2002 WRX EJ205 Short block and long block, plus lots of extra STi and WRX parts

pegdrgr · 05-30-2004, 01:50 PM

I have lots of parts that have been sitting in my garage for several months now. Prices do not include shipping or paypal fees. I only charge actual shipping, and can find ways to ship the heavy items for cheap. Please give me your addy and I will get you a shipping quote. I will ship international, but I will not hold items for extended periods of time waiting unless you pay now.

The pictures are below, I assume you can put the picture with the part

1. 2002 WRX short block. $400 You can see the cross hatching is still perfect. This motor comes with everything that you see in the picture. The motor was running perfectly when we pulled it apart to swap in a 2.5 short block. Motor had 20K miles on it when removed from car.

2. 2002 WRX longblock. $1250 Sold This motor ran perfectly all it's life. It was a stage 4 car when I removed it to install a Spec C motor. In January it dynod 325 whp. I am going with a GT30R setup and wanted a motor that would take more abuse and breath better. I guarantee this motor had no problems when I removed it from my car last month. It has 32K miles on it, stage 4 since 22K. There are some sensors shown in the picture that will not go with it, i.e. my Greddy EGT probe and oil pressure sensor.

3. Clutch and flywheel. $50 This clutch came off the shortblock motor with 20K miles on it. The plates are worn, but have some left if you are looking to just get by for a while until you can afford more.

4. R160 rear end. $200 This came out of my wagon when I swapped in the 6 speed setup. It worked perfectly when I removed it from the car. 26K miles on it. I can remove the cross member if needed to reduce the cost of shipping.

5. STi Spec C AC compressor. $150 This came off my spec C motor and includes the needed bracket to mount it. This weighs 9 lbs less than your stock compressor. If you are looking to save some weight and not lose your AC this is a great way to go. I have no idea how well it works in hotter climates since I never ran it. The motor it came off of had 6K miles.

6. WRX motor and tranny mount. $20. Sold These are off a WRX and are the same part number as the STi mounts, not group N.

7. JDM alternator. $50 Sold

[b]8. JDM power steering pump. $40- Sold.

9. V7 STi front knuckles. $100 Sold

10. V7 STi tranny cross member. $20 Sold

11. WRX front calipers and brackets. $75 Sold

12. WRX Drive line. $30 This came off my wagon when I did the 6 speed swap. It has 26K miles on it. It works perfectly, but may be difficult to ship since it is about 4 feet long. It may be best to ship this with the R160.

13. WRX wagon 1/2 shafts. $100 for all 4.Sold

14. JDM STi starter. $30. Sold
Now for the pictures

Short block

Edit: clarified about sensors shown in the LB pictures.

* Registered users of the site do not see these ads.

pegdrgr · 05-30-2004, 01:50 PM

Longblock

Clutch and flywheel

R160

AC compressor

Motor and tranny mount
sold

Alternator
Sold

Power steering pump
Sold

pegdrgr · 05-30-2004, 01:51 PM

Front knuckles
Sold

Tranny cross member
Sold

Front brake calipers
Sold

Drive line

1/2 shafts
Sold

Starter
Sold

pegdrgr · 05-31-2004, 09:45 AM

bump

BlkTS02 · 05-31-2004, 05:05 PM

Pm'd ya.

pegdrgr · 05-31-2004, 08:36 PM

Replied

Geoff · 06-01-2004, 01:59 PM

Bump. I can vouch for this seller.

Geoff · 06-01-2004, 09:26 PM

Another free bump.

elhalisf · 06-01-2004, 09:30 PM

Interested in the tranny mount. How much for that overnighted to michigan 48201. I would really need that shipped tomorrow, can you do that? I can pay you through paypal if the deal is right tonight.

pegdrgr · 06-02-2004, 03:39 PM

Unfortunately I did not see your post before I went to FedEx today. Do you still want it if I ship it out overnight tomorrow?

Quote:

Originally posted by elhalisf
Interested in the tranny mount. How much for that overnighted to michigan 48201. I would really need that shipped tomorrow, can you do that? I can pay you through paypal if the deal is right tonight.

pegdrgr · 06-02-2004, 10:35 PM

Bump

Weemus · 06-02-2004, 11:41 PM

Ill take the alternator.
P.M.ed you

pegdrgr · 06-03-2004, 12:21 AM

Replied

Quote:

Originally posted by Weemus
Ill take the alternator.
P.M.ed you

subysouth · 06-03-2004, 12:58 AM

I would really like to ask you about 20 questions but lemme just narrow it down to 2 if you have the time.

