MPS_UTECLogger v2.0 software is here! - calling all UTEC users! - Page 6

filbert · 10-30-2010, 02:45 AM

Dead thread... but in case anyone is still trying to get this to work... I got the trial and got it working pretty quickly. I just installed an AEM UEGO and picked up a second Serial-USB adapter and will test that tomorrow.

However, based on the lack of updates in this thread or on the website, I'm guessing it's not supported anymore and will be looking at the UTEC Interface (UTI) instead which has been updated this year.

* Registered users of the site do not see these ads.

wrxsubie2008 · 11-08-2010, 09:15 AM

This sounds like a cool program will defentily try it once i get my utec. Hopefully it will arive tomorrow.

wrxsubie2008 · 11-08-2010, 09:15 AM

What is some good software to start out with while using the utec. Mine is arriving hopefully tomorrow

filbert · 11-08-2010, 09:21 PM

I got this to work with my UTEC but it's having problems with my AEM UEGO. It works for several seconds, then craps out and gets stuck on the last reading. The rest of the UTEC info continues to updates correctly, it's just the AFR that stops. If I disconnect and reconnect, it does not work. I have to close out and re-load it, but then it will freeze again after a minute, making the AFR logging useless. I tried logging in directly to the UTEC and UEGO using PUTTY (I'm on Vista which has no HyperTerminal) and those seem to work fine, I'm not getting strange AFR values or anything.

I'm going to check out UTI as soon as some PayPal funds clear and see if that works any better.

bcblues · 11-08-2010, 09:35 PM

I never could get it to work at all.

filbert · 11-22-2010, 01:35 AM

Ok, it seems the problem was with my computer. I was using my work computer, an HP Elitebook 6930p running Vista.

I just switched to an old VAIO I got from my mom running XP with USB 1.1 drivers (couldn't get USB2.0 drivers to work after reinstalling XP) and both the UTEC and UEGO work fine with this setup.

Also, i found an USB-to-Dual Serial Port cable from Fry's so I can hook both devices up to a single USB port.

Garrek11 · 10-05-2011, 08:37 PM

I can't seem to get the logger to work. Im running the utec with LC-1 and its says there is a error if I have both plugged in and if im trying to just log the utec it trys to connect but then doesnt show anything?

And I seem to be having a problem with the utec communicating with the TPS and MAP?

I found a link to a explanation but the link doesnt work for me.
http://www.burago.com/wrx/Files/WRX-...er%20Guide.pdf

filbert · 10-06-2011, 09:47 AM

Just the logger doesn't work? or you can't even get connected with both? does the UTEC and LC1 both connect fine on their own (use hyperterminal or putty). What is the error? I've seen that pdf many times, i'm sure there are other copies on other sites.

Garrek11 · 10-06-2011, 08:20 PM

Hyperterminal works with utec
LC-1 connects to its own software

So they both will connect seperatly to there own. But neither of them will connect in the logger. Except sometimes I can get the utec to connect but then it seems to just freez before it can do anything.

filbert · 10-06-2011, 08:42 PM

Hmmm... I don't know. You're using two separate serial ports and cables? I would say check that the connection/protocol settings for both are correct in UTECLogger, but I haven't used an LC1 so I probably can't help you much...

Garrek11 · 10-06-2011, 09:05 PM

Ya to serperate ones both go from serial to usb.

matthewhiggins118 · 07-07-2012, 08:51 PM

So with this can you tune it or Just view it?

FreshWhiteWagon · 07-15-2015, 11:53 PM

I have a utec standalone for a 04-07 Sti if anyone is interested . Message me

10-05-2011, 08:37 PM	#132
Garrek11 * Banned * Member#: 227747 Join Date: Oct 2009 Chapter/Region: NWIC Location: Spokane WA Vehicle: 2006 STI (BW S363) SGM	I can't seem to get the logger to work. Im running the utec with LC-1 and its says there is a error if I have both plugged in and if im trying to just log the utec it trys to connect but then doesnt show anything? And I seem to be having a problem with the utec communicating with the TPS and MAP? I found a link to a explanation but the link doesnt work for me. http://www.burago.com/wrx/Files/WRX-...er%20Guide.pdf Last edited by Garrek11; 10-05-2011 at 09:11 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Calling all UTEC users in NoVA/DC/MD area	Chino1	Mid Atlantic Impreza Club -- MAIC	22	01-03-2008 05:27 PM
Calling all UTEC and/or Tuner users - need some help	lancelucas	North West Impreza Club Forum -- NWIC	0	11-02-2006 11:26 PM
calling houston UTEC users	datdudedennis	Texas Impreza Club Forum -- TXIC	6	03-06-2003 08:08 AM
EcuTek Delta ECU - calling all DDash users	Ken C	Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo)	0	10-03-2002 03:09 AM
Calling all intake users (kindof)	mike270	Normally Aspirated Powertrain	3	01-06-2002 07:49 PM

10-30-2010, 02:45 AM	#126
filbert Scooby Specialist Member#: 39661 Join Date: Jul 2003 Chapter/Region: MWSOC Location: Chicago Vehicle: 2017 BRZ WRB	Dead thread... but in case anyone is still trying to get this to work... I got the trial and got it working pretty quickly. I just installed an AEM UEGO and picked up a second Serial-USB adapter and will test that tomorrow. However, based on the lack of updates in this thread or on the website, I'm guessing it's not supported anymore and will be looking at the UTEC Interface (UTI) instead which has been updated this year. * Registered users of the site do not see these ads.

