|
|
|
|
Thread Tools | Display Modes |
04-05-2006, 03:32 PM | #1 |
n00b Moderator
Moderator Member#: 811
Join Date: Jan 2000
Location: WA
Vehicle:2000 RS-Ej20G It tastes like burning |
EJ20G injector o-rings and spacers
EDIT:
Part numbers down below. Hi all, I am looking for part numbers for the replaceable injector parts. What I found pulling my injectors and rails off is more parts than are shown in the manual. On my engine I have; Insulator doughnut that goes on the head (listed in the manual) 2 o-rings for the injector in the rail (listed in the manual) injector cap rubber isolator (listed in the manual) thin nylon injector to rail spacer (NOT in the manual) plastic spacer ring (NOT in the manual) I will take some pictures tonight. I was hoping someone could shed a light on part numbers suitable for replacement. Thanks, Rob
* Registered users of the site do not see these ads.
Last edited by rob; 05-03-2006 at 11:21 AM. |
04-05-2006, 04:02 PM | #2 |
Scooby Newbie
Member#: 33072
Join Date: Feb 2003
Chapter/Region:
MAIC
Location: Centreville, VA
Vehicle:'95 EJ20g v1 STI RA BRP, 2001 GC8 chassis |
You may want to consult sixpack subaru. He's hooked up a lot of people with JDM part numbers.
|
04-05-2006, 04:09 PM | #3 |
Scooby Guru
Member#: 177
Join Date: Aug 1999
Chapter/Region:
NWIC
Location: Austin, Texas, USA
Vehicle:The 93 W/EJ20K-sold Subaru-less :( |
the real question is
are there any other usdm cars that use the pintle style injectors? i don't know .. i made custom rails (combo of 1.8 +ej20G) i used (93) 1.8 rail to manafold doughnuts .. which were identical to the G |
04-10-2006, 07:06 PM | #4 |
n00b Moderator
Moderator Member#: 811
Join Date: Jan 2000
Location: WA
Vehicle:2000 RS-Ej20G It tastes like burning |
Here's the pic;
Can anybody identify part numbers that work for the 6 pieces? Numbers 3 and 4 are the ones I don't see in the various US service manuals. Thanks, Rob |
04-11-2006, 11:36 AM | #5 |
Scooby Guru
Member#: 177
Join Date: Aug 1999
Chapter/Region:
NWIC
Location: Austin, Texas, USA
Vehicle:The 93 W/EJ20K-sold Subaru-less :( |
sorry i got nothign for you .. post this over in the pre 2002 forum
|
04-11-2006, 12:52 PM | #6 |
n00b Moderator
Moderator Member#: 811
Join Date: Jan 2000
Location: WA
Vehicle:2000 RS-Ej20G It tastes like burning |
So the 1.8 injectors you played with did not have the extra spacers (3 and 4)?
|
04-11-2006, 01:02 PM | #7 |
Scooby Guru
Member#: 832
Join Date: Jan 2000
Chapter/Region:
RMIC
Location: Teh Ghetto Garage, CO
Vehicle:99 2.5RS, '85 911 '73 914 and 2012 BRZ |
hmmm,
I don't remember there being more than 3 o-rings on the Ej20G injectors I pulled and sent to Silvialost. You might shoot him a PM and ask him about it since I no llonger have the parts in hand. The injectors looked the same as the ones you have pictured... |
04-11-2006, 01:19 PM | #8 |
Scooby Guru
Member#: 177
Join Date: Aug 1999
Chapter/Region:
NWIC
Location: Austin, Texas, USA
Vehicle:The 93 W/EJ20K-sold Subaru-less :( |
12345 |
04-16-2006, 11:05 PM | #9 |
n00b Moderator
Moderator Member#: 811
Join Date: Jan 2000
Location: WA
Vehicle:2000 RS-Ej20G It tastes like burning |
still need some help with this.
|
04-16-2006, 11:45 PM | #10 |
Scooby Specialist
Member#: 34545
Join Date: Mar 2003
Chapter/Region:
MWSOC
Location: Worthington, Ohio
Vehicle:1999 GC8 74f |
hrmm I dont have a clue I know that some nissan injector parts are useable. NOt too sure about the ej20g ones though.
|
05-03-2006, 11:11 AM | #11 |
n00b Moderator
Moderator Member#: 811
Join Date: Jan 2000
Location: WA
Vehicle:2000 RS-Ej20G It tastes like burning |
A kind fellow in Australia looked up the parts for an RS Liberty. Here they are for future reference;
1 16608aa020 Seal-fuel Injector x4 2 16698aa020 O Ring-injector x4 3 16697aa000 Ring-injector x4 4 16696aa000 Spacer-injector x4 5 16698aa010 O Ring-injector x4 6 16607aa031 Insul Fuel Inject x4 It's a little spendy for a full replacement, but injector fuel leaks are bad m'kay. -Rob Last edited by rob; 05-03-2006 at 11:18 AM. |
05-15-2006, 10:44 AM | #12 |
Scooby Guru
Member#: 177
Join Date: Aug 1999
Chapter/Region:
NWIC
Location: Austin, Texas, USA
Vehicle:The 93 W/EJ20K-sold Subaru-less :( |
might as well keep this stuff together
http://forums.nasioc.com/forums/show....php?t=1004263 |
12-07-2006, 10:40 AM | #13 |
Scooby Specialist
Member#: 21764
Join Date: Jul 2002
Chapter/Region:
RMIC
Location: Salty Lake
Vehicle:Some GDM V8, JDM Flat 4 X2 |
Got a quick question.