1. Did you use your stock ecu with the spec c long block?

2. What 2.5 liter did you swap the heads from the short block onto? The 2.5 na short block or the STi block?

Thanks and a bump for ya.

ss

pegdrgr · 06-03-2004, 01:07 AM

1. No, JDM ECU and a UTEC.

2. STi block, as seen in the write up I did in the conversion forum.

pegdrgr · 06-03-2004, 11:19 AM

Bump

kidatari · 06-04-2004, 05:17 AM

A big bump for Pegdrgr. Great seller!

pegdrgr · 06-05-2004, 08:43 PM

Back to the top

scooby · 06-06-2004, 11:15 AM

may be interested in long block will let you know asap

pegdrgr · 06-06-2004, 11:41 AM

Shoot me a PM when you know.

Quote:

Originally posted by scooby
may be interested in long block will let you know asap

pegdrgr · 06-07-2004, 03:18 PM

another day, another bump

pegdrgr · 06-08-2004, 03:41 PM

Bump for more parts sold

pegdrgr · 06-15-2004, 11:02 PM

Back to the top!

pegdrgr · 06-21-2004, 01:02 AM

Motor anyone?

pegdrgr · 06-24-2004, 10:02 PM

Sending it back North.

05-30-2004, 01:50 PM	#1
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	2002 WRX EJ205 Short block and long block, plus lots of extra STi and WRX parts I have lots of parts that have been sitting in my garage for several months now. Prices do not include shipping or paypal fees. I only charge actual shipping, and can find ways to ship the heavy items for cheap. Please give me your addy and I will get you a shipping quote. I will ship international, but I will not hold items for extended periods of time waiting unless you pay now. The pictures are below, I assume you can put the picture with the part 1. 2002 WRX short block. $400 You can see the cross hatching is still perfect. This motor comes with everything that you see in the picture. The motor was running perfectly when we pulled it apart to swap in a 2.5 short block. Motor had 20K miles on it when removed from car. 2. 2002 WRX longblock. $1250 Sold This motor ran perfectly all it's life. It was a stage 4 car when I removed it to install a Spec C motor. In January it dynod 325 whp. I am going with a GT30R setup and wanted a motor that would take more abuse and breath better. I guarantee this motor had no problems when I removed it from my car last month. It has 32K miles on it, stage 4 since 22K. There are some sensors shown in the picture that will not go with it, i.e. my Greddy EGT probe and oil pressure sensor. 3. Clutch and flywheel. $50 This clutch came off the shortblock motor with 20K miles on it. The plates are worn, but have some left if you are looking to just get by for a while until you can afford more. 4. R160 rear end. $200 This came out of my wagon when I swapped in the 6 speed setup. It worked perfectly when I removed it from the car. 26K miles on it. I can remove the cross member if needed to reduce the cost of shipping. 5. STi Spec C AC compressor. $150 This came off my spec C motor and includes the needed bracket to mount it. This weighs 9 lbs less than your stock compressor. If you are looking to save some weight and not lose your AC this is a great way to go. I have no idea how well it works in hotter climates since I never ran it. The motor it came off of had 6K miles. 6. WRX motor and tranny mount. $20. Sold These are off a WRX and are the same part number as the STi mounts, not group N. 7. JDM alternator. $50 Sold [b]8. JDM power steering pump. $40- Sold. 9. V7 STi front knuckles. $100 Sold 10. V7 STi tranny cross member. $20 Sold 11. WRX front calipers and brackets. $75 Sold 12. WRX Drive line. $30 This came off my wagon when I did the 6 speed swap. It has 26K miles on it. It works perfectly, but may be difficult to ship since it is about 4 feet long. It may be best to ship this with the R160. 13. WRX wagon 1/2 shafts. $100 for all 4.Sold 14. JDM STi starter. $30. Sold Now for the pictures Short block Edit: clarified about sensors shown in the LB pictures. * Registered users of the site do not see these ads. Last edited by pegdrgr; 07-03-2004 at 02:24 PM.

05-30-2004, 01:50 PM	#2
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Longblock Clutch and flywheel R160 AC compressor Motor and tranny mount sold Alternator Sold Power steering pump Sold Last edited by pegdrgr; 06-11-2004 at 11:59 PM.

