|
|
|
|
Thread Tools | Display Modes |
04-08-2010, 12:13 PM | #1 |
Scooby Specialist
Member#: 178426
Join Date: Apr 2008
Location: FoCo
Vehicle:2010 S4 Gray |
2.0 + Dom 3.0XT-R + E85 makes 392whp
Event: dyno pull
Location: The Boost Creep, Mead CO Ambient Temp: Elevation: 5000 Weather: sunny, cool Track and Conditions: NA Tires: stock rims with blizzaks Car: 02 WRX Tuner: Harvey, The Boost Creep Dyno Info: Dyno Dynamics [color=black]Peak HP: 392 on E85, 350 on pump CF 1.15 Peak Torque at RPM: 310 Baseline hp/tq for a stock on same dyno: 2.0 160whp Target Boost: 27 Target AFR: Fuel: E85 Engine/Power Modifications: ej207 short block: JE pistons Eagle Rods crank drilled balanced nitride coated crank ej205 heads with BC: Valves Springs Retainers 272 Cams APS 525 fmic, Borla hush catback, 1000cc DW, Perrin Fuel Rails, Perrin Big maf, grimmspeed everything, tial 38mm ewg, invidia dp, walbro 255, APS 50/50 bov, ATI damper, zeitronix map, samco inlet, Apexi AVCR Driveline Modifications: ACT streetlite flywheel, ACT sprung six puck, RA gear set, Group N engine mounts Suspension Modifications: Tein basic coilovers, hotchkiss swaybars and endlinks 91 octane, 22psi E85, 27psi Runs very well on the street. Transitions nice, spools quicker than the dyno (4800rpm on the street), although it does take a second to spool even when dropping down gears. Actually makes for a very nice DD, much to my surprise. Powers there if I want it, just have to go get it. It does sounds absolutely amazing. All in all, I like it. I figured no matter what I would have a high strung engine, which I enjoy. Debating whether or not to raise the rev limiter, maybe get another 500rpm out of it. For now though, this is just fine.
* Registered users of the site do not see these ads.
Last edited by rexblake; 07-18-2010 at 08:56 PM. |
04-08-2010, 12:19 PM | #2 |
Scooby Newbie
Member#: 170973
Join Date: Feb 2008
Location: nashville
Vehicle:2004 WRX 4EAT PSM |
holy-lag!
If your happy that is all that matters, but it seems to me you could've gotten a different turbo to make that power on the 2.0L EJ207 with at least 1000 RPM quicker spool up. The XT-R has a 10cm exhaust housing correct? That's just massive for a 2.0L.... What is a safe redline for your motor? |
04-08-2010, 12:27 PM | #3 |
Scooby Specialist
Member#: 178426
Join Date: Apr 2008
Location: FoCo
Vehicle:2010 S4 Gray |
Yeah, lag was expected. Harvey mentioned that all gt3076 variants spool around 5500 on his dyno. I knew going in it was going to be laggy. But, I wanted top end power, and I definitely have that.
I highly doubt I could have gotten anywhere close to this kind of power with a smaller turbo. In fact, no chance in hell. My 68hta only put down 342 on the same kind of dyno. Both dynos are withing 10whp for stock cars. I could get better spool by twinscrolling and going rotated, maybe another 500rpm or so. That's about the only option though. Safe redline is debatable. The guys in japan are running the ej207 to 8200 on track days. Some here in the states are going to 8500, just have to watch out for oiling issues. The engine and heads should be able to take it to 9k, but I think that would be asking for trouble, I wouldn't go above 8500. Last edited by rexblake; 04-08-2010 at 12:36 PM. |
04-08-2010, 12:31 PM | #4 |
Scooby Guru
Member#: 36033
Join Date: Apr 2003
Chapter/Region:
SCIC
Location: Tuning Lab
Vehicle:CEO PhatBottiTuning 2006 STi GTX3582 + Meth |
idk man....seems really really really laggy. if you're gonna run e85 all the time you should just switch back to a tmic.....
|
04-08-2010, 12:41 PM | #5 |
Scooby Specialist
Member#: 178426
Join Date: Apr 2008
Location: FoCo
Vehicle:2010 S4 Gray |
That's not a bad idea. Maybe down the road if I get sick of the lag.
|
04-08-2010, 01:01 PM | #6 |
Scooby Newbie
Member#: 243533
Join Date: Apr 2010
Chapter/Region:
TXIC
Location: texas/Huntley, Il
Vehicle:02 wrx-mfctry-stg2 |
lag bot
|
04-08-2010, 01:33 PM | #7 |
Scooby Guru
Member#: 36033
Join Date: Apr 2003
Chapter/Region:
SCIC
Location: Tuning Lab
Vehicle:CEO PhatBottiTuning 2006 STi GTX3582 + Meth |
i would do 3 experiments on your car.
