Welcome to the North American Subaru Impreza Owners Club Friday July 28, 2017
Home Forums WikiNASIOC Products Store Modifications Upgrade Garage
Go Back   NASIOC > NASIOC Technical > Electrical & Lighting

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.
* Registered users of the site do not see these ads. 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 01-24-2006, 11:52 AM   #1
Scooby Newbie
Member#: 93842
Join Date: Aug 2005
Location: Barbados
2001 Impreza WRX STi

Default Fix: How To Turn Off Rear Diff Light - STI Cluster Swap Into WRX

If someone has already figured this out, then my appologies for posting redundant information, but I couldn't find any fixes for this, only questions asking 'how to' and statements saying it can't be fixed, cause it's part of the STi's DCCD ciruit. Anyone who has swapped an STi gauge cluster into a WRX (or in my case a JDM 2004 STi cluster into a JDM 2002 STi) knows that one of the 'side effects' is the rear diff temp warning light does not go out. Some people have slipped a small piece of electrical tape under the overlay to block it, but I didn't want to do that, so some studying of the wiring diagrams and manual where in store for me. It turns out that the fix is simple , just ground the rear diff light terminal (B4 in i10 middle connector). The link below shows the rear diff temp light going on and off as I hold the wire to a ground and then remove it. http://member.newsguy.com/~gtfour/su..._rear_diff.avi

There is one catch. One my car (JDM 2002 STi), there wasn't a terminal in B4, so I either had to find a terminal from somewhere or look for another one that was not in use. I didn't bother with that route, and instead just remove the plastic cover at the back of the gauge, and then soldered a wire onto the leg for the B4 terminal, and ran this wire to a ground. WARNING: While the terminals on either side of B4 are both ground circuits, there are positive terminals in the i10 connector, so make sure your wire is soldered on properly. Also, try not to apply more heat than is necessary to the leg, or you may end up affecting the solder connection to the board. I also taped the wire to the back of the cluster so that any movement on the wire would not stress the solder joint.

As for where to ground the B4 wire, that's entirely up to you. I ran the wire down to the steering column where there was already a vacant hole for a 10mm bolt, and just added a ground eyelet and bolted it on there. There are other options, but please note I have not tried them. Splicing the B4 wire to the C6 wire (10 pin, single row, i11 connector), which is a ground, should also work. On my cluster, B27 and B28 where also grounds, but those may only be for the JDM models.

With this mod, the rear diff temp warning light will light up with ignition, and as soon as you start the car on, it will go out. I'm actually thinking about adding the rear diff temp switch. Why waste a perfectly good warning light, when it's as simple as running the same B4 wire to one terminal of the switch, and the other terminal to ground.

1990 Toyota Celica GT-Four
2001 Subaru Impreza WRX STi

Last edited by pioneer_sti; 02-07-2006 at 07:56 PM.
pioneer_sti is offline   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
'05 STi Cluster swap into '05 WRX - need actual install instructions WRblueX_Guy Electrical & Lighting 14 12-03-2016 12:26 AM
Honda S2000 cluster swap into WRX - help! austinramage Interior & Exterior Modification 98 10-11-2013 09:46 AM
04 sti cluster swap into 02 problems... skate enjoi Interior & Exterior Modification 16 05-27-2009 04:15 PM
Rear ended, lights stay on stylecat Newbies & FAQs 5 03-31-2007 10:45 PM
STI cluster swap into a WRX Gr8fulDave Warranty Issues & SOA Problems 14 08-01-2005 04:55 PM

All times are GMT -4. The time now is 04:35 PM.

Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2017 Axivo Inc.
Copyright ©1999 - 2017, North American Subaru Impreza Owners Club, Inc.