Welcome to the North American Subaru Impreza Owners Club Wednesday December 13, 2017
Home Forums WikiNASIOC Products Store Modifications Upgrade Garage
NASIOC
Go Back   NASIOC > NASIOC General > Member's Car Gallery

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.
* Registered users of the site do not see these ads. 
Reply
 
Thread Tools Display Modes
Old 09-30-2017, 02:16 AM   #401
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Since some of you enjoy the wiring pr0n... here's more....

Many break outs here..
Fat blue wire is 044 ground, with intank ground and misc grounds.
Blue/Gray are both rear speed sensors as well as hand brake, fuel temp and float.




1st breakout from the rear. 044 feed, meth relay connector as well as meth level float. O yeah..trunk release is purple.




Since I was experimenting with the boots.. I had to build up on the in-tank fuel pump breakout so it would shrink properly.



Some kapton tape right before boot application.



Both breakouts almost ready for epoxy and boot.



Power windows and power locks wrapped together.
Again with a build up so the original door grommet would seal properly.




Used some of the white cheaper heat shrink to wrap the door lock wiring.



Fender wiring wrapped alongside with sidemarker.
* Registered users of the site do not see these ads.
remski is offline   Reply With Quote
Sponsored Links
* Registered users of the site do not see these ads.
Old 10-13-2017, 11:35 PM   #402
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Onto the updates.

Coolant tank was finished. Painted and shaved.




Trunk harness is almost completed.



Battery+, fuel pump feed and tail junction.



044 harness merged.



Meth run on the right, washer on the left.



Main harness installed.



L+R wheel speed sensor along with hand brake switch.



Last but not least.. CAD designing the center console.
As in Cardboard Aided Design.

remski is offline   Reply With Quote
Old 10-15-2017, 12:49 PM   #403
Hyper
Scooby Guru
 
Member#: 15822
Join Date: Feb 2002
Location: MOCKBA
Vehicle:
1999 WRB GM6
2.12cc V9 Type RA

Default

What do you use the spec c tank for? I see it tapped for nylon hose
Also the 4l tank is for meth? I hear it doesn't long last with big injectors
Hyper is online now   Reply With Quote
Old 10-15-2017, 01:48 PM   #404
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Spec C is for meth.

Small tank is for windshield fluid.


Quote:
Originally Posted by Hyper View Post
What do you use the spec c tank for? I see it tapped for nylon hose
Also the 4l tank is for meth? I hear it doesn't long last with big injectors
remski is offline   Reply With Quote
Old 10-15-2017, 05:14 PM   #405
Hyper
Scooby Guru
 
Member#: 15822
Join Date: Feb 2002
Location: MOCKBA
Vehicle:
1999 WRB GM6
2.12cc V9 Type RA

Default

Ah
You should look into baffling the meth tank if you plan to do any racing
I am currently using surge tank in addition to spec c tank, but plan to ditch it in favor of some decent baffling
Hyper is online now   Reply With Quote
Old 10-16-2017, 12:16 PM   #406
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Tank did OK...
Low light came on when I had about 1/3 left.. so after 2 sessions I had to top it off.

I thought about baffling the thank but that would require opening it up..


Quote:
Originally Posted by Hyper View Post
Ah
You should look into baffling the meth tank if you plan to do any racing
I am currently using surge tank in addition to spec c tank, but plan to ditch it in favor of some decent baffling
remski is offline   Reply With Quote
Old 10-16-2017, 02:29 PM   #407
Scuby04STi
Scooby Specialist
 
Member#: 328635
Join Date: Aug 2012
Chapter/Region: NWIC
Location: Portland*
Vehicle:
2004 STi GTX3076R
Rally Blue

Default

Quote:
Originally Posted by remski View Post
Tank did OK...
Low light came on when I had about 1/3 left.. so after 2 sessions I had to top it off.

I thought about baffling the thank but that would require opening it up..

You don't need to "open it up" to add baffling, look up "baffling blocks" they work great. You just need to confirm the material used works with the fluid your tossing in the tank but you should be fine on that side of things.
Scuby04STi is offline   Reply With Quote
Old 10-19-2017, 12:37 PM   #408
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Oh... fuel foam... great idea..
Why i didnt think of it before...

Quote:
Originally Posted by Scuby04STi View Post
You don't need to "open it up" to add baffling, look up "baffling blocks" they work great. You just need to confirm the material used works with the fluid your tossing in the tank but you should be fine on that side of things.
remski is offline   Reply With Quote
Old 10-19-2017, 01:50 PM   #409
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Seems there is no foam that is alcohol safe..



Quote:
Originally Posted by remski View Post
Oh... fuel foam... great idea..
Why i didnt think of it before...
remski is offline   Reply With Quote
Old 10-19-2017, 06:04 PM   #410
Scuby04STi
Scooby Specialist
 
Member#: 328635
Join Date: Aug 2012
Chapter/Region: NWIC
Location: Portland*
Vehicle:
2004 STi GTX3076R
Rally Blue

Default

Quote:
Originally Posted by remski View Post
Seems there is no foam that is alcohol safe..

You have some fab/wiring skills but you could work on the whole google search thing, LOL.

Here: https://www.summitracing.com/parts/a...0/applications
Scuby04STi is offline   Reply With Quote
Old 10-20-2017, 12:22 AM   #411
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

I read few posts and gave up....
It scared me that even a little particle would clog up the meth injector.
Then we all know what happens next...

Thanks anyway... there is an option.