05-30-2004, 01:51 PM	#3
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Front knuckles Sold Tranny cross member Sold Front brake calipers Sold Drive line 1/2 shafts Sold Starter Sold Last edited by pegdrgr; 06-03-2004 at 02:52 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GI: 2002/3 EJ205 short block <20k.	ChrisRT	NWIC Private Classifieds	0	03-08-2009 06:52 AM
huge Turbo XS dp, Kartboy s.s., and Vivid Racing s.s, plus lots of stock parts	Anamagous	NWIC Private Classifieds	13	08-09-2008 01:29 PM
XBOX360 plus lots of extras.	Wheels	Non-Subaru Stuff	12	05-07-2007 10:22 PM
FS: NJ 2002 Wrb Stage 4 WRX w/ lots of extras	RageWoRX	Private Vehicle 'For Sale' Classifieds	15	07-14-2006 12:05 PM
Lots of pics...STi and other cars (skyline, supra, etc)	337	Member's Car Gallery	26	05-11-2005 12:47 AM

05-31-2004, 09:45 AM	#4
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	bump

05-31-2004, 05:05 PM	#5
BlkTS02 Scooby Specialist Member Sales Rating: (14) Member#: 50142 Join Date: Dec 2003 Chapter/Region: South East Location: West TN Vehicle: 2002 2.5TS MBP	Pm'd ya.

05-31-2004, 08:36 PM	#6
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Replied

06-01-2004, 01:59 PM	#7
Geoff Warden of NASIOC Timeout Super Moderator Member Sales Rating: (18) Member#: 592 Join Date: Dec 1999 Chapter/Region: TXIC Location: P-Ville, Texas Vehicle: '08 X3 3.0si 6MT '03 330xi 6MT & '08 STi	Bump. I can vouch for this seller.

06-01-2004, 09:26 PM	#8
Geoff Warden of NASIOC Timeout Super Moderator Member Sales Rating: (18) Member#: 592 Join Date: Dec 1999 Chapter/Region: TXIC Location: P-Ville, Texas Vehicle: '08 X3 3.0si 6MT '03 330xi 6MT & '08 STi	Another free bump.

06-01-2004, 09:30 PM	#9
elhalisf Scooby Specialist Member Sales Rating: (9) Member#: 56332 Join Date: Mar 2004 Chapter/Region: MWSOC Location: Clinton Twp, MI Vehicle: 2005 STI Cobb Stg 2	Interested in the tranny mount. How much for that overnighted to michigan 48201. I would really need that shipped tomorrow, can you do that? I can pay you through paypal if the deal is right tonight.

06-02-2004, 10:35 PM	#11
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Bump

06-02-2004, 11:41 PM	#12
Weemus Scooby Specialist Member Sales Rating: (4) Member#: 16415 Join Date: Mar 2002 Chapter/Region: BAIC Location: East Bay in the CA Vehicle: 02 WRX WRBwhatothercoloristhere?	Ill take the alternator. P.M.ed you

06-03-2004, 12:58 AM	#14
subysouth Scooby Guru Member Sales Rating: (9) Member#: 5039 Join Date: Mar 2001 Chapter/Region: South East Location: Ocean Springs, MS Vehicle: 2007 Outback XT Grey 5-speed	I would really like to ask you about 20 questions but lemme just narrow it down to 2 if you have the time. 1. Did you use your stock ecu with the spec c long block? 2. What 2.5 liter did you swap the heads from the short block onto? The 2.5 na short block or the STi block? Thanks and a bump for ya. ss

06-03-2004, 01:07 AM	#15
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	1. No, JDM ECU and a UTEC. 2. STi block, as seen in the write up I did in the conversion forum.

06-03-2004, 11:19 AM	#16
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Bump

06-04-2004, 05:17 AM	#17
kidatari Scooby Specialist Member Sales Rating: (0) Member#: 10441 Join Date: Sep 2001 Chapter/Region: BAIC Location: Northern California	A big bump for Pegdrgr. Great seller!

06-05-2004, 08:43 PM	#18
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Back to the top

06-06-2004, 11:15 AM	#19
scooby Scooby Specialist Member Sales Rating: (8) Member#: 13085 Join Date: Dec 2001 Location: Under a Rock	may be interested in long block will let you know asap

06-07-2004, 03:18 PM	#21
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	another day, another bump

06-08-2004, 03:41 PM	#22
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Bump for more parts sold

06-15-2004, 11:02 PM	#23
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Back to the top!

06-21-2004, 01:02 AM	#24
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Motor anyone?

06-24-2004, 10:02 PM	#25
pegdrgr Scooby Specialist Member Sales Rating: (2) Member#: 25693 Join Date: Oct 2002 Location: Portland, Or Vehicle: 2008 18x9" goodness E85-380ftlbs @ 3100	Sending it back North.