Welcome to the North American Subaru Impreza Owners Club Tuesday October 15, 2019
Home Forums WikiNASIOC Products Store Modifications Upgrade Garage
NASIOC
Go Back   NASIOC > NASIOC General > Interior & Exterior Modification

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.







* As an Amazon Associate I earn from qualifying purchases. 
* Registered users of the site do not see these ads. 
Reply
 
Thread Tools Display Modes
Old 05-12-2019, 11:56 AM   #26
ChristopherWRX
Scooby Newbie
 
Member#: 486706
Join Date: Jun 2018
Location: MD
Vehicle:
2016 WRX
Lapis Blue Pearl

Default

Looks good mpen97!
* Registered users of the site do not see these ads.
ChristopherWRX is offline   Reply With Quote
Sponsored Links
* Registered users of the site do not see these ads.
Old 05-18-2019, 05:00 PM   #27
Wolfman_Jack
Scooby Newbie
 
Member#: 296372
Join Date: Sep 2011
Chapter/Region: NESIC
Default

mpen97, where did you get that fill in part for the DCCD?
Wolfman_Jack is offline   Reply With Quote
Old 06-02-2019, 02:16 AM   #28
c1em3ntchua
Scooby Newbie
 
Member#: 459594
Join Date: Dec 2016
Default

Looks to be 3D printed. I'm looking for one of these as well.
c1em3ntchua is offline   Reply With Quote
Old 06-05-2019, 09:14 PM   #29
crunktim
Scooby Newbie
 
Member#: 245067
Join Date: Apr 2010
Default

Just got this done through Jason at Overland designs. Did a great job.

crunktim is offline   Reply With Quote
Old 06-06-2019, 09:48 PM   #30
Jnak001
Scooby Newbie
 
Member#: 456734
Join Date: Oct 2016
Default

I swapped this in about a year ago in my 2017. I found a guy local who designed and 3D printed the coin tray to replace the DCCD controller. To keep coins from rattling to much I cut a small section of tool box tray liner and placed it in the bottom of the tray.
Jnak001 is offline   Reply With Quote
Old 06-14-2019, 12:19 PM   #31
crunktim
Scooby Newbie
 
Member#: 245067
Join Date: Apr 2010
Default



Finished product.
crunktim is offline   Reply With Quote
Old 06-19-2019, 05:26 PM   #32
lowvndslow
Scooby Newbie
 
Member#: 498273
Join Date: Feb 2019
Default

Wait so can I just buy the cup holder piece and swap it out? Do I just need to buy one item?
lowvndslow is offline   Reply With Quote
Old 06-19-2019, 07:52 PM   #33
dannyq86
Scooby Newbie
 
Member#: 416919
Join Date: Mar 2015
Chapter/Region: SCIC
Location: SoCal
Default

@crunktim looks badass, and expensive
dannyq86 is online now   Reply With Quote
Old 06-20-2019, 12:45 PM   #34
Big-E
NASIOC Supporter
 
Member#: 123843
Join Date: Aug 2006
Chapter/Region: NESIC
Location: Connecticut
Vehicle:
2016 STI LTD CWP
Let LED's light your way!

Default

Quote:
Originally Posted by lowvndslow View Post
Wait so can I just buy the cup holder piece and swap it out? Do I just need to buy one item?
https://parts.subaru.com/a/Subaru_20...10-930-01.html
Big-E is offline   Reply With Quote
Old 06-20-2019, 01:43 PM   #35
penak
Scooby Newbie
 
Member#: 498498
Join Date: Mar 2019
Default

Loving this thread, very interesting discussion
penak is offline   Reply With Quote
Old 06-21-2019, 12:14 PM   #36
Jnak001
Scooby Newbie
 
Member#: 456734
Join Date: Oct 2016
Default

If you have heated seats the switches and wire harness connections for the STI are different than a WRX so they are not plug and play. I had to cut the opening out to fit the stock WRX switches. I ended up buying a complete STI center console on eBay with the DCCD controller. I turned around and sold the DCCD controller and other parts that I didnít need to offset a majority of the cost.
Jnak001 is offline   Reply With Quote
Old 06-27-2019, 10:21 PM   #37
Lone Wolf 75
Scooby Specialist
 
Member#: 2221
Join Date: Aug 2000
Chapter/Region: MAIC
Location: White Marsh, MD
Vehicle:
2018 Subaru WRX
Lapis Blue Pearl

Default

Quote:
Originally Posted by crunktim View Post


Finished product.
That's beautiful. I want one but it's hard to justify. I'm wrestling with this and the JDM leather shift console like the S4's.
Lone Wolf 75 is offline   Reply With Quote
Old 07-23-2019, 09:36 AM   #38
c1em3ntchua
Scooby Newbie
 
Member#: 459594
Join Date: Dec 2016
Default

Hey guys, some updates.

I chatted with mpen97 on Reddit, and he sent me the 3D model of the coin tray that he designed. I have made some improvements based on the model that he created (download links below):
  1. Slightly enlarged the tray.
  2. Contoured the "overhangs".
  3. Added 4 clips and 2 screw holes (based on the SI Drive design).

