Welcome to the North American Subaru Impreza Owners Club Thursday October 19, 2017
Home Forums WikiNASIOC Products Store Modifications Upgrade Garage
Go Back   NASIOC > NASIOC Technical > Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo)

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.
* Registered users of the site do not see these ads. 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 06-21-2002, 10:35 PM   #1
Scooby Newbie
Member#: 19742
Join Date: Jun 2002
Location: Wheaton, IL
2002 WRX Sedan

Question Which is the correct way to reset the ECU??

1st way from MRT, this one makes sense and I think you could pull codes if you needed to:

MRT How to Tip
How to re-set your ECU unit.
ECU clear memory procedure is as follows for auto and manual transmissions:

With engine at operating temperature, turn engine off. Place gear shift lever into park (auto transmission cars only)
Locate the two ECU check connectors, for most cars they are located under the steering column and consist of a black plastic male and female connector, and a green male female connector. The exact location of the connectors varies with the different year models, but generally they are located under the steering column on the drivers side.
NOTE: sometimes they are still taped over with some small amount of plastic tape, so look hard, they will be there!
With the ignition OFF connect black to black and green to green.
Turn on ignition, do not start the engine, (and for auto transmission, cycle the gearshift lever from park to neutral and back to park ), depress the accelerator pedal to full throttle and hold for a few seconds, and then release.
Start engine and then drive for at least one minute, keeping road speed above 11 Km/h.
ECU is now re-set.
At this point the check engine light should start to flash the all clear signal (steady 1/2 second interval flashes). If the check engine light does not flash, or indicates some other sequence, there is a fault present in the system, and should be professionally checked for necessary repairs.
Once, stop the car and turn off the engine.
Disconnect the plugs.
Job complete

2nd way is to disconnect battery cable and reset the ECU and all radio stations

Is MRT's way just for UK cars?
z28dan is offline   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Which is the correct way to kill a zombie? reddoak Off-Topic 64 07-04-2009 11:49 PM
What is the correct way to attach harnesses to a harness bar? DiscoWagon Newbies & FAQs 2 06-18-2006 08:15 PM
v8 Brembos | What's the correct way to spread the pistons? TreyS Brakes, Steering & Suspension 9 11-15-2004 10:59 PM
What are the various ways to reset your ECU? macrwrx Newbies & FAQs 8 02-27-2004 01:12 PM
What is the correct way to make a fast corner when dricing a STD car.????? gerardchau Technical Forum Archive 3 09-19-2000 07:46 PM

All times are GMT -4. The time now is 02:33 AM.

Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2017 Axivo Inc.
Copyright ©1999 - 2017, North American Subaru Impreza Owners Club, Inc.