Welcome to the North American Subaru Impreza Owners Club Saturday March 6, 2021
Home Forums Images WikiNASIOC Products Store Modifications Upgrade Garage
Go Back   NASIOC > NASIOC Technical > Engine Management & Tuning

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.

* As an Amazon Associate I earn from qualifying purchases. 
* Registered users of the site do not see these ads. 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 09-01-2016, 11:04 PM   #1
Scooby Specialist
Member#: 148974
Join Date: May 2007
Chapter/Region: SCIC
Location: San Diego
2010 4x4 Silverado

Default Logging AFR with AP v3 and AEM UEGO - How to wire it up.

When I asked Phatron if I could log my AFR with my AP v3, he sent me the link to a kit sold by Moore Performance, but it comes with a relay and extra wiring that you don't need and can't justify spending $85 on. Overkill for just trying to log AFR on your Cobb Accessport. All you need to do is tap your AEM UEGO's 5v output into the correct wire that the ECU would normally use to read off of the Rear O2 sensor (or TGV Left/TGV Right) and then configure the Custom Sensor Input in Accesstuner.

I considered going straight to the harness coming out of the ECU, but opted to go with where I had a little more room while the engine was out which was right at the top of the transmission where there is a connection between two plugs. You may find it easier to tap in at a different location, say, further down the line towards the bottom of the car, or the other direction closer to the firewall.

Plug for the Rear O2 sensor on top of transmission (you may also use TGV Left or TGV Right).

We want the wire that communicates voltage changes from the rear O2 sensor to the ECU, which is the solid white wire on the 2008+ STi (check your year)

Reconnect the plug. *kind of important, haha

I fed the wire through boot for the Right Hand engine harness, then silicone'd over the slit I made. The wire will come through behind the glovebox area.

My AEM UEGO gauge's 12v ACC source is tapped into the radio harness and grounded nearby. The 5v output wire for logging (also conveniently a solid white wire) will connect to the yellow wire that we just routed behind the radio.

Make the necessary changes to your map for AEM UEGO scaling before monitoring. (helpful link from Cobb )

Log/monitor the parameter "Sensor Input Monitor Only (Rear O2)" or "Sens Only Rear O2" on your AP v3

*Note - you can also use TGV Left or TGV Right for monitoring and logging. Just depends on what you want to tap into, and what might make for the easiest access.

**Note - Just another note to anyone installing a AEM X-Series Wideband UEGO with the Bosch LSU 4.9 sensor, you also need to ground the BROWN wire for analog sensor ground. Otherwise it wont output 0-5v to the ecu.

Last edited by SurfGuruJeff; 10-15-2016 at 03:24 PM.
SurfGuruJeff is offline   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 01:55 PM.

Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2021 Axivo Inc.
Copyright ©1999 - 2019, North American Subaru Impreza Owners Club, Inc.

As an Amazon Associate I earn from qualifying purchases.