Im about to put STi injectors into my EJ20G using RS fuel rails, from what i can tell ill need all the listed part numbers from the top except the #6, sense this a ball style. can someone correct me? thanks Kirill |
12-07-2006, 12:12 PM | #14 |
n00b Moderator
Moderator Member#: 811
Join Date: Jan 2000
Location: WA
Vehicle:2000 RS-Ej20G It tastes like burning |
I wouldn't think so. I am pretty sure the ej20g injectors are the only ones that need the extra spacers. I would guess you would only need the standard o-rings that come on the STi injectors.
-Rob |
12-07-2006, 12:19 PM | #15 |
Scooby Specialist
Member#: 21764
Join Date: Jul 2002
Chapter/Region:
RMIC
Location: Salty Lake
Vehicle:Some GDM V8, JDM Flat 4 X2 |
So would i wana use 2.5rs fuel rail to manifold O-ring, and for Inj. to fuel rail i wana use STi?
I know that there are a couple of ppl that have done this, and i just want to make sure that i get the proper parts. Im flippin my manifold, doing STi injectors and a parallel fuel system, that im all trying to do in 5days, so i dont want to get held back becouse of wrong o-rings. thanks kirill |
12-07-2006, 01:15 PM | #16 |
Scooby Guru
Member#: 177
Join Date: Aug 1999
Chapter/Region:
NWIC
Location: Austin, Texas, USA
Vehicle:The 93 W/EJ20K-sold Subaru-less :( |
rs rails ?
thats new to me |
12-07-2006, 02:34 PM | #17 |
Scooby Specialist
Member#: 66739
Join Date: Jul 2004
Chapter/Region:
MWSOC
Location: Medina, Ohio
Vehicle:2002 WRX wagon silver |
what style is an EJ20K using? and around what cc/min do they flow? i am going to check mine(may have them cleaned n blueprinted) soon and wouldlike to try and source replacement in the US first.
thanks in advance guys! --keith |
12-07-2006, 03:17 PM | #18 |
Scooby Guru
Member#: 832
Join Date: Jan 2000
Chapter/Region:
RMIC
Location: Teh Ghetto Garage, CO
Vehicle:99 2.5RS, '85 911 '73 914 and 2012 BRZ |
My EJ20K is using yellow top injectors, which I believe are 440cc, just like the Ej20G greytops. I have both a '96 and '97 manifold sitting on the bench in my garage right now, and other than some changes to the larger rails to accomodate the under manifold inlet, I see no difference on the little stub rails that actually hold the injectors. Let me check tonight and I will see if the part numbers are the same...
And the only RS rails I ever heard about being used for injector upgrades were '99's that supposedly take STi pink top feeds, and were used some by RS-T guys back in the day... |
12-07-2006, 08:16 PM | #19 |
Scooby Guru
Member#: 177
Join Date: Aug 1999
Chapter/Region:
NWIC
Location: Austin, Texas, USA
Vehicle:The 93 W/EJ20K-sold Subaru-less :( |
yeah take some pictures ... it would be awesome if the stis fit the K rails
|
12-07-2006, 08:59 PM | #20 |
Scooby Specialist
Member#: 113036
Join Date: Apr 2006
Chapter/Region:
BAIC
Location: Bay Area
|
I thought the EJ20G greys were 380cc. Is that only on the older models?
|
12-07-2006, 09:46 PM | #21 |
Scooby Specialist
Member#: 43128
Join Date: Sep 2003
Location: SLC
Vehicle:92 RWD, 96 FWD 05 AWD |
I checked today and the USDM STi yellow tops WILL fit the 98RS fuel rails.
Thanks Kirill(snowman4us) |
12-07-2006, 10:43 PM | #22 |
Scooby Guru
Member#: 177
Join Date: Aug 1999
Chapter/Region:
NWIC
Location: Austin, Texas, USA
Vehicle:The 93 W/EJ20K-sold Subaru-less :( |
ah 98rs
greys are 440s tested by at least 3 sources that i know of legayc SS pinks are 380(ish) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Wrx Top Feed Injector O-rings And 06 Sti Bumper | c'dalerider | Private 'Wanted' Classifieds | 0 | 11-06-2009 11:38 AM |
Wtb: ej20G heads w/ intake and cam gears fuel injectors etc | 91turbosedaan | Private 'Wanted' Classifieds | 1 | 01-07-2009 11:33 AM |
FS/FT Injector O-rings and BOV Gasket. NEW | Rexwagon03 | Engine/Power/Exhaust | 10 | 01-05-2009 06:54 AM |
stock wrx parts, turbo,IC,injectors, ring and pinion | gotti | Private 'For Sale' Classifieds | 17 | 01-31-2006 11:04 AM |
legacy injectors, 3.9 ring and pinion | gotawd | Private 'Wanted' Classifieds | 2 | 05-04-2005 04:21 PM |