Need new exhaust

Peter Hadfield · 08-24-2000, 08:55 PM

Does anyone know of a full stainless catback exhaust system that I can install on my 90 Legacy L sedan. Thanks for any input.

* Registered users of the site do not see these ads.

Peter Hadfield · 08-24-2000, 08:57 PM

Also I need the exhaust to be able to handle the added flow from a turbo or supercharger kit.

GTBGUY · 08-25-2000, 07:06 AM

I had a post several weeks ago for a 2.5" full-stainless steel cat-back... anyways, I have to find out if the hangers are the same (as well as the bends) for your car compared to the BD5/9 if it is then it'll be availible still for the group buy

Subie Gal · 08-25-2000, 07:41 AM

i just went to a strictly muffler shop and had them do mine... 2.5" cat back... tried to stay w/the original hangers and alleviate some of the bends...

j.

08-24-2000, 08:55 PM	#1
Peter Hadfield Scooby Newbie Member#: 1890 Join Date: Jul 2000 Location: Renton, Washington, USA Vehicle: 1990 Legacy L Sedan Champagne Rally Car #212	Need new exhaust Does anyone know of a full stainless catback exhaust system that I can install on my 90 Legacy L sedan. Thanks for any input. * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Needing New Exhaust Need Help	breezeby	Newbies & FAQs	4	12-10-2006 07:15 PM
need new exhaust	stisam80	Newbies & FAQs	1	05-08-2006 03:50 PM
EGT Install - need new exhaust gaskets?	koloumb	Factory 2.0L Turbo Powertrain	3	12-10-2002 03:05 PM
going turbo....need new exhaust	the spacecowboy	Normally Aspirated with bolt-on Forced Induction Powertrain	12	11-10-2002 03:48 PM
TurboXS Stage Unichip -- Need New Exhaust?	bedabi	Factory 2.0L Turbo Powertrain	14	10-17-2001 11:53 AM

08-24-2000, 08:57 PM	#2
Peter Hadfield Scooby Newbie Member#: 1890 Join Date: Jul 2000 Location: Renton, Washington, USA Vehicle: 1990 Legacy L Sedan Champagne Rally Car #212	Also I need the exhaust to be able to handle the added flow from a turbo or supercharger kit.

08-25-2000, 07:06 AM	#3
GTBGUY Scooby Specialist Member#: 2003 Join Date: Aug 2000 Location: Calgary, Alberta, Canada Vehicle: '99 BGP Legacy GT '98 QS Legacy L (auto)	I had a post several weeks ago for a 2.5" full-stainless steel cat-back... anyways, I have to find out if the hangers are the same (as well as the bends) for your car compared to the BD5/9 if it is then it'll be availible still for the group buy

08-25-2000, 07:41 AM	#4
Subie Gal GC84Ever Super Moderator Member#: 301 Join Date: Sep 1999 Chapter/Region: NWIC Location: WA Vehicle: 2001 2.5 RS/70 Van 02 WRX Rally Stud	i just went to a strictly muffler shop and had them do mine... 2.5" cat back... tried to stay w/the original hangers and alleviate some of the bends... j.