Fs: ATX- Clarke mig welder

gda03subaru · 01-07-2010, 01:26 AM

SOLD!!!, will not ship cuz it weighs 50lbs and i dont want to mess with it. dual purpose, used it three times, still looks and performs like new. Its a dual purpose gas and flux core welder. comes with 1 flux core test spool, almost new 2lb spool of er70s6 wire, i will throw in an almost new regulator, a chipping hammer, wire brush, a hand held face sheild. pics upon request, paid $375 1 month ago, i have a tig machine so i do not use this much, planned on doing a little fabrication but plans have changed and i need the cash

part number is clarke 140en
here is some specs

Clarke 140EN MIG/Fluxcore Wire Feed Welder is easily converted from Fluxcore to Gas welding and will weld up to 1/4" inch steel in a single pass! Easily changes to Mig welding for stainless steel and aluminum. Fan cooled for better performance. Electronic wire speed control and 4 variable heat settings allow you to precisely adjust the welder to your needs. Operates on standard 110 volt electrical supply.

110V Wire Welder

Advanced safety overload protection for transformer
Electronic variable wire feed control
4 power settings for maximum welding heat control
Welds steel, stainless steel, aluminum, or cast iron
Fan cooled for better performance
Welds up to 1/4” in a single pass
Uses Fluxcore, Solid Steel, Stainless Steel, Silicon Bronze, and Aluminum welding wire
Welds with or without gas
Tough metal casing
200 Amp ground clamp
CSA approved
Input: 120V, 60 Hz, 20A, 1 Ph
Ouput: 65A@17.5VDC 20%

welder.jpg

* Registered users of the site do not see these ads.

gda03subaru · 01-08-2010, 04:58 PM

Bumpo's Bump Service

gda03subaru · 01-09-2010, 11:18 PM

bump...

gda03subaru · 01-10-2010, 12:11 PM

bump...

gda03subaru · 01-11-2010, 12:15 AM

sold...

01-07-2010, 01:26 AM	#1
gda03subaru Scooby Specialist Member Sales Rating: (17) Member#: 130184 Join Date: Oct 2006 Chapter/Region: TXIC Location: Austin Vehicle: 97' wrangler green with a hint of mud	Fs: ATX- Clarke mig welder SOLD!!!, will not ship cuz it weighs 50lbs and i dont want to mess with it. dual purpose, used it three times, still looks and performs like new. Its a dual purpose gas and flux core welder. comes with 1 flux core test spool, almost new 2lb spool of er70s6 wire, i will throw in an almost new regulator, a chipping hammer, wire brush, a hand held face sheild. pics upon request, paid $375 1 month ago, i have a tig machine so i do not use this much, planned on doing a little fabrication but plans have changed and i need the cash part number is clarke 140en here is some specs Clarke 140EN MIG/Fluxcore Wire Feed Welder is easily converted from Fluxcore to Gas welding and will weld up to 1/4" inch steel in a single pass! Easily changes to Mig welding for stainless steel and aluminum. Fan cooled for better performance. Electronic wire speed control and 4 variable heat settings allow you to precisely adjust the welder to your needs. Operates on standard 110 volt electrical supply. 110V Wire Welder Advanced safety overload protection for transformer Electronic variable wire feed control 4 power settings for maximum welding heat control Welds steel, stainless steel, aluminum, or cast iron Fan cooled for better performance Welds up to 1/4” in a single pass Uses Fluxcore, Solid Steel, Stainless Steel, Silicon Bronze, and Aluminum welding wire Welds with or without gas Tough metal casing 200 Amp ground clamp CSA approved Input: 120V, 60 Hz, 20A, 1 Ph Ouput: 65A@17.5VDC 20% welder.jpg * Registered users of the site do not see these ads. Last edited by gda03subaru; 01-11-2010 at 12:15 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS: Lincoln Electric 180C Mig Welder	unforgiven2144	NESIC Private Classifieds	9	02-28-2013 02:19 PM
FS: CA: Firepower MIG Welder - 120 Amp 115V	05ForesterXT	Non-Subaru Stuff	2	01-02-2010 04:48 PM
FS: Hobart TIG/MIG/Stick Welder	mdcmotorsports	Non-Subaru Stuff	4	02-21-2008 03:11 PM
FS: Miller MIG welder	suby44	RMIC Private Classifieds	2	06-22-2006 04:08 PM
I bought a MIG welder on Tuesday....	skeletor25rs	Texas Impreza Club Forum -- TXIC	4	11-30-2002 02:15 PM

01-08-2010, 04:58 PM	#2
gda03subaru Scooby Specialist Member Sales Rating: (17) Member#: 130184 Join Date: Oct 2006 Chapter/Region: TXIC Location: Austin Vehicle: 97' wrangler green with a hint of mud	Bumpo's Bump Service

01-09-2010, 11:18 PM	#3
gda03subaru Scooby Specialist Member Sales Rating: (17) Member#: 130184 Join Date: Oct 2006 Chapter/Region: TXIC Location: Austin Vehicle: 97' wrangler green with a hint of mud	bump...

01-10-2010, 12:11 PM	#4
gda03subaru Scooby Specialist Member Sales Rating: (17) Member#: 130184 Join Date: Oct 2006 Chapter/Region: TXIC Location: Austin Vehicle: 97' wrangler green with a hint of mud	bump...

01-11-2010, 12:15 AM	#5
gda03subaru Scooby Specialist Member Sales Rating: (17) Member#: 130184 Join Date: Oct 2006 Chapter/Region: TXIC Location: Austin Vehicle: 97' wrangler green with a hint of mud	sold...