|
![]() Brakes & Suspension Forum sponsored by The Tire Rack |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#51 |
Scooby Newbie
Member#: 179875
Join Date: May 2008
Chapter/Region:
SCIC
Location: OC
Vehicle:2006 WRX CGM |
![]() is there a How-to Brake pad install for 06+ wrx?
* Registered users of the site do not see these ads.
|
![]() |
![]() |
![]() |
#52 |
Scooby Specialist
Member#: 106248
Join Date: Jan 2006
Chapter/Region:
NESIC
Location: New Hampshire
Vehicle:2020 Taco 2000 RS 2.5 |
![]() Check out this thread:
http://forums.nasioc.com/forums/show...lacement+4+pot a few other things I learned in the process (if you didn't know already): -if you are doing rotors too, and they are stuck on, you can put some screws into the 2 threaded holes in the rotor to help break it loose from the hub -be very careful with the pin spring (holds the pins in)... very easy to break/bend -don't trust the guy at your local auto parts store to get you the right parts... I came home thinking I was all set to go and was just about to replace the pads when I noticed the ones I purchased were for 2005-earlier (non-4-pot). Further research revealed the rotor wouldn't fit either. Unfortuneately the store was closed for the weekend once I noticed this. -avoid letting air in through the M/C or you could run into issues with the ABS pump. |
![]() |
![]() |
![]() |
#53 |
Scooby Newbie
Member#: 225836
Join Date: Oct 2009
|
![]() can anyone post how to replace the rear strut mounts and stabilizer links??..the Subaru dealership wants to charge me about $600 for the job. I rather just buy the parts online and do it myself
|
![]() |
![]() |
![]() |
#54 |
Scooby Specialist
Member#: 9731
Join Date: Aug 2001
Location: Parkin Harder than Jewpac can.
Vehicle:2k2 wrx '13 Audi S4 Midnight Gray |
![]() im having issues finding a tutorial on rebuilding calipers, did i miss something in here?
|
![]() |
![]() |
![]() |
#55 |
Scooby Guru
Member#: 7958
Join Date: Jul 2001
Location: Plains of Eastern Montana
Vehicle:09 GH B+ |
![]() there is a four pot rebuild thread floating around- it's a very similar process for sliders and Brembo's
|
![]() |
![]() |
![]() |
#56 |
Scooby Guru
Member#: 147776
Join Date: May 2007
Chapter/Region:
NWIC
Location: Seattle, WA
Vehicle:2001 Forester 2013 Scion FR-S |
![]() Does anyone have any writeups for Wheel Bearings or Tie Rods?
|
![]() |
![]() |
![]() |
#57 |
Scooby Specialist
Member#: 96951
Join Date: Sep 2005
Chapter/Region:
MAIC
Location: Carlisle, PA
Vehicle:2004 wrx sedan '10 Outback 6mt-wifey's |
![]() wheel bearing write-up: http://forums.nasioc.com/forums/showthread.php?t=787070
|
![]() |
![]() |
![]() |
#58 |
Scooby Guru
Member#: 32459
Join Date: Feb 2003
Chapter/Region:
Tri-State
Location: NY
Vehicle:02 WRX VF34 (SOLD) Junior Tuned 301whp |
![]() Here is my write up on rear / front knuckles
http://forums.nasioc.com/forums/show....php?t=1917942 http://forums.nasioc.com/forums/show....php?t=1835257 Trailing arm bushings: http://forums.nasioc.com/forums/show....php?t=2000683 Last edited by txl146; 06-23-2010 at 07:57 PM. |
![]() |
![]() |
![]() |
#59 |
Scooby Specialist
Member#: 180710
Join Date: May 2008
Chapter/Region:
TXIC
Location: Corpus Christi
Vehicle:2006 Sti WRB WFC# 229 |
![]() Just wondering what steering rack are interchangeable for what years. Also any advantages for swaps from newer to older years.
|
![]() |
![]() |
![]() |
#60 |
Scooby Specialist
Member#: 131261
Join Date: Nov 2006
Chapter/Region:
NESIC
Location: Greenwich, CT
Vehicle:2007 SWP STi 2.5xtr 2003 Corvette ZO6 400whp |
![]() The links to the two threads at scooby mods for brake rotor/pad replacement don't seem to be working... any other links for changin rotors/pads on an 07 STi?
