2015 STI build - Page 3

405HP_Z06 · 07-11-2022, 04:21 PM

Very nice work!

* Registered users of the site do not see these ads.

alexmartynyuk · 08-15-2022, 11:42 AM

Project is still in progress. Finished porting the heads finally. Many updates coming soon.

405HP_Z06 · 08-15-2022, 11:59 AM

What are you doing for rings and did you specify bore finish roughness specifications?

alexmartynyuk · 08-15-2022, 06:12 PM

Quote:

Originally Posted by 405HP_Z06

What are you doing for rings and did you specify bore finish roughness specifications?

Ring gap has not been set yet if thats your question. I haven't started assembly yet. As for finish roughness I did not specify or request any particular finish.

405HP_Z06 · 08-15-2022, 06:15 PM

Quote:

Originally Posted by alexmartynyuk

Ring gap has not been set yet if thats your question. I haven't started assembly yet. As for finish roughness I did not specify or request any particular finish.

What rings are you using?

alexmartynyuk · 08-16-2022, 02:30 AM

Quote:

Originally Posted by 405HP_Z06

What rings are you using?

The rings that were included with the JE Ultra pistons.

405HP_Z06 · 08-16-2022, 08:41 AM

thanks! Cool build and nice progress.

alexmartynyuk · 05-24-2023, 03:29 AM

I hate when people start build threads and never finish! I'm talking about myself here as I feel guilty that I haven't posted much.

Had a few set backs, project is still ongoing.

To keep a long story short darton block was a waste of time and money because unfortunately the machinist botched the sleeve job, lost the sleeves, case halves and had to buy two pistons sizes because of this and lots of time on my end was wasted.

After going back to the drawing board me and my bro have decided to go with the IAG 1150 case halves and keep our rotating assembly of BC I beam rods/stock crank/ JE ultra series pistons.

More pics and posts will follow soon and sorry for not updating the thread.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-11-2022, 04:21 PM	#51
405HP_Z06 Scooby Newbie Member#: 216153 Join Date: Jul 2009 Chapter/Region: TXIC Location: Arlington, Tx Vehicle: 2015 STi LE WRB Pearl	Very nice work! * Registered users of the site do not see these ads.

08-15-2022, 11:42 AM	#52
alexmartynyuk Scooby Specialist Member#: 191967 Join Date: Oct 2008 Location: Vancouver Vehicle: 2005 EVO VIII instagram @_amtuned_	Project is still in progress. Finished porting the heads finally. Many updates coming soon.

08-15-2022, 11:59 AM	#53
405HP_Z06 Scooby Newbie Member#: 216153 Join Date: Jul 2009 Chapter/Region: TXIC Location: Arlington, Tx Vehicle: 2015 STi LE WRB Pearl	What are you doing for rings and did you specify bore finish roughness specifications?

08-16-2022, 08:41 AM	#57
405HP_Z06 Scooby Newbie Member#: 216153 Join Date: Jul 2009 Chapter/Region: TXIC Location: Arlington, Tx Vehicle: 2015 STi LE WRB Pearl	thanks! Cool build and nice progress.

05-24-2023, 03:29 AM	#58
alexmartynyuk Scooby Specialist Member#: 191967 Join Date: Oct 2008 Location: Vancouver Vehicle: 2005 EVO VIII instagram @_amtuned_	I hate when people start build threads and never finish! I'm talking about myself here as I feel guilty that I haven't posted much. Had a few set backs, project is still ongoing. To keep a long story short darton block was a waste of time and money because unfortunately the machinist botched the sleeve job, lost the sleeves, case halves and had to buy two pistons sizes because of this and lots of time on my end was wasted. After going back to the drawing board me and my bro have decided to go with the IAG 1150 case halves and keep our rotating assembly of BC I beam rods/stock crank/ JE ultra series pistons. More pics and posts will follow soon and sorry for not updating the thread.