11-08-2010, 09:15 AM	#127
wrxsubie2008 Scooby Newbie Member#: 262393 Join Date: Oct 2010 Chapter/Region: MAIC Location: Southwest PA Vehicle: 2008 Subaru WRX White	This sounds like a cool program will defentily try it once i get my utec. Hopefully it will arive tomorrow.

11-08-2010, 09:15 AM	#128
wrxsubie2008 Scooby Newbie Member#: 262393 Join Date: Oct 2010 Chapter/Region: MAIC Location: Southwest PA Vehicle: 2008 Subaru WRX White	What is some good software to start out with while using the utec. Mine is arriving hopefully tomorrow

11-08-2010, 09:21 PM	#129
filbert Scooby Specialist Member#: 39661 Join Date: Jul 2003 Chapter/Region: MWSOC Location: Chicago Vehicle: 2017 BRZ WRB	I got this to work with my UTEC but it's having problems with my AEM UEGO. It works for several seconds, then craps out and gets stuck on the last reading. The rest of the UTEC info continues to updates correctly, it's just the AFR that stops. If I disconnect and reconnect, it does not work. I have to close out and re-load it, but then it will freeze again after a minute, making the AFR logging useless. I tried logging in directly to the UTEC and UEGO using PUTTY (I'm on Vista which has no HyperTerminal) and those seem to work fine, I'm not getting strange AFR values or anything. I'm going to check out UTI as soon as some PayPal funds clear and see if that works any better.

11-08-2010, 09:35 PM	#130
bcblues Scooby Specialist Member#: 17256 Join Date: Apr 2002 Chapter/Region: South East Location: America's Outback Vehicle: 18 Outback on the road....	I never could get it to work at all.

11-22-2010, 01:35 AM	#131
filbert Scooby Specialist Member#: 39661 Join Date: Jul 2003 Chapter/Region: MWSOC Location: Chicago Vehicle: 2017 BRZ WRB	Ok, it seems the problem was with my computer. I was using my work computer, an HP Elitebook 6930p running Vista. I just switched to an old VAIO I got from my mom running XP with USB 1.1 drivers (couldn't get USB2.0 drivers to work after reinstalling XP) and both the UTEC and UEGO work fine with this setup. Also, i found an USB-to-Dual Serial Port cable from Fry's so I can hook both devices up to a single USB port.

10-06-2011, 09:47 AM	#133
filbert Scooby Specialist Member#: 39661 Join Date: Jul 2003 Chapter/Region: MWSOC Location: Chicago Vehicle: 2017 BRZ WRB	Just the logger doesn't work? or you can't even get connected with both? does the UTEC and LC1 both connect fine on their own (use hyperterminal or putty). What is the error? I've seen that pdf many times, i'm sure there are other copies on other sites.

10-06-2011, 08:20 PM	#134
Garrek11 * Banned * Member#: 227747 Join Date: Oct 2009 Chapter/Region: NWIC Location: Spokane WA Vehicle: 2006 STI (BW S363) SGM	Hyperterminal works with utec LC-1 connects to its own software So they both will connect seperatly to there own. But neither of them will connect in the logger. Except sometimes I can get the utec to connect but then it seems to just freez before it can do anything.

10-06-2011, 08:42 PM	#135
filbert Scooby Specialist Member#: 39661 Join Date: Jul 2003 Chapter/Region: MWSOC Location: Chicago Vehicle: 2017 BRZ WRB	Hmmm... I don't know. You're using two separate serial ports and cables? I would say check that the connection/protocol settings for both are correct in UTECLogger, but I haven't used an LC1 so I probably can't help you much...

10-06-2011, 09:05 PM	#136
Garrek11 * Banned * Member#: 227747 Join Date: Oct 2009 Chapter/Region: NWIC Location: Spokane WA Vehicle: 2006 STI (BW S363) SGM	Ya to serperate ones both go from serial to usb.

07-07-2012, 08:51 PM	#137
matthewhiggins118 Scooby Newbie Member#: 197478 Join Date: Dec 2008 Chapter/Region: MWSOC Location: Wittenberg.Wi Vehicle: 2003 Wrx Sedona Red	So with this can you tune it or Just view it?

07-15-2015, 11:53 PM	#138
FreshWhiteWagon Scooby Newbie Member#: 385242 Join Date: Mar 2014 Chapter/Region: Tri-State Location: Central NJ Vehicle: 99 Civic Black	I have a utec standalone for a 04-07 Sti if anyone is interested . Message me