Where do you get your flanges?

sumfoo1 · 05-25-2011, 04:19 PM

Stainless Steel Turbo flanges header flanges etc.

I'm looking for a good place to get flanges that won't warp while welding and will hold up well in the long run.

316 is preferred.

Thank you,
foo1

* Registered users of the site do not see these ads.

kcpaz · 05-25-2011, 05:17 PM

I have some in 304 that are 1/2" thick. What size primary are you using. Mine are cut to have a 1.75" OD tube slide inside the flange.

sumfoo1 · 05-25-2011, 06:52 PM

I haven't really decided yet. I'm still investigating how i'm going to set everything up.

SiFlyBy · 05-26-2011, 08:39 AM

I usually get stuff from Aaron Weir:

http://www.weirtech.ca/

AREA1320 · 05-27-2011, 01:36 PM

we have flanges here.

1/2" thick 316 stainless with 1.75" id port size.

$25 each

JRach · 05-29-2011, 01:36 PM

Check out straight line specialties. They make some really good looking flanges for subarus turbos and all sorts of other applications.

ghettocrxsi · 05-31-2011, 06:50 AM

Aaron weir is where I get all my flanges

05-25-2011, 04:19 PM	#1
sumfoo1 Scooby Specialist Member#: 82146 Join Date: Mar 2005 Chapter/Region: South East Location: Raleigh, NC (Brier Creek) Vehicle: 2005 Legacy GT OBP	Where do you get your flanges? Stainless Steel Turbo flanges header flanges etc. I'm looking for a good place to get flanges that won't warp while welding and will hold up well in the long run. 316 is preferred. Thank you, foo1 * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Attn Janq: Where do you get your carcover?	calworld	STi Forum Archive	5	08-27-2003 11:40 AM
where do you get your modded wrx maintained?	WRXinEffect	Bay Area Impreza Club Forum -- BAIC	1	03-13-2003 01:18 AM
Where do you get your tires mounted?	Ru fan	New England Impreza Club Forum -- NESIC	9	12-09-2001 05:06 PM
('93-'01) Where do you get your model cars?	imprezive	Impreza Forum	20	04-10-2001 11:30 PM
So how old is the average Suby owner and where do you get your $$?	myko011	General Forum Archive	208	03-20-2001 12:56 AM

05-25-2011, 05:17 PM	#2
kcpaz Scooby Newbie Member#: 194611 Join Date: Nov 2008 Location: Gilbert Arizona Vehicle: 1998 Legacy GT Mexico Blue (not red)	I have some in 304 that are 1/2" thick. What size primary are you using. Mine are cut to have a 1.75" OD tube slide inside the flange.

05-25-2011, 06:52 PM	#3
sumfoo1 Scooby Specialist Member#: 82146 Join Date: Mar 2005 Chapter/Region: South East Location: Raleigh, NC (Brier Creek) Vehicle: 2005 Legacy GT OBP	I haven't really decided yet. I'm still investigating how i'm going to set everything up.

05-26-2011, 08:39 AM	#4
SiFlyBy Scooby Newbie Member#: 250910 Join Date: Jul 2010 Chapter/Region: MWSOC Location: Bismarck, ND Vehicle: 2002 WRX Blue	I usually get stuff from Aaron Weir: http://www.weirtech.ca/

05-27-2011, 01:36 PM	#5
AREA1320 Former Vendor Member#: 112508 Join Date: Apr 2006 Location: Easton, PA	we have flanges here. 1/2" thick 316 stainless with 1.75" id port size. $25 each

05-29-2011, 01:36 PM	#6
JRach Scooby Specialist Member#: 78075 Join Date: Dec 2004 Chapter/Region: NWIC Location: North Seattle, WA Vehicle: 98' SF5 STI 93' GF8 (rally)	Check out straight line specialties. They make some really good looking flanges for subarus turbos and all sorts of other applications.

05-31-2011, 06:50 AM	#7
ghettocrxsi Scooby Newbie Member#: 277885 Join Date: Mar 2011 Chapter/Region: NWIC Location: portland oregon Vehicle: 2005 sti cgm	Aaron weir is where I get all my flanges