FS - V7 JDM SB, Hyperflow TMIC, JDM STI IC

Gruppe-S · 09-04-2004, 04:39 AM

Hi everyone,

We need to make room for the container next week:

*JDM V7 Short Block - This is a complete short block and a great solution to hold more power! Features forged crankshaft, forged rods, forged pistons, semi-closed deck. Was leaked down before being dissambled (customer requested heads only). Includes water pump, oil pump, crank position sensor, oil/water temp sensors.
$999 Shipped!

*HyperFlow TMIC - This Hyperflow TMIC was installed on our shop car for about 5 dyno pulls and 35 miles of driving.

It's basically good as new.
$699 Shipped!

*JDM TMIC w/ Ypipe - This is a JDM V7 TMIC w/ Y-pipe. Very good condition, some fins were bent by my clumsiness while taking the picture.
$475 Shipped!

Thanks,

Gary
[email protected]
www.gruppe-s.com
510-783-5300
510-783-4300 fax

* Registered users of the site do not see these ads.

kosoku · 09-04-2004, 06:28 AM

Is the left side of the STi intercooler bent? or is it just the picture?

redcoupe · 09-04-2004, 08:08 PM

How many miles on the engine?

Gruppe-S · 09-09-2004, 01:47 AM

Kosoku - It's just the picture. I think maybe my head was blocking the light

Redcoupe - The V7 engines range from 10,000-20,000 miles on average. All our engines are leaked down and compression tested before and after arrival. This motor would be in good condition

Thanks,

Gary
Gruppe-S

09-04-2004, 04:39 AM	#1
Gruppe-S Former Vendor Vendor Sales Rating: (65) Member#: 23216 Join Date: Aug 2002 Location: Lake Forest, CA \| 949-457-1234 Vehicle: 2006 949-457-1234 949-457-1234	FS - V7 JDM SB, Hyperflow TMIC, JDM STI IC Hi everyone, We need to make room for the container next week: *JDM V7 Short Block - This is a complete short block and a great solution to hold more power! Features forged crankshaft, forged rods, forged pistons, semi-closed deck. Was leaked down before being dissambled (customer requested heads only). Includes water pump, oil pump, crank position sensor, oil/water temp sensors. $999 Shipped! *HyperFlow TMIC - This Hyperflow TMIC was installed on our shop car for about 5 dyno pulls and 35 miles of driving. It's basically good as new. $699 Shipped! *JDM TMIC w/ Ypipe - This is a JDM V7 TMIC w/ Y-pipe. Very good condition, some fins were bent by my clumsiness while taking the picture. $475 Shipped! Thanks, Gary [email protected] www.gruppe-s.com 510-783-5300 510-783-4300 fax * Registered users of the site do not see these ads.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS VA: Turbo XS HyperFlow TMIC	Bugeyeballa	Engine/Power/Exhaust	20	01-15-2010 09:19 AM
FS. V7 jdm sti tmic	666stars	Engine/Power/Exhaust	1	11-17-2009 07:45 PM
Any benefit of going with Hyperflow TMIC over JDM STI TMIC?	gopsu	Newbies & FAQs	4	06-08-2009 12:14 AM
APS TMIC with STI IC Splitter	ohm	Newbies & FAQs	8	05-28-2009 04:01 PM
hyperflow tmic v. v7 tmic	DoctorNick	Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo)	3	01-23-2005 03:38 PM

09-04-2004, 06:28 AM	#2
kosoku Scooby Specialist Member Sales Rating: (2) Member#: 51373 Join Date: Dec 2003 Chapter/Region: SCIC Location: Orange County Vehicle: 2008 Nissan Titan 04 SV650, WSMC #606	Is the left side of the STi intercooler bent? or is it just the picture?

09-04-2004, 08:08 PM	#3
redcoupe Scooby Newbie Member Sales Rating: (0) Member#: 27233 Join Date: Oct 2002 Location: St. Louis, MO Vehicle: 2003 wrx Sedona red	How many miles on the engine?

09-09-2004, 01:47 AM	#4
Gruppe-S Former Vendor Vendor Sales Rating: (65) Member#: 23216 Join Date: Aug 2002 Location: Lake Forest, CA \| 949-457-1234 Vehicle: 2006 949-457-1234 949-457-1234	Kosoku - It's just the picture. I think maybe my head was blocking the light Redcoupe - The V7 engines range from 10,000-20,000 miles on average. All our engines are leaked down and compression tested before and after arrival. This motor would be in good condition Thanks, Gary Gruppe-S