take a stock TGV and completely gut it, which includes taking out the metal plate, butterflies, and bar.

These will allow for maximum flow through the TGV. Minimize the engine's heat from entering the TGV's with our ceramic coating. It is very important that heat stays out of the TGV's because this is the last transfer before the intake air enters the engine. Cooler intake air equals more hp.

Customers have seen gains of 15+ whp/wtq. We've also seen third party flowbench tests showing an increase from 330 cfm to 480 cfm!

As far as where the gains occur in the power band, your entire power band is going to see an improvement with our TGV Deletes. On a typical STG 2 setup you are going to realize an increase of 5-10tq/5-8hp in the low end, 10-15tq/8-12hp in the mid range, and 5-10tq/5-8hp at the high end. As you can see in the dyno graph, max gains are going to occur in the mid range.
These will also give you a quicker turbo spool up. If those gains weren't good enough for you, wait till you add a bigger turbo...the bigger the turbo you put on the bigger the gains are going to be from getting the GrimmSpeed TGV Delete.

Yummy!

Thermal Coating!!

Intake Manfiold Side

Head Side

Dyno Graph

This dyno graph was provided to us by one of our customers.

Top Side by Side

Pricing
TGV Delete Service WRX & STi $179.99
Ceramic Thermal Coating $34.99
100% Refundable Core Fee $140

Click below for WRX TGV Delete
http://www.grimmspeed.com/catalog/pr...products_id=35

Click below for STi TGV Delete
http://www.grimmspeed.com/catalog/pr...products_id=44

Any questions please contact us via email, phone, or AIM!

Josh
www.grimmspeed.com
sales@grimmspeed.com
AIM: GrimmSpd
phone:612-481-5731

* Registered users of the site do not see these ads.

SpeedMasterLee · 02-04-2008, 06:39 PM

do you guys weld up the holes where the valves used to be?

GrimmSpeed · 02-05-2008, 03:07 AM

Quote:

Originally Posted by SpeedMasterLee

do you guys weld up the holes where the valves used to be?

basically we tap the holes to create a thread, then put a set screw in it with thread locker. We've probably done 200-300 tgv deletes this way with no issues yet. a few times we used jb weld at the beginning and a couple customers had an issue with that, but we stopped that a long time ago.

Justin

9vapors · 02-07-2008, 11:18 AM

Can you guys pm me the price to have my:
Perrin EL headers/Uppipe/DP
GT35r
Intake Manifold
JDM TGVs ...Ceramic Coated in Black?
Need the TGVs ported too...

Also, I have an extra working set of TGVs, do you guys need more of them?

HOLLYW00D · 02-12-2008, 11:44 PM

hey Justin,

i see the gaskets on your site for tgv to head, but no tgv to intake manifold. do you happen to know the part number for 04 fxt/sti gasket that i will need? (mailbox full).

thanks.
v.

GrimmSpeed · 02-13-2008, 12:42 PM

Quote:

Originally Posted by 9vapors

Can you guys pm me the price to have my:
Perrin EL headers/Uppipe/DP
GT35r
Intake Manifold
JDM TGVs ...Ceramic Coated in Black?
Need the TGVs ported too...

Also, I have an extra working set of TGVs, do you guys need more of them?

pm sent

Josh

Hank3 · 03-07-2008, 09:34 AM

Sent y'all an email

GrimmSpeed · 03-10-2008, 04:10 PM

Quote:

Originally Posted by Hank3

Sent y'all an email

hit you back!

BILLY K · 03-16-2008, 09:05 PM

Grimmspeed did my tgv, my sti intake ported and coated them and they came out awsome, and the ewg uppipe fit great with my fpgreen and my perrin header. these guys do great work. thanks guys BILLY

Wrx_Fan_0717 · 03-22-2008, 12:26 PM

Is it me or are you unable to buy the TGV deletes. Saying the product isn't found?

GrimmSpeed · 03-22-2008, 12:37 PM

Quote:

Originally Posted by Wrx_Fan_0717

Is it me or are you unable to buy the TGV deletes. Saying the product isn't found?

Its not just you. Our main PnP Director/Porter left us yesterday with zero notice. I'm personally in the middle of trying to get this organized and pending orders out. I put a hold on all new orders until we can get caught up, then at that point i'll open the flood gates again.

Justin

Wrx_Fan_0717 · 03-22-2008, 01:00 PM

Quote:

Originally Posted by GrimmSpeed

Its not just you. Our main PnP Director/Porter left us yesterday with zero notice. I'm personally in the middle of trying to get this organized and pending orders out. I put a hold on all new orders until we can get caught up, then at that point i'll open the flood gates again.

Justin

Damn right when i finally get around to getting them.

Bump for you guys.

Bad Noodle · 03-28-2008, 11:33 PM

How come you guys pulled these from you site?

thrasher · 03-30-2008, 07:55 AM

Quote:

Originally Posted by Bad Noodle

How come you guys pulled these from you site?

See post #11 above.

AlxSti · 04-01-2008, 03:01 PM

looks great! i cant wait till i can afford the ewg setup & the tgv deletes!!

