Gtx 3076r gen 2 vs gtx3582r gen 2 ej207

[Mauled]

Alright here's my question if I get the 3582 gtx what ar should I run to hit 500whp, .63 or .82? I have 264 cams and can I turn the rpm limit to 8500?

* Registered users of the site do not see these ads.

[HughGordon]

Originally Posted by Mauled

Alright here's my question if I get the 3582 gtx what ar should I run to hit 500whp, .63 or .82? I have 264 cams and can I turn the rpm limit to 8500?

.82 should do it. Do you have upgraded valve springs and retainers as well? How about rod bolts? When I had my block built I was told arp 2000 are good for 8k and above that you'd want arp +625 but that was for an ej257. The ej207 has an 8k rev limit right? You could always up the rev limit and see if it still makes power past 8k. Why not try the 3576r though like other people have suggested?

[K3rm1tth3fr0g]

3576 Gen 2 is worth looking into if you aren't going G series. I have one in my garage, it's a great turbo.

G30 770 should beat it for spool though

.82 will hold power up top longer

[HughGordon]

https://www.pulsarturbo.com/product/...hp-rating-770/

How about this guy?

[K3rm1tth3fr0g]

Does not share the same TW specs as the aforementioned G30 770.

G30-770:

Compressor: 58mm/71mm
Turbine: 60mm/55mm

5862G:

Compressor Wheel: 58mm/71mm
Turbine Wheel: 68/62mm

And what do ya know?

Almost exactly as I stated, the knock off comes in at most of the cost of the real unit.

Originally Posted by K3rm1tth3fr0g

Good knock off turbos are virtually non existent without spending ~65%+ of the cost of the real product.

This is even more true with the ultra cutting edge tech like the G series....

770s can be had for ~$1800 and this unit is $1059

Up to the user if those savings are worth receiving worse support, and experiencing overall lowered performance.

[HughGordon]

I know it's not the same turbine wheel, that's why I think it's an interesting turbo. Similar to the 3576 gen ii but with a smaller exducer on the compressor vs the g35-900 which is the successor and has a larger inducer in comparison to the 58/76 wheel on the 3576. Garrett doesn't offer that specific wheel combo. Also, can show me where you can buy a G30-770 for $1800? Because all I can find are supercores for that price.

[Mauled]

Originally Posted by HughGordon

.82 should do it. Do you have upgraded valve springs and retainers as well? How about rod bolts? When I had my block built I was told arp 2000 are good for 8k and above that you'd want arp +625 but that was for an ej257. The ej207 has an 8k rev limit right? You could always up the rev limit and see if it still makes power past 8k. Why not try the 3576r though like other people have suggested?

Yeah fully built heads gsc billet cams and arp 625. When I pulled the heads off the cylinders looked perfect so I didn't split the block, still stock version 8 bottom end.

Here is the turbo I have now: https://www.ebay.com/itm/174006332113?hash=item288395ead1:g:jw4AAOSwFpddX3M 4&amdata=enc%3AAQAIAAABAE6YKQz5eMB2ezHPP%2BdRiVTSZ MHITCmCYWhrUJqLrBR0wswLtkvxe%2FUEg4G30IYnLhxN%2Bt1 Slt6I400YkE1joS0mOGICH%2BrVpbJbpfgFBJxrXV%2BpPW3YF HuouVRM8LZjdM%2B6%2FxTdC7RYfhhvNcL6QUnbXOGvRoyE2bW KAAfWf7ldw1G6toWIH41NfVzzqzz1J4TGE4L3zvFLYO05chIvh hE3aq%2B4cfQM84CgZHkh3mVIu%2FRZLPT4QlebzqhE0K7WVGx 8t7UPtBSjShlri2VzE2fN8%2FUW6ONHKk%2Br7gvQzE53wqrQH 41GQECVFQe9XypjpJZbUjU4VETH%2BDKgfbJvzY4%3D%7Ctkp% 3ABFBMypryzopi

Like fuji said I don't think the 3576 will hit 500whp unless I use 30psi of boost. Figured if I'm going to get a bigger turbo the next step up is 35r.

[HughGordon]

How about a G35-900 clone from that same company? Or is that too pricey? Similar flow-wise to the 3582 but more efficient.

https://www.ebay.com/itm/18523315362...3ABFBM_rXC0Ipi

[HughGordon]

I'm sorry for going off on you yesterday Kermit.

Originally Posted by K3rm1tth3fr0g

China has good and bad labor practices. It's not as simple as, China labor bad.



You're upset because the gaskets that came with were bad....?

Who uses included gaskets anyway?

Hahaha - no one is gatekeeping anything.

That is rich coming from a goober who contributes nothing to the forum.

[Mauled]

Double post

[Mauled]

Originally Posted by HughGordon

How about a G35-900 clone from that same company? Or is that too pricey? Similar flow-wise to the 3582 but more efficient.

https://www.ebay.com/itm/18523315362...3ABFBM_rXC0Ipi

It would have to be t3 4 bolt instead of v band, I have the perrin rotated uppipe and downpipe. I'll have to see if I can find one and look up more data on the turbo.

[HughGordon]

Originally Posted by Mauled

It would have to be t3 4 bolt instead of v band, I have the perrin rotated uppipe and downpipe. I'll have to see if I can find one and look up more data on the turbo.

Maybe you can fit an adapter in there? I don't think you can get a G-series with the 4 bolt, even clones. I had Joey at CustomFabShop.com make me an adapter that goes v-band turbo exhaust to stock Subaru downpipe flange. Nice guy and does good work, he can make any flange or adapter that you can think of.

https://customfabshop.com/product/t3...-turbocharger/

[Alistairh]

Please show me where I can get a new g30-770 with turbine housing for $1700.

[stiaddict07]

Originally Posted by K3rm1tth3fr0g

Couldn't agree more

G30 770 is the ultimate SWEET spot for ~500+

Gt30 spool and response with gt35 power

Can the G30 770 fit in stock location?

[HughGordon]

You can make it fit with adapters. OP has a rotated setup though.

[subaru_gc8]

Originally Posted by stiaddict07

Can the G30 770 fit in stock location?

no you're going to have to go rotated, the g series are a lot bigger and heavier than the gtx series

[HughGordon]

Originally Posted by subaru_gc8

no you're going to have to go rotated, the g series are a lot bigger and heavier than the gtx series

Not true. They are almost identical in size. Yes in most cases you'd have to go rotated unless you have some adapters fabricated and grind your block.