Quote:
Originally Posted by Scuby04STi View Post
You have some fab/wiring skills but you could work on the whole google search thing, LOL.

Here: https://www.summitracing.com/parts/a...0/applications
remski is offline   Reply With Quote
Old 10-20-2017, 12:23 AM   #412
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Its been quite a few years since I last have seen this.




I got DCCD hooked up and most of the lights taken care of.
Only one is the BRAKE light..
Looking at the diagram alternator feed should turn it off...

Also seems like I need the outside temp sensor alongside with some home made voltage controller...




Ah.. yes.. i'd be nice to reset the odometer...
remski is offline   Reply With Quote
Old 10-21-2017, 09:39 PM   #413
midnit
Scooby Newbie
 
Member#: 139435
Join Date: Feb 2007
Chapter/Region: South East
Location: Gulf Coast, FL
Default

Spent the last couple hours looking through this... so amazing! Subscribed!
midnit is offline   Reply With Quote
Old 10-22-2017, 06:47 PM   #414
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Glad you guys are enjoying it.

Quote:
Originally Posted by midnit View Post
Spent the last couple hours looking through this... so amazing! Subscribed!
remski is offline   Reply With Quote
Old 10-30-2017, 12:04 AM   #415
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Spent some time working on the cluster wiring.



All connections wrapped.



And few hours later... Its complete.
remski is offline   Reply With Quote
Old 11-05-2017, 07:54 PM   #416
Russell Rogers
Scooby Specialist
 
Member#: 27261
Join Date: Oct 2002
Chapter/Region: NWIC
Location: Wa
Vehicle:
1999
I'm Ron Burgundy?

Default

Just waiting for the weekly update
Russell Rogers is offline   Reply With Quote
Old 11-09-2017, 11:51 PM   #417
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Lately I've been demotivated....
I've managed to break the alternator that i put 5hrs into..



Quote:
Originally Posted by Russell Rogers View Post
Just waiting for the weekly update
remski is offline   Reply With Quote
Old 11-13-2017, 11:18 PM   #418
WhatLipIsThat
Scooby Newbie
 
Member#: 477678
Join Date: Nov 2017
Location: Nevada
Vehicle:
1993 Impreza L
Satin White Pearl

Default

The amount of work that has gone into this thing is absolutely incredible!
WhatLipIsThat is offline   Reply With Quote
Old 11-14-2017, 02:14 AM   #419
Shipman
Scooby Guru
 
Member#: 312847
Join Date: Mar 2012
Chapter/Region: Tri-State
Location: MD
Vehicle:
2006 WRX STi
2008 Legacy/2003 Forester

Default

I've said it before and I'll say it again. This is legit the only real build thread worth reading through on this site.
Shipman is offline   Reply With Quote
Old 11-14-2017, 06:11 PM   #420
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Thanks, that means a lot.

I need all the motivation I can get !!!!

Quote:
Originally Posted by Shipman View Post
I've said it before and I'll say it again. This is legit the only real build thread worth reading through on this site.
remski is offline   Reply With Quote
Old 11-19-2017, 09:14 PM   #421
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Time for long overdue updates.

Some glue, few days of itching and finally we have a center console.




Here it is installed, sitting pretty.



Cluster was installed and new wiring is on its way.



Finally reached a milestone ...
For the first time the car was powered on.
It was just a heater fan :biglaugh: but the car now has power.
remski is offline   Reply With Quote
Old 11-19-2017, 11:35 PM   #422
TheBlackPowder
Scooby Newbie
 
Member#: 477628
Join Date: Nov 2017
Chapter/Region: MWSOC
Location: Fargo, ND
Vehicle:
2006 Impreza WRX Li
Steel Gray Metallic

Default

She is nice
TheBlackPowder is offline   Reply With Quote
Old 11-22-2017, 09:43 PM   #423
remski
Scooby Newbie
 
Member#: 151895
Join Date: Jun 2007
Default

Day in .. day out...


The birth of yet another wiring harness.



This will feed the brake pedal, clutch and all the buttons on the steering wheel.



Reay for the 24gauge motec connections.
This is just a signal to ground so gauge can be tiny.




This harness is done for now... Also feeds the heater fan and power locks...
Almost forgot.. windshield washer and the horn.




A well hidden trunk release solenoid.



Power windows and power locks harnesses were merged.
Now all I need is the connector for that BMW windows switch..




Last but not least.. DCCD/cluster connector was completed..
Sooo nice to see the cluster on.

Btw.. I've decided not to switch to Subaru's DCCD controls.
So.. both switches are for sale if anybody wants.




Things are becoming organized.. right ?
remski is offline   Reply With Quote
Old 11-24-2017, 12:14 AM   #424
meinct
Scooby Specialist
 
Member#: 350408
Join Date: Mar 2013
Chapter/Region: NESIC
Location: Windsor Locks, Ct
Vehicle:
2012 wrx
dgm

Default

Keep it up man. You're doing an awesome job. Can't wait to see the finished product.
Happy Thanksgiving!
meinct is offline   Reply With Quote
Old 11-24-2017, 02:51 PM   #425
Russell Rogers
Scooby Specialist
 
Member#: 27261
Join Date: Oct 2002
Chapter/Region: NWIC
Location: Wa
Vehicle:
1999
I'm Ron Burgundy?

Default

I love this thread! Keep it up!
Russell Rogers is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 03:22 PM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2017 Axivo Inc.
Copyright ©1999 - 2017, North American Subaru Impreza Owners Club, Inc.