|
||||||||||||||||
 Texas Impreza Club Forum sponsored by Gillman Subaru Houston and Gillman Subaru San Antonio |
|
|
||||||||||||||||
Texas Impreza Club Forum sponsored by Gillman Subaru Houston and Gillman Subaru San Antonio |
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-09-2001, 10:53 AM
|
#1 |
|
Scooby Newbie
Member#: 3353
Join Date: Dec 2000
Location: Austin, Texas
Vehicle:2001 2.5RS Blue Ridge Pearl |
Cobb intake installation
I should have a new Cobb intake in my hand in a few weeks. I don't see it being very hard to install, but any tips would be appreciated.
* Registered users of the site do not see these ads.
|
|
|
|
03-09-2001, 11:03 AM
|
#2 |
|
Scooby Newbie
Member#: 3125
Join Date: Dec 2000
Location: Bedford, DFW
Vehicle:2001 Mustang Bullitt Black |
It looks like the hardest part is taking the old stuff off...
I installed my Ganz intake in about 15 minutes-- that was with 10 minutes messing with the split hose which came off 4 times. The Cobb kit looks teh same. (split hose- the trim which fits around the hole in the fender) btw- anyone in DFW have an old filterbox they want to unload for cheap/free? I want to experiment with some setups. |
|
|
|
|
03-09-2001, 11:16 AM
|
#3 |
|
Scooby Specialist
Member#: 3139
Join Date: Dec 2000
Chapter/Region:
RMIC
Location: SLC Utah
Vehicle:2001 Dodge Pikumup & 08 Triumph Speed Triple |
I was going to say a split hose trim around the hole too.
Josh  |
|
|
|
|
03-09-2001, 11:39 AM
|
#4 |
|
Scooby Specialist
Member#: 3411
Join Date: Jan 2001
Chapter/Region:
TXIC
Location: Plano
Vehicle:2000 '04 VW R32 '05 Yamaha FZ6 |
What'd you cover the old intake hole with JayP?
|
|
|
|
|
03-09-2001, 11:57 AM
|
#5 |
|
Scooby Newbie
Member#: 3125
Join Date: Dec 2000
Location: Bedford, DFW
Vehicle:2001 Mustang Bullitt Black |
Nothing yet--- duct tape?
I'm not going for any show-shines this week. Josh-- I ziptied the split hose into place. I'll get a pic. |
|
|
|
|
03-09-2001, 01:17 PM
|
#6 |
|
Scooby Newbie
Member#: 4363
Join Date: Feb 2001
Location: Austin, Tx
Vehicle:01 impreza rs siverthorn metallic |
i hate connecting the hose but everything else was easy.
|
|
|
|
|
03-09-2001, 01:18 PM
|
#7 |
|
Scooby Newbie
Member#: 3353
Join Date: Dec 2000
Location: Austin, Texas
Vehicle:2001 2.5RS Blue Ridge Pearl |
old intake hole?
OK I'll take the risk of sounding dumb..(newbie, afterall) If the intake connects to the engine and then routes through the fender well, where's the extra hole? |
|
|
|
|
03-09-2001, 04:45 PM
|
#8 |
|
Scooby Specialist
Member#: 3805
Join Date: Jan 2001
Chapter/Region:
International
Location: Paris, FR / Houston, TX
Vehicle:2011 STi Sedan SWP 2011 Outback ABP |
There are two large holes, one smaller than the other, plus various other dime sized or smaller ones. Your intake will go into the largest one. Ganz recommends plugging the second large hole, towards the rear of the intake one. The small ones are insignificant.
Xio |
|
|
|
|
03-09-2001, 07:45 PM
|
#9 |
|
Scooby Newbie
Member#: 3125
Join Date: Dec 2000
Location: Bedford, DFW
Vehicle:2001 Mustang Bullitt Black |
I've added some pics of my Ganz install with the zip ties and all!
On my site--- http://home.earthlink.net/~palmerj/ |
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Cobb Intake Install...need help quick | Jard | Normally Aspirated Powertrain | 10 | 07-02-2003 04:55 PM |
| Cobb intake install how to? | nick robinson | Normally Aspirated Powertrain | 24 | 05-31-2003 05:27 AM |
| COBB Intake installed + nifty extra antibounce pipe. | 2.5RSMatt | Member's Car Gallery | 2 | 04-24-2003 08:49 PM |
| Cobb Intake installation in 97 GT update | 2.5GT | Legacy Forum | 0 | 02-14-2002 11:28 AM |
| Cobb Intake Installed! | urapnis | Normally Aspirated Powertrain | 3 | 07-06-2001 03:03 PM |
All times are GMT -4. The time now is 11:00 AM.
Linear Mode
