BE Brullen 2.5" Catback FS

PHATsuby · 09-28-2005, 06:59 PM

Hey fellow BE'ers,

figured I would post here since It is so model specific, I am selling my turbo kit off as you know and I am also selling off my nice Brullen exhaust. It is 2.5" piping, with single 80mm tip, quiet acoustics(larger resonator). It sounds awesome, just putting on the one I made so this is coming off and will be available this weekend.

These are full SS mandrel bend exhausts, bolts up to stock cat section.

I will take pics when I get back this weekend.

looking for 400 shipped(in the lower 48).

if you have any questions let me know

thanks

Ben

* Registered users of the site do not see these ads.

IDMO · 09-28-2005, 07:01 PM

would 2.5" piping have any ill effects on an n/a BE?

i'd like to see pics when you get 'em

PHATsuby · 09-28-2005, 10:20 PM

2.5" piping is on the larger side for NA applications, you would see more gains in the higher rpm ranges, but you may lose a bit of low end torque, I really dont know how siginificant it would actually be especially if you still had your stock cats creating the majority of the back pressure.

I will get pics up this weekend.

thanks

Ben

MitchGT · 09-29-2005, 12:56 AM

Any buyers for your turbo setup yet Ben?

PHATsuby · 09-29-2005, 05:11 AM

Hey Mitch,
someone has bought my Autronic, the mechanicals are still available though.

Ben

MitchGT · 09-29-2005, 01:02 PM

Any chance of a sound clip Ben?

PHATsuby · 10-22-2005, 05:19 PM

well, finally got a chance to take some pics. so here they are.

here is the only rear flaw that would possibly matter, scraped bottom of tip, but you can't even see it unless you are under the car. This is obviously to be expected, it is used

who wants a sweet exhaust?

Ben

LetItSnow · 10-22-2005, 10:44 PM

dibs, cash in hand!

gtwagon941 · 10-23-2005, 02:31 AM

Quote:

Originally Posted by LetItSnow

dibs, cash in hand!

Long, lost cash in your hand. It just had an 11 month hiatus.

It is good that you'll finally get an exhaust setup. Ironically enough it will still be from your good buddy.

Jared

PHATsuby · 10-23-2005, 12:56 PM

LetItSnow, PM'd you, these are BE or BH specific, as in the BE is shorter than the BH, so they are not supposed to fit on each other interchangably. However, it would likely only require some tiny little piece of pipe to adapt it, or an extra flange, but it is up to you, just want to let you know as far as i know it is not a perfect bolt on fit for your wagon.

sorry man

Ben

LetItSnow · 10-23-2005, 01:02 PM

Per my PM, I'll take it anyway.

PHATsuby · 10-23-2005, 01:38 PM

SOLD!! Thanks LetItSnow

now, do you want a turbo kit to go with it

Ben

09-28-2005, 06:59 PM	#1
PHATsuby Scooby Guru Member#: 13617 Join Date: Dec 2001 Chapter/Region: MWSOC Location: MN Vehicle: 2001 Legacy GT back to stock is a project too	BE Brullen 2.5" Catback FS Hey fellow BE'ers, figured I would post here since It is so model specific, I am selling my turbo kit off as you know and I am also selling off my nice Brullen exhaust. It is 2.5" piping, with single 80mm tip, quiet acoustics(larger resonator). It sounds awesome, just putting on the one I made so this is coming off and will be available this weekend. These are full SS mandrel bend exhausts, bolts up to stock cat section. I will take pics when I get back this weekend. looking for 400 shipped(in the lower 48). if you have any questions let me know thanks Ben * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WTT:NY 3" SPT catback for 2.5" catback	singincanary	Tri-State Area Private Classifieds	16	04-22-2009 02:29 PM
Swap My Bosal 3" Catback 4UR 2.5" Catback?	jikhead	Engine/Power/Exhaust	6	09-20-2007 08:52 PM
FS: MRT Headers and Brullen 2.5inch Catback	Keith Cournoyer	New England Impreza Club Forum -- NESIC	23	02-09-2005 08:42 AM
FS-2.5" Catback Hi Temp Coated	MY99 2.5GT	Legacy Forum	10	06-26-2002 05:04 PM
Brullen 2.5" Stainless Cat-Back	traskw	Car Part Reviews	2	03-05-2002 10:58 PM