1 - get a different BOV......preferably switch back to a bpv. 2 - take the line off your wastegate and see what the boost does 3 - incase you are scared to do #2.....hook a hallman mbc up and see how your boost does without the avcr. |
04-08-2010, 02:16 PM | #8 |
Former Vendor
Member#: 26933
Join Date: Oct 2002
Chapter/Region:
BAIC
Location: Fairfield, CA
Vehicle:2006 STI CGM |
That's really a poor choice of exhaust housings for that application and turbo. With the EWG, you can actually get away with running a very small exhaust housing and still flow enough to make good power. I would be willing to bet that an 8cm housing will spool the turbo a good 700-800RPM sooner and easily make within 10whp of the current power levels. Hell, you could even flow that power through a 7cm housing + EWG and get 1000RPM quicker spool and GREATLY improved transient response without losing significant power at all.
I just don't understand this move to the giant exhaust housings for relatively small compressors. Why would you want to give up response without gaining any significant power capability? -- Ed |
04-08-2010, 02:46 PM | #9 |
Scooby Guru
Member#: 56203
Join Date: Feb 2004
Chapter/Region:
Tri-State
Location: south nj
Vehicle:00 RSTI Coupe Twin Scroll 2.5XTR EJ207 |
was the 91pump graph done in 1st gear?
|
04-08-2010, 03:40 PM | #10 |
Former Vendor
Member#: 26933
Join Date: Oct 2002
Chapter/Region:
BAIC
Location: Fairfield, CA
Vehicle:2006 STI CGM |
|
04-08-2010, 04:12 PM | #11 |
Scooby Guru
Member#: 103232
Join Date: Dec 2005
Chapter/Region:
Tri-State
Location: GTX3576R 05GD, GTX3076R'd FXT
Vehicle:GTX 3071R'd 11WRX PPG,4.44,LSD,E85,6spdx3 |
First of all I glad to hear the car feels good.
Ed do you feel the same way about the 10cm the same way about the 2.5 with worked heads and cams? Im thinking about swapping from the 8cm to the 10cm housing on my dom3. Not the whole XT-R upgrade, just the turbine housing. Sorry to jack your thread. |
04-08-2010, 04:46 PM | #12 | |
Former Vendor
Member#: 26933
Join Date: Oct 2002
Chapter/Region:
BAIC
Location: Fairfield, CA
Vehicle:2006 STI CGM |
Quote:
-- Ed |
|
04-08-2010, 05:15 PM | #13 | |
Scooby Specialist
Member#: 147579
Join Date: Apr 2007
|
Quote:
I asked Blouch to make me a 3.0 XT-R with an 8cm hotside but they declined . Maybe I can have it done at a tuner shop... |
|
04-08-2010, 08:19 PM | #14 |
Scooby Guru
Member#: 82745
Join Date: Mar 2005
Chapter/Region:
SCIC
Location: So Cal
Vehicle:2005 Subaru STI 2003 EJ207 S204 Wagon |
You have very little usable power band on 91 pump. Also, hurting you is the non-avcs heads and cam. I have to agree with the others, that the Dom 3 xt-r 10cm is too large for your setup.
I was able to make 324whp/300whp on my 2.0L with stock heads, cams, airbox, iwg, cat, and sti tmic on 91 pump with the Tomei single scroll 7760 turbo. http://forums.nasioc.com/forums/show....php?t=1962172 I think i can make 340-350ish whp with 70+mm cai, ewg, and larger TMIC and between 380-390+ whp on e85 (including the additional mods). I think you'll make the same peak power as you make now, but with a more usable powerband with a smaller turbo. Something along the lines of a 20g |
04-08-2010, 08:50 PM | #15 | |
Former Vendor
Member#: 26933
Join Date: Oct 2002
Chapter/Region:
BAIC
Location: Fairfield, CA
Vehicle:2006 STI CGM |
Quote:
-- Ed |
|
04-09-2010, 01:51 AM | #16 |
Scooby Guru
Member#: 3687
Join Date: Jan 2001
Chapter/Region:
MWSOC
Location: St. Paul, MN
Vehicle:MY99 GF4 JDM 6spd NF Performance |
is this the final tune???
|
04-09-2010, 02:52 AM | #17 | |
Scooby Specialist
Member#: 178426
Join Date: Apr 2008
Location: FoCo
Vehicle:2010 S4 Gray |
Quote:
As for the dom 3 with the 8cm housing, harvey has one on his car with a 2.5 and makes 30whp less than me. Same dyno. The 91 map is solely for transition purposes. I run E85 year round. That's what it wanted to do without adjusting timing crazy or boost. I don't understand why people are surprised at the lag on this motor. At altitude, 2.0, 2.4inlet with a fmic. Pretty much right where it was expected to be. If I get really sick of the lag I can always throw the 68hta back on with a larger exhaust side. So far, it has just as much power putzing around town with much higher top end. Don't see the issue, just have to get used to it. |
|
04-09-2010, 11:20 AM | #18 |
Former Vendor
Member#: 26933
Join Date: Oct 2002
Chapter/Region:
BAIC
Location: Fairfield, CA
Vehicle:2006 STI CGM |
The 68hta has a much smaller compressor than the Dom 3 so of course it will make significantly less power. I'm talking about running the same compressor with a smaller hot side. As long as you're running an EWG, you shouldn't lose much power potential at all.