Wrx_Fan_0717 · 04-03-2008, 08:27 PM

Bump for you needing a porter and me getting rid of my TGVs.

broben05 · 04-14-2008, 10:25 PM

Could I get a est for wrx intake manifold, tgvs, exhaust manifold / cross pipe. All ceramic coated and pnp. I guess it would be when you guys find a new pnp person.

GrimmSpeed · 04-15-2008, 12:06 AM

Quote:

Originally Posted by AlxSti

looks great! i cant wait till i can afford the ewg setup & the tgv deletes!!

for sure, let us know when you are ready and we can help you out.

Quote:

Originally Posted by Wrx_Fan_0717

Bump for you needing a porter and me getting rid of my TGVs.

we didnt lose all of our guys, we've just had sooo many orders lately that we needed to get caught up. we should be ready to open up the flood gates again in about a week.

GrimmSpeed · 04-17-2008, 11:29 PM

GrimmSpeed Taking new Porting/Coating/Delete Orders Again!

Thats right... After a 3 week hiatus we are now taking new Porting, Ceramic Coating, and TGV Delete orders. Due to high demand for the our porting and coating products we had to stop taking in any new orders but we have now got ourselves caught back up and we are ready to start taking new orders.

All porting and coating products can be found here:
http://www.grimmspeed.com/catalog/in...3e4fq420p5cub2

TGV Deletes can be found here:
http://www.grimmspeed.com/catalog/index.php?cPath=24

We thank each and everyone of you for your patience over the last few weeks while you had to wait to place your orders.

Thanks!

Justin
www.grimmspeed.com
AIM: GrimmSpeed
sales@grimmspeed.com

GrimmSpeed · 04-17-2008, 11:56 PM

GrimmSpeed · 04-18-2008, 04:02 AM

Quote:

Originally Posted by broben05

Could I get a est for wrx intake manifold, tgvs, exhaust manifold / cross pipe. All ceramic coated and pnp.

sending you pm....

Justin
www.grimmspeed.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS: PA grimmspeed tgv deletes	EdsWRX	Engine/Power/Exhaust	4	11-20-2008 02:18 PM
grimmspeed tgv deletes	masemac	NWIC Private Classifieds	5	11-18-2008 08:03 PM
FS in DE: Brand New GrimmSpeed TGV Deletes & Gimmick Turbo Inlet/Maf hose combo	03YellowWRX	Engine/Power/Exhaust	5	07-10-2008 04:00 PM
GrimmSpeed TGV Delete	GrimmSpeed	Engine/Power/Exhaust	52	05-09-2007 12:09 AM

01-30-2008, 12:31 AM	#1
GrimmSpeed NASIOC Vendor Vendor Sales Rating: (192) Member#: 136396 Join Date: Jan 2007 Chapter/Region: MWSOC Location: Minneapolis, MN Vehicle: 2012 wrx white	GrimmSpeed TGV Deletes! (We Have Cores Instock = No Downtime!) Dont feel like spending $500 for a new set up butterfly-less tgvs or $600 for a JDM Intake Manifold? For less than 1/2 the price you can get the same exact benefits from our TGV Deletes. In this process we take a stock TGV and completely gut it, which includes taking out the metal plate, butterflies, and bar. These will allow for maximum flow through the TGV. Minimize the engine's heat from entering the TGV's with our ceramic coating. It is very important that heat stays out of the TGV's because this is the last transfer before the intake air enters the engine. Cooler intake air equals more hp. Customers have seen gains of 15+ whp/wtq. We've also seen third party flowbench tests showing an increase from 330 cfm to 480 cfm! As far as where the gains occur in the power band, your entire power band is going to see an improvement with our TGV Deletes. On a typical STG 2 setup you are going to realize an increase of 5-10tq/5-8hp in the low end, 10-15tq/8-12hp in the mid range, and 5-10tq/5-8hp at the high end. As you can see in the dyno graph, max gains are going to occur in the mid range. These will also give you a quicker turbo spool up. If those gains weren't good enough for you, wait till you add a bigger turbo...the bigger the turbo you put on the bigger the gains are going to be from getting the GrimmSpeed TGV Delete. Yummy! Thermal Coating!! Intake Manfiold Side Head Side Dyno Graph This dyno graph was provided to us by one of our customers. Top Side by Side Pricing TGV Delete Service WRX & STi $179.99 Ceramic Thermal Coating $34.99 100% Refundable Core Fee $140 Click below for WRX TGV Delete http://www.grimmspeed.com/catalog/pr...products_id=35 Click below for STi TGV Delete http://www.grimmspeed.com/catalog/pr...products_id=44 Any questions please contact us via email, phone, or AIM! Josh www.grimmspeed.com sales@grimmspeed.com AIM: GrimmSpd phone:612-481-5731 * Registered users of the site do not see these ads. Last edited by GrimmSpeed; 01-20-2009 at 10:22 AM.

