WRC Crank Pulley

imprezaboi · 08-14-2003, 06:09 AM

I recently came across a WRC Crank pulley made by Zerosports but I am unsure as to whether it is smaller then the stock pulley.
Does anyone know if its smaller or not?

Thanks

* Registered users of the site do not see these ads.

imprezaboi · 08-15-2003, 09:13 AM

bump

Compressed · 08-15-2003, 11:58 AM

hmm I don't have any experience with that part, but I bet if you presented some data, such as a measurement of the diameter then we could tell you if it was underdriven or not. In fact I'll go measure my stock crank pulley for you to compare to the Zerosports piece if you get a measurement of that part.

imprezaboi · 08-15-2003, 01:14 PM

Thanks that would be just great dia is 5 1/4 inches
2 inches in total thickness
1 1/2 inches thick where the pulley belts run

Thanks
Benson

HndaTch627 · 08-15-2003, 01:18 PM

last i recall the Prodrive Crank pullies were stock in diameter they were just lighter weight.

jeremy

Reset · 08-16-2003, 01:03 AM

you should have ask me, I have WRC Crank pulley.

yup, they are the same in diameter just the weight different.

WRBlue Flava · 08-04-2004, 01:16 AM

any problems with the zerosports crank pulley?
how many miles have u travelled on it?
thinking of gettin one

QKWRX · 08-04-2004, 01:41 AM

Not to get slightly off topic but I have a Perrin crank pulley and haven't had any problems.

I'd say go for it! Perrin pulley is 1.2lbs if you want to do a quick comparison between Perrin and WRC.

Reset · 08-04-2004, 02:09 PM

Quote:

Originally Posted by WRBlue Flava

any problems with the zerosports crank pulley?
how many miles have u travelled on it?
thinking of gettin one

no problem at all
it had been running for 2year now

08-14-2003, 06:09 AM	#1
imprezaboi Scooby Specialist Member#: 7382 Join Date: Jun 2001 Chapter/Region: VIC Location: Vancouver, BC Vehicle: MY01 GC8 - 4 BRP	WRC Crank Pulley I recently came across a WRC Crank pulley made by Zerosports but I am unsure as to whether it is smaller then the stock pulley. Does anyone know if its smaller or not? Thanks * Registered users of the site do not see these ads. Last edited by imprezaboi; 08-14-2003 at 09:39 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Crank Pulley Stuck- NOT Crank Pulley Bolt	SubieNOVA	Factory 2.0L Turbo Powertrain	20	01-23-2008 12:36 PM
WTT Brand new gold cobb crank pulley for polished crank pulley	IllNastyImpreza	NESIC Private Classifieds	2	03-02-2007 05:08 PM
Zerosports WRC crank pulley	Steadydpn1	Factory 2.5L Turbo Powertrain	0	08-31-2006 06:41 PM
I will trade my perrin crank pulley for a stock crank pulley	NITROS	Mid West Subaru Owners Club Forum -- MWSOC	8	07-21-2006 10:51 AM
Perrin Crank Pulley Vs Unorthodox Racing Ultra S lightened underdrive crank pulley	west_minist	Normally Aspirated Powertrain	3	02-21-2005 11:56 PM

08-15-2003, 09:13 AM	#2
imprezaboi Scooby Specialist Member#: 7382 Join Date: Jun 2001 Chapter/Region: VIC Location: Vancouver, BC Vehicle: MY01 GC8 - 4 BRP	bump

08-15-2003, 11:58 AM	#3
Compressed Scooby Newbie Member#: 12271 Join Date: Nov 2001 Location: Colorado Vehicle: 2012 4Runner TE KDSS!	hmm I don't have any experience with that part, but I bet if you presented some data, such as a measurement of the diameter then we could tell you if it was underdriven or not. In fact I'll go measure my stock crank pulley for you to compare to the Zerosports piece if you get a measurement of that part.

08-15-2003, 01:14 PM	#4
imprezaboi Scooby Specialist Member#: 7382 Join Date: Jun 2001 Chapter/Region: VIC Location: Vancouver, BC Vehicle: MY01 GC8 - 4 BRP	Thanks that would be just great dia is 5 1/4 inches 2 inches in total thickness 1 1/2 inches thick where the pulley belts run Thanks Benson

08-15-2003, 01:18 PM	#5
HndaTch627 Scooby Guru Member#: 6551 Join Date: May 2001 Chapter/Region: MWSOC Location: Carol Stream, IL Vehicle: '01 GC8 Dinged STM '09 Concours 14 ABS Black	last i recall the Prodrive Crank pullies were stock in diameter they were just lighter weight. jeremy

08-16-2003, 01:03 AM	#6
Reset Scooby Specialist Member#: 11118 Join Date: Oct 2001 Chapter/Region: VIC Location: Vancouver,BC Canada Vehicle: 2002 2.5 TS Aspen white	you should have ask me, I have WRC Crank pulley. yup, they are the same in diameter just the weight different.

08-04-2004, 01:16 AM	#7
WRBlue Flava Scooby Newbie Member#: 58071 Join Date: Mar 2004 Vehicle: 2004 WRX WR Blue	any problems with the zerosports crank pulley? how many miles have u travelled on it? thinking of gettin one

08-04-2004, 01:41 AM	#8
QKWRX Scooby Specialist Member#: 66711 Join Date: Jul 2004 Chapter/Region: NWIC Location: Richland, Wa Vehicle: 01 BMW 330CIC LMY	Not to get slightly off topic but I have a Perrin crank pulley and haven't had any problems. I'd say go for it! Perrin pulley is 1.2lbs if you want to do a quick comparison between Perrin and WRC.