Putting together the T3/T04B

WRX 555 STi · 05-28-2003, 07:06 PM

Does anyone know how to put the T3/T04B back together? I have it all apart in screws and parts.
I am looking for instructions.
~Anthony.

* Registered users of the site do not see these ads.

8Complex · 05-29-2003, 02:22 AM

Like... the internals and all??

I had a web site that said how to rebuild one, but I lost the page address somewhere over the years.

But why in the hell would you take it all apart and not note where everything goes to put it back together??

dyswtric27 · 05-30-2003, 12:17 AM

Not sure if that helps or not.
Link.

WRX 555 STi · 05-30-2003, 05:11 PM

Nick - I took pictures and wrote down stuff when i was taking it apart. I put it back together, but I run into problems once i tighten any screws. The self-locking nut on the compressor wheel locks the turbine shaft and nothing turns. I unscrewed that somewhat, then I tried to tighten the backplate of the compressor to the bearing assembly. It always seems that something is too tight and nothing turns. I guess I will have to send this out to get it repaired until my new one comes in from Tom.

~Anthony.

05-28-2003, 07:06 PM	#1
WRX 555 STi Scooby Specialist Member#: 8042 Join Date: Jul 2001 Location: Elmwood Park, IL Vehicle: MY00 WRS - '04 WRX 2002 Dragon slayer :)	Putting together the T3/T04B Does anyone know how to put the T3/T04B back together? I have it all apart in screws and parts. I am looking for instructions. ~Anthony. * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wanna Help Put Together The Next Drive?	Troa	North West Impreza Club Forum -- NWIC	13	09-13-2008 07:35 PM
turbonetics t3/t04b	wrxtremeWGN	Factory 2.0L Turbo Powertrain	6	01-29-2004 05:01 PM
Garrett T3/T04B (from ludespeed) boost range?	agent007kimball	Normally Aspirated with bolt-on Forced Induction Powertrain	5	08-07-2003 03:38 PM
t3 vs t3/t04b	Blindeye_03	Normally Aspirated with bolt-on Forced Induction Powertrain	4	07-13-2001 08:06 PM

05-29-2003, 02:22 AM	#2
8Complex Moderator Member#: 922 Join Date: Feb 2000 Chapter/Region: MWSOC Location: Schaumburg, IL Vehicle: 04 FXT Red	Like... the internals and all?? I had a web site that said how to rebuild one, but I lost the page address somewhere over the years. But why in the hell would you take it all apart and not note where everything goes to put it back together??

05-30-2003, 12:17 AM	#3
dyswtric27 Scooby Newbie Member#: 404 Join Date: Oct 1999 Location: socal Vehicle: 2000 Audi S4 endless.night	Not sure if that helps or not. Link.

05-30-2003, 05:11 PM	#4
WRX 555 STi Scooby Specialist Member#: 8042 Join Date: Jul 2001 Location: Elmwood Park, IL Vehicle: MY00 WRS - '04 WRX 2002 Dragon slayer :)	Nick - I took pictures and wrote down stuff when i was taking it apart. I put it back together, but I run into problems once i tighten any screws. The self-locking nut on the compressor wheel locks the turbine shaft and nothing turns. I unscrewed that somewhat, then I tried to tighten the backplate of the compressor to the bearing assembly. It always seems that something is too tight and nothing turns. I guess I will have to send this out to get it repaired until my new one comes in from Tom. ~Anthony.