02-04-2008, 06:39 PM	#2
SpeedMasterLee Scooby Specialist Member Sales Rating: (16) Member#: 78417 Join Date: Dec 2004 Chapter/Region: SCIC Location: Torrance, CA Vehicle: 2005 WRX/STI Stage 2 Aspen White	do you guys weld up the holes where the valves used to be?

02-07-2008, 11:18 AM	#4
9vapors Scooby Guru Member Sales Rating: (37) Member#: 92582 Join Date: Aug 2005 Chapter/Region: Tri-State Location: NY Vehicle: *	Can you guys pm me the price to have my: Perrin EL headers/Uppipe/DP GT35r Intake Manifold JDM TGVs ...Ceramic Coated in Black? Need the TGVs ported too... Also, I have an extra working set of TGVs, do you guys need more of them?

02-12-2008, 11:44 PM	#5
HOLLYW00D Scooby Newbie Member Sales Rating: (9) Member#: 44954 Join Date: Oct 2003 Location: Austin, TX	hey Justin, i see the gaskets on your site for tgv to head, but no tgv to intake manifold. do you happen to know the part number for 04 fxt/sti gasket that i will need? (mailbox full). thanks. v.

03-07-2008, 09:34 AM	#7
Hank3 Scooby Guru Member Sales Rating: (22) Member#: 16157 Join Date: Mar 2002 Chapter/Region: South East Location: Tallahassee, FL Vehicle: '03 Mazda P5 <>< '02 WRX & '08 MS3 SOLD!!!	Sent y'all an email

03-16-2008, 09:05 PM	#9
BILLY K Scooby Newbie Member Sales Rating: (0) Member#: 145693 Join Date: Apr 2007 Chapter/Region: South East Location: wesley chapel fl, Vehicle: 2004 sti, aspen white	Grimmspeed did my tgv, my sti intake ported and coated them and they came out awsome, and the ewg uppipe fit great with my fpgreen and my perrin header. these guys do great work. thanks guys BILLY

03-22-2008, 12:26 PM	#10
Wrx_Fan_0717 Scooby Specialist Member Sales Rating: (54) Member#: 152080 Join Date: Jun 2007 Chapter/Region: South East Location: Pensacola, FL Vehicle: 6266 Precision'd Big Cam'd 2.55l 6spd Bugeye	Is it me or are you unable to buy the TGV deletes. Saying the product isn't found?

03-28-2008, 11:33 PM	#13
Bad Noodle Scooby Specialist Member Sales Rating: (23) Member#: 174442 Join Date: Mar 2008 Chapter/Region: Tri-State Location: NNJ Vehicle: 2007 SuperWagon I don't spell well	How come you guys pulled these from you site?

04-01-2008, 03:01 PM	#15
AlxSti Scooby Guru Member Sales Rating: (19) Member#: 94615 Join Date: Aug 2005 Chapter/Region: MAIC Location: Wilmington, DE Vehicle: \|'06 AW VF39 STi\| \|AgileTuned:341WHP/356TQ\|	looks great! i cant wait till i can afford the ewg setup & the tgv deletes!!

04-03-2008, 08:27 PM	#16
Wrx_Fan_0717 Scooby Specialist Member Sales Rating: (54) Member#: 152080 Join Date: Jun 2007 Chapter/Region: South East Location: Pensacola, FL Vehicle: 6266 Precision'd Big Cam'd 2.55l 6spd Bugeye	Bump for you needing a porter and me getting rid of my TGVs.

04-14-2008, 10:25 PM	#17
broben05 Scooby Newbie Member Sales Rating: (1) Member#: 116547 Join Date: Jun 2006 Chapter/Region: MAIC Location: Pittsburgh, PA Vehicle: 2003 Evo 3 16G WRX WRB	Could I get a est for wrx intake manifold, tgvs, exhaust manifold / cross pipe. All ceramic coated and pnp. I guess it would be when you guys find a new pnp person.

04-17-2008, 11:29 PM	#19
GrimmSpeed NASIOC Vendor Vendor Sales Rating: (192) Member#: 136396 Join Date: Jan 2007 Chapter/Region: MWSOC Location: Minneapolis, MN Vehicle: 2012 wrx white	GrimmSpeed Taking new Porting/Coating/Delete Orders Again! Thats right... After a 3 week hiatus we are now taking new Porting, Ceramic Coating, and TGV Delete orders. Due to high demand for the our porting and coating products we had to stop taking in any new orders but we have now got ourselves caught back up and we are ready to start taking new orders. All porting and coating products can be found here: http://www.grimmspeed.com/catalog/in...3e4fq420p5cub2 TGV Deletes can be found here: http://www.grimmspeed.com/catalog/index.php?cPath=24 We thank each and everyone of you for your patience over the last few weeks while you had to wait to place your orders. Thanks! Justin www.grimmspeed.com AIM: GrimmSpeed sales@grimmspeed.com

04-17-2008, 11:56 PM	#20
GrimmSpeed NASIOC Vendor Vendor Sales Rating: (192) Member#: 136396 Join Date: Jan 2007 Chapter/Region: MWSOC Location: Minneapolis, MN Vehicle: 2012 wrx white