AVCS hook up problem need help

fatray · 05-02-2004, 07:47 PM

It's been some time now, but better late then never. Finally hooking up my AVCS. I have the JDM wiring harness (I was told) problem is I go to wire engine up with the harness and one plug dosn't fit!

The other side fits fine but there is this same white connector with no were to hook up. Other white connector seems to taped to harness and not ment to be used. Both are male, both don't connect to anything. The wire hook ups for the heads (I assume) colors are blue and yellow for the 2 wires. The one taped up is orange/blue white/blue.

Found places to hook every thing else up except these 2 connectors.

Any insite here? I looked around and just found diagrams on hooking up to the ECU.

* Registered users of the site do not see these ads.

fatray · 05-02-2004, 07:58 PM

I need this wire. Found it on ClubWRX forums. Anyone have this for me? If only I could remember who I bought the harness from.

MK19_ · 05-02-2004, 10:10 PM

Isn't that the camshaft position sensor for the driver side rear?

dwx · 05-02-2004, 11:38 PM

Yeah you need the pigtail connector things, I had the same problem since I got bare heads from someone. If you get a _brand new_ engine harness from a V7 it does not come with those connectors, they must come with the sensor or something...Contact the usual suspect of people that get JDM engines like kingpin, gruppe-s, axis racing, etc. and they may have them.

fatray · 05-03-2004, 12:17 AM

DO I need two of them?

AZScoobie · 05-03-2004, 02:39 AM

Call Kingpin.

C

05-02-2004, 07:47 PM	#1
fatray Scooby Specialist Member#: 18150 Join Date: Apr 2002 Chapter/Region: MAIC Location: Baltimore MD Vehicle: 2002 WRX Wagon EJ207 Velocity Red, Liberal kit	AVCS hook up problem need help It's been some time now, but better late then never. Finally hooking up my AVCS. I have the JDM wiring harness (I was told) problem is I go to wire engine up with the harness and one plug dosn't fit! The other side fits fine but there is this same white connector with no were to hook up. Other white connector seems to taped to harness and not ment to be used. Both are male, both don't connect to anything. The wire hook ups for the heads (I assume) colors are blue and yellow for the 2 wires. The one taped up is orange/blue white/blue. Found places to hook every thing else up except these 2 connectors. Any insite here? I looked around and just found diagrams on hooking up to the ECU. * Registered users of the site do not see these ads.

05-02-2004, 07:58 PM	#2
fatray Scooby Specialist Member#: 18150 Join Date: Apr 2002 Chapter/Region: MAIC Location: Baltimore MD Vehicle: 2002 WRX Wagon EJ207 Velocity Red, Liberal kit	Found my problem I need this wire. Found it on ClubWRX forums. Anyone have this for me? If only I could remember who I bought the harness from.

05-03-2004, 12:17 AM	#5
fatray Scooby Specialist Member#: 18150 Join Date: Apr 2002 Chapter/Region: MAIC Location: Baltimore MD Vehicle: 2002 WRX Wagon EJ207 Velocity Red, Liberal kit	2 DO I need two of them?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
battery got hooked up backwards, need help finding gremlins	5spd Alcyone	Electrical & Lighting	5	02-10-2007 09:35 PM
I got the hook up! Anyone need a detail?	mykrrrr	Mid West Subaru Owners Club Forum -- MWSOC	11	09-20-2006 09:08 PM
hooking up amp/subs help	vincent-h	Car Audio, Video & Security	3	01-17-2006 09:27 PM
Dell Inspiron 8200 boot up problem, please help	Unabomber	Off-Topic	7	10-29-2005 04:55 PM
Autometer a/f ratio gage- best location to hook up power. Need help quick-please.	odin1	Electrical & Lighting	11	12-09-2003 12:17 AM

05-02-2004, 10:10 PM	#3
MK19_ Scooby Specialist Member#: 49148 Join Date: Nov 2003 Chapter/Region: South East Location: Plantation, FL Vehicle: Dogs are forever in the pushup position...	Isn't that the camshaft position sensor for the driver side rear?

05-02-2004, 11:38 PM	#4
dwx Scooby Guru Member#: 8343 Join Date: Jul 2001 Chapter/Region: MWSOC Location: Atlanta, GA Vehicle: 2005 2012 Jeep 2013 DGM BRZ	Yeah you need the pigtail connector things, I had the same problem since I got bare heads from someone. If you get a _brand new_ engine harness from a V7 it does not come with those connectors, they must come with the sensor or something...Contact the usual suspect of people that get JDM engines like kingpin, gruppe-s, axis racing, etc. and they may have them.

05-03-2004, 02:39 AM	#6
AZScoobie Scooby Guru Member#: 8785 Join Date: Jul 2001 Chapter/Region: SWIC Vehicle: 02 c_turner@ix. netcom.com	Call Kingpin. C