-- Ed |
04-09-2010, 12:19 PM | #19 |
Scooby Specialist
Member#: 178426
Join Date: Apr 2008
Location: FoCo
Vehicle:2010 S4 Gray |
I understand the 68hta is going to make less power. What I'm saying is that with the 7cm hot side I had no top end power. None, zilch, nada. It spooled at 4k and dropped at 6500, which gave me a 2500rpm power band.
I logged last night, full spool by 4800 on the street. Which gives me a 3200rpm power band with much more power. Hopefully I can adjust the avcr some more and see if I can't get it spooling even quicker. |
04-09-2010, 01:08 PM | #20 |
Scooby Guru
Member#: 36033
Join Date: Apr 2003
Chapter/Region:
SCIC
Location: Tuning Lab
Vehicle:CEO PhatBottiTuning 2006 STi GTX3582 + Meth |
just disconnect the wastegate and go WOT and see if you spool faster......then you know its the avcr settings.
dont do a full pull as you wouldnt have any boost control....but it will show you if the avcr is holding u back |
04-09-2010, 01:11 PM | #21 |
Former Vendor
Member#: 205916
Join Date: Mar 2009
Chapter/Region:
South East
Location: I SELL ENGINE PARTS!
Vehicle:2003 Subaru WRX in the 10's and the bends |
Good advice, that's how I do the spool up tuning on my car. You definitely have to watch the boost gauge though, and catch it before it makes all the boost it wants.
|
04-09-2010, 01:46 PM | #22 | |
Former Vendor
Member#: 26933
Join Date: Oct 2002
Chapter/Region:
BAIC
Location: Fairfield, CA
Vehicle:2006 STI CGM |
Quote:
Here's an example. This is an STI I tuned several years ago with an FP Red with a 7cm exhaust housing running an EWG tuned on C16 at about 30psi: As you can see, the 7cm housing with an EWG is capable of flowing quite a bit more air than your setup while still providing exceptional spool for the size of the compressor and the power capability. This is obviously not an apples to apples comparison; it just shows that the size of the exhaust housing on your 68hta was not necessarily the limiting factor. Thanks -- Ed Last edited by Equilibrium Tuning; 04-09-2010 at 01:51 PM. |
|
04-09-2010, 02:14 PM | #23 |
Scooby Specialist
Member#: 108089
Join Date: Feb 2006
Chapter/Region:
MWSOC
Location: Minnesota
Vehicle:2003 WRX NF Performance |
i don't know what to say....
|
04-09-2010, 03:20 PM | #24 |
Scooby Newbie
Member#: 14116
Join Date: Jan 2002
|
The HTA68 uses TD05H turbine, so you can't really compare housing sizes, it also depends on the turbine wheel which is used. In my opinion the HTA68 is just at the limit for a 7cm turbine housing with TD05H turbine wheel. Any bigger compressor (in combination with the TD05H turbine) and a 8cm housing gives more power.
The DOM would perform much better on this 2.0 liter engine with a 8cm turbine housing. |
04-09-2010, 04:04 PM | #25 |
Scooby Newbie
Member#: 12694
Join Date: Nov 2001
Location: Under my car
Vehicle:02 WRX/JDM EJ207RA Unabomber Eeee-thug |
What really matters is how the car feels on the road.... Care to elaborate?
Tom |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Dom 3.0XT-R and Dom 4.0XT-R Dyno Charts | Blouchturbo | Proven Power Bragging | 485 | 09-19-2021 09:40 AM |
Dyno Tune: IAG makes 409whp on 2.5L + Prototype Blouch DOM 3.0 XT-R | IAG Performance | Proven Power Bragging | 155 | 07-13-2011 07:06 PM |
370WHP alternative to Dom 3.0XT-R | turboICE | Factory 2.5L Turbo Powertrain (EJ Series Factory 2.5L Turbo) | 29 | 06-07-2010 12:04 AM |
Dom 3.0XT-R and Dom 4.0XT-R Now Available | Blouchturbo | Engine/Power/Exhaust | 17 | 02-04-2010 02:01 AM |
FS: Nav Software ver 2.0 & 3.0 east and west | dahane | Interior/Dressup/Audio & Security | 2 | 10-29-2008 03:10 PM |