|
![]() |
![]() |
![]() |
#61 | |
Scooby Newbie
Member#: 164121
Join Date: Nov 2007
Chapter/Region:
Tri-State
Location: CT
Vehicle:2005 WRX EvoIII 16G EFI Logics Tuned |
![]() Quote:
http://www.iwsti.com/forums/how-inst...e-updated.html Pads (vid) http://www.hspn.tv/?do=showtag&videoid=44&tagid=18 PS your car looks good (I think it's you, on rt. 58?) |
|
![]() |
![]() |
![]() |
#62 | |
Scooby Specialist
Member#: 131261
Join Date: Nov 2006
Chapter/Region:
NESIC
Location: Greenwich, CT
Vehicle:2007 SWP STi 2.5xtr 2003 Corvette ZO6 400whp |
![]() Quote:
|
|
![]() |
![]() |
![]() |
#63 | |
Scooby Newbie
Member#: 164121
Join Date: Nov 2007
Chapter/Region:
Tri-State
Location: CT
Vehicle:2005 WRX EvoIII 16G EFI Logics Tuned |
![]() Quote:
![]() Actually a week or two ago when it was nice out I think you and someone else who owns the s2k were outside with both hoods popped. I noticed as I had to slow down a ton for a slow moving bus in front. |
|
![]() |
![]() |
![]() |
#64 | |
Scooby Specialist
Member#: 131261
Join Date: Nov 2006
Chapter/Region:
NESIC
Location: Greenwich, CT
Vehicle:2007 SWP STi 2.5xtr 2003 Corvette ZO6 400whp |
![]() Quote:
Yea the s2k owner is my room-mate.... do you post in the danbury thread>? |
|
![]() |
![]() |
![]() |
#65 | |
Scooby Newbie
Member#: 164121
Join Date: Nov 2007
Chapter/Region:
Tri-State
Location: CT
Vehicle:2005 WRX EvoIII 16G EFI Logics Tuned |
![]() Quote:
![]() I don't typically post in the Danbury thread, I have a few times but I'm not a regular. |
|
![]() |
![]() |
![]() |
#66 |
Scooby Specialist
Member#: 134248
Join Date: Dec 2006
Chapter/Region:
SWIC
Location: Ahwatukee, AZ
Vehicle:2007 STi-Stage2 -RIP "Desert Sand on White" |
![]() Thanks for starting this thread. It gave me all the info/courage I needed to install my SS Lines and bleed the system.
Much Appreciated! |
![]() |
![]() |
![]() |
#67 |
Scooby Newbie
Member#: 239341
Join Date: Feb 2010
Chapter/Region:
MWSOC
Location: Lafayette, Indiana
Vehicle:98 2.5RS BDP benms.com |
![]() I have a '94 Impreza L 1.8l, 2WD and I was wondering if there was any info on putting a sway bar on the rear end. I know there are kits and such for AWD Impreza's but I'm having trouble finding any info on 2WD's. Thanks.
Cory |
![]() |
![]() |
![]() |
#68 |
Scooby Specialist
Member#: 180710
Join Date: May 2008
Chapter/Region:
TXIC
Location: Corpus Christi
Vehicle:2006 Sti WRB WFC# 229 |
![]() Any info on steering rack interchangeability?
|
![]() |
![]() |
![]() |
#69 |
Merci Buckets
Moderator Member#: 88606
Join Date: Jun 2005
Chapter/Region:
MWSOC
Location: Michigan
Vehicle:2018 Grand Cherokee Velvet Red Pearl |
![]() I'm not sure if there is any info out there. Its not something I recall seeing anywhere. I might have to do the same thing on a rally car build I'm helping a friend with. The best I can figure is that we'll need to weld some brackets in place and probably need to use wagon rear lateral links.
|
![]() |
![]() |
![]() |
#70 |
Scooby Specialist
Member#: 26739
Join Date: Oct 2002
Chapter/Region:
NWIC
Location: Offshore
|
![]() Hi there, i have a 03 WRX with a bad power steering pump (it is leaking, and making a lot of noise). Does anyone have a writeup handy? (i searched, and will continue searching
![]() dealership wanted 800ish dollars for this, i figure it can't be that bad ![]() Thanks in advance for any help. |
![]() |
![]() |
![]() |
#71 | |
Merci Buckets
Moderator Member#: 88606
Join Date: Jun 2005
Chapter/Region:
MWSOC
Location: Michigan
Vehicle:2018 Grand Cherokee Velvet Red Pearl |
![]() Quote:
|
|
![]() |
![]() |
![]() |
#72 |
Scooby Newbie
Member#: 197221
Join Date: Dec 2008
Chapter/Region:
Tri-State
Location: NY
Vehicle:2008 WRX VF48 EFI Logics Tuned!!! |
![]() Last edited by theboz32; 10-09-2010 at 03:12 PM. Reason: i'm retarded sorry for the post i just saw it |
![]() |
![]() |
![]() |
#73 |
Scooby Newbie
Member#: 215990
Join Date: Jul 2009
Location: marietta GA
Vehicle:2006 WRX STI grey |
![]() Any 'How to adjust e-brake' thread for a 06 STI?
|
![]() |
![]() |
![]() |
#74 |
Scooby Specialist
Member#: 33979
Join Date: Mar 2003
Chapter/Region:
South East
Location: Charlotte, NC
Vehicle:2006 STi WRB |
![]() Two adjustments one at lever and one at the pads.
|
![]() |
![]() |
![]() |
#75 |
Scooby Newbie
Member#: 266556
Join Date: Dec 2010
Chapter/Region:
NESIC
Location: Boston MA
Vehicle:2002 down and dirty outback wagon |
![]() this seriously made replacing my suspension way easier than I thought it would be
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
AZP Installs -Your Tri-state Brake and Suspension Installers- | AZP Installs | Suspension/Brakes/Handling | 10 | 09-09-2008 08:35 PM |
Ten+ simple rules for Brakes/Steering/Suspension - READ THIS BEFORE POSTING! | Butt Dyno | Brakes, Steering & Suspension | 5 | 04-09-2008 12:25 PM |
ssautochrome install walkthrough? | Ceyvme | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 2 | 09-06-2006 07:46 PM |
kyb agx and spring install walkthrough?? | CXspeed | Newbies & FAQs | 4 | 05-09-2006 11:45 AM |
Boost Gauge Install Walkthrough? | Uncle Ben | Electrical & Lighting | 4 | 07-15-2003 05:31 PM |