|
|
|
|
Thread Tools | Display Modes |
11-04-2000, 05:40 PM | #1 |
Scooby Specialist
Member#: 524
Join Date: Nov 1999
Location: WA
Vehicle:04 STi White |
22B vents on 88 GL-10
Well here are two pics of the 22B replicas I got from Teagues.
Any thoughts that would make them sit better? What about the gap on the outside edge that I can't seem to get rid of? http://web.nmsu.edu/~ewitte/Yellowhood_1.JPG http://web.nmsu.edu/~ewitte/yellowhood_2.JPG Yes I realise my car is Tacky/ricey as hell but its cheaper to slap yellow spray paint on it than to repaint it with real paint, or have the hood rust off.
* Registered users of the site do not see these ads.
|
11-04-2000, 06:23 PM | #2 |
Scooby Guru
Member#: 1904
Join Date: Jul 2000
Chapter/Region:
TXIC
Location: Austin, TX
Vehicle:2017 Impreza Sport E36 M3/4/5 |
do you have headlights? and, no i don't know the answer to your question
but i do like it! [This message has been edited by JGard18 (edited November 04, 2000).] |
11-04-2000, 06:28 PM | #3 |
Friendly Neighbourhood
Moderator Member#: 269
Join Date: Sep 1999
Chapter/Region:
VIC
Location: Burnaby, B.C., Canada
Vehicle:2005 ABP LGT LTD BP6 00 Impreza RS GM6 RIP |
Old school - new school Subaru! Kewl!
LaterZ! Darren!! |
11-04-2000, 06:29 PM | #4 |
Scooby Specialist
Member#: 524
Join Date: Nov 1999
Location: WA
Vehicle:04 STi White |
They are in the garage somewhere, with the bumper and turn signals.
They are off while I monkey with the motor and other stuff. It takes maybe 30 minutes to put the whole front end back on now that I have had a little practice. |
11-04-2000, 07:41 PM | #5 |
Scooby Specialist
Member#: 1110
Join Date: Mar 2000
Location: USA
Vehicle:1999 RS Silver |
The problem is that a 22B has a recessed lip where the vent attaches. I'd imagine a competent body shop guy could recess the lip on your hood and make them fit flush.
|
11-05-2000, 11:13 AM | #6 |
Scooby Guru
Member#: 1426
Join Date: May 2000
Chapter/Region:
NESIC
Location: New Boston, NH
Vehicle:'07 335xi,14 Tundra 848 Evo Race Bike |
Any major auto parts catalog will sell tools to recess a panel. I don't remember what they're called but they look similiar to a set of vice grips with different lips welded on. Just by squeezing the vice grip on the metal it recesses it to a certain height, depending on what lip height you have in the vice grip. I think that would be your best bet...
Fitz |
11-06-2000, 05:56 PM | #7 |
Guest
Member#:
|
either that or BONDO the hella out of it...or maybe a thick gasket seal or something of that sort...???
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
88 gl-10 engine swap | chevelle8389 | 'Old School' Subaru Forum | 5 | 11-23-2006 11:37 PM |
Advice on 88 GL wagon, non turbo | subeesteve25 | 'Old School' Subaru Forum | 4 | 11-04-2005 08:04 PM |
04 STI scoop + 22B vents on a 98RS hood | donut | Interior & Exterior Modification | 9 | 04-23-2004 06:12 PM |
new problem with 88 gl 10 | jjtdiceman | 'Old School' Subaru Forum | 0 | 02-22-2004 08:38 PM |
22b vents on a MY02 WRX | quentinberg007 | Interior & Exterior Modification | 14 | 11-30-2001 10:10 AM |