09-28-2005, 07:01 PM	#2
IDMO Scooby Newbie Member#: 91819 Join Date: Jul 2005 Chapter/Region: South East Location: Tampa Vehicle: 2004 FXT	would 2.5" piping have any ill effects on an n/a BE? i'd like to see pics when you get 'em

09-28-2005, 10:20 PM	#3
PHATsuby Scooby Guru Member#: 13617 Join Date: Dec 2001 Chapter/Region: MWSOC Location: MN Vehicle: 2001 Legacy GT back to stock is a project too	2.5" piping is on the larger side for NA applications, you would see more gains in the higher rpm ranges, but you may lose a bit of low end torque, I really dont know how siginificant it would actually be especially if you still had your stock cats creating the majority of the back pressure. I will get pics up this weekend. thanks Ben

09-29-2005, 12:56 AM	#4
MitchGT Scooby Specialist Member#: 73684 Join Date: Nov 2004 Chapter/Region: NWIC Location: Kirkland, WA Vehicle: 2012 4Runner	Any buyers for your turbo setup yet Ben?

09-29-2005, 05:11 AM	#5
PHATsuby Scooby Guru Member#: 13617 Join Date: Dec 2001 Chapter/Region: MWSOC Location: MN Vehicle: 2001 Legacy GT back to stock is a project too	Hey Mitch, someone has bought my Autronic, the mechanicals are still available though. Ben

09-29-2005, 01:02 PM	#6
MitchGT Scooby Specialist Member#: 73684 Join Date: Nov 2004 Chapter/Region: NWIC Location: Kirkland, WA Vehicle: 2012 4Runner	Any chance of a sound clip Ben?

10-22-2005, 05:19 PM	#7
PHATsuby Scooby Guru Member#: 13617 Join Date: Dec 2001 Chapter/Region: MWSOC Location: MN Vehicle: 2001 Legacy GT back to stock is a project too	well, finally got a chance to take some pics. so here they are. here is the only rear flaw that would possibly matter, scraped bottom of tip, but you can't even see it unless you are under the car. This is obviously to be expected, it is used who wants a sweet exhaust? Ben

10-22-2005, 10:44 PM	#8
LetItSnow Scooby Specialist Member#: 38222 Join Date: Jun 2003 Chapter/Region: Tri-State Location: Cicero, NY Vehicle: '10 &'12 Foresters another Miata convert	dibs, cash in hand!

10-23-2005, 12:56 PM	#10
PHATsuby Scooby Guru Member#: 13617 Join Date: Dec 2001 Chapter/Region: MWSOC Location: MN Vehicle: 2001 Legacy GT back to stock is a project too	LetItSnow, PM'd you, these are BE or BH specific, as in the BE is shorter than the BH, so they are not supposed to fit on each other interchangably. However, it would likely only require some tiny little piece of pipe to adapt it, or an extra flange, but it is up to you, just want to let you know as far as i know it is not a perfect bolt on fit for your wagon. sorry man Ben

10-23-2005, 01:02 PM	#11
LetItSnow Scooby Specialist Member#: 38222 Join Date: Jun 2003 Chapter/Region: Tri-State Location: Cicero, NY Vehicle: '10 &'12 Foresters another Miata convert	Per my PM, I'll take it anyway.

10-23-2005, 01:38 PM	#12
PHATsuby Scooby Guru Member#: 13617 Join Date: Dec 2001 Chapter/Region: MWSOC Location: MN Vehicle: 2001 Legacy GT back to stock is a project too	SOLD!! Thanks LetItSnow now, do you want a turbo kit to go with it Ben