Things I did:
  1. Printed in ABS, 100% infill due to the clips and screw holes. Two clips (both on the same side) broke off while test fitting the model, but the other two clips and the screws held the tray in quite well.
  2. My model was printed at 102% scale, I'm guessing anywhere from 101-102% should be good as ABS contracts after printing.
  3. Sanded the top surface of the "overhang" and spray painted the tray matte black.

Download links to model:
  1. 3mf: https://www.dropbox.com/s/46kp09rwtq..._V4.2.3MF?dl=0
  2. stl: https://www.dropbox.com/s/stneiim4xp..._V4.2.STL?dl=0

Finally, some pictures!



c1em3ntchua is offline   Reply With Quote
Old 08-05-2019, 11:01 AM   #39
LubeySubie15
Scooby Newbie
 
Member#: 470452
Join Date: Jul 2017
Default Apologizing for the extremely late reply to this thread

Quote:
Originally Posted by mpen97 View Post
Full swap complete on my 2016 WRX Premium! (Excuse the mess... overdue for a clean)

I have just swapped the STi shift trim and want the exact same setup you have for the sliding cup holder minus the DCCD controller, any guidance as far as how you went about getting that? I have a 16 wrx as well, thanks !
LubeySubie15 is offline   Reply With Quote
Old 08-05-2019, 11:22 AM   #40
gmasters428
Scooby Newbie
 
Member#: 464431
Join Date: Mar 2017
Default

That looks great
gmasters428 is offline   Reply With Quote
Old 08-09-2019, 09:40 AM   #41
mpen97
Scooby Newbie
 
Member#: 501048
Join Date: May 2019
Chapter/Region: International
Vehicle:
2016 WRX Premium
WRB

Default

Quote:
Originally Posted by LubeySubie15 View Post
I have just swapped the STi shift trim and want the exact same setup you have for the sliding cup holder minus the DCCD controller, any guidance as far as how you went about getting that? I have a 16 wrx as well, thanks !
I went to a local wrecker and bought the centre console, which includes the sliding cup holder. Pretty simple removal. One screw underneath the handbrake boot and two screws at the bottom of the centre console, inside the arm rest. Pop that off, unplug the 12v socket from underneath before yanking the console out and it's as easy as that.

In terms of replacing the DCCD. See c1em3ntchua's just above yours. We worked on the coin tray and, I guess, perfected it, to fit. A download link is available for the .STL file within the post, however, requires 3D printing. If you have a 3D printer, knock yourself out. Alternatively, you should be able to find a local business that does 3D printing. Send them the .STL file and ask to have printed in ABS material, this way it can withstand the heat. And then you can sand/paint to match, which is a simple matte black.
mpen97 is offline   Reply With Quote
Old 08-10-2019, 12:53 AM   #42
BeAboveAverage
Scooby Newbie
 
Member#: 505128
Join Date: Aug 2019
Default

Quote:
Originally Posted by heymonroe View Post
Yeah this is a good question, I would like this in my '17
Yes itís possible.
BeAboveAverage is offline   Reply With Quote
Old 10-06-2019, 03:59 PM   #43
Gardo
Scooby Newbie
 
Member#: 507126
Join Date: Oct 2019
Default

Is anybody selling the 3D printed pocket to finish off the swap
Gardo is offline   Reply With Quote
Old 10-06-2019, 09:32 PM   #44
TheModfatherInc
Scooby Newbie
 
Member#: 492499
Join Date: Oct 2018
Chapter/Region: NESIC
Location: Long Island NY
Vehicle:
2010 2.5i
SSM

Default

Quote:
Originally Posted by Gardo View Post
Is anybody selling the 3D printed pocket to finish off the swap
The dude who designed it is in this thread a few comments up, but if he doesnt want to print one, i'd be willing to for a few bucks assuming hes got no objection.
TheModfatherInc is offline   Reply With Quote
Old 10-07-2019, 09:40 AM   #45
c1em3ntchua
Scooby Newbie
 
Member#: 459594
Join Date: Dec 2016
Default

Quote:
Originally Posted by TheModfatherInc View Post
The dude who designed it is in this thread a few comments up, but if he doesnt want to print one, i'd be willing to for a few bucks assuming hes got no objection.
Please do go ahead. I'm based in Singapore so it doesn't make sense for me to print it and ship it over to the USA. The design is open-source anyway, so enjoy
c1em3ntchua is offline   Reply With Quote
Old 10-09-2019, 11:11 AM   #46
TheModfatherInc
Scooby Newbie
 
Member#: 492499
Join Date: Oct 2018
Chapter/Region: NESIC
Location: Long Island NY
Vehicle:
2010 2.5i
SSM

Default

Quote:
Originally Posted by c1em3ntchua View Post
Please do go ahead. I'm based in Singapore so it doesn't make sense for me to print it and ship it over to the USA. The design is open-source anyway, so enjoy
In that case, any suggestions on print orientation/settings? Thinking standing on the thin flat edge or 45 degrees may be easiest. Lots of overhangs/support to deal with
TheModfatherInc is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 04:29 PM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2019 Axivo Inc.
Copyright ©1999 - 2019, North American Subaru Impreza Owners Club, Inc.

As an Amazon Associate I earn from qualifying purchases.