|
![]() |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Scooby Newbie
Member#: 510928
Join Date: Jan 2020
Chapter/Region:
NWIC
Location: Portland OR
Vehicle:1979 DL Red |
![]() So I have been working on this for a couple months now. I will do my best to keep it updated. I have a 1979 subaru wagon. I am putting a EJ22T from a 91 legacy with a 5speed into my wagon. Including full drive train. Its definitely a project. Here is a link to my photos. I will update them when I have more along with adding them to this post.
http://s38.photobucket.com/user/88ub...bile%20Uploads ![]() ![]() ![]()
* Registered users of the site do not see these ads.
|
![]() |
![]() |
![]() |
#2 |
Scooby Specialist
Member#: 110078
Join Date: Mar 2006
Location: Long Island N.Y.
Vehicle:02 Bugeye JDM STi OBP BLACK |
![]() Subscribed
|
![]() |
![]() |
![]() |
#3 |
Scooby Specialist
Member#: 13530
Join Date: Dec 2001
Chapter/Region:
NWIC
Location: Cascadia
Vehicle:EA63 , EA81T, EJ20G, EJ205 |
![]() Very cool! I've got a '75 4WD wagon that I plan to swap a 12A into, so I'm interested to see what you've got planned!
|
![]() |
![]() |
![]() |
#4 |
Scooby Newbie
Member#: 510928
Join Date: Jan 2020
Chapter/Region:
NWIC
Location: Portland OR
Vehicle:1979 DL Red |
![]() Working on the cross member right now. The left one is from the 79 and the right is out of the 91 legacy donor car. I am hoping to shorten the 91 x-member so I can use the power steering and then the mounting locations for the A arm's. If not the 79 x-member will need to be notched and re strengthened so the up pipe will be able to fit.
![]() |
![]() |
![]() |
![]() |
#5 |
Scooby Newbie
Member#: 510928
Join Date: Jan 2020
Chapter/Region:
NWIC
Location: Portland OR
Vehicle:1979 DL Red |
![]() Finally got my cross member back. Its started as a 91 legacy turbo cross member and was shortened to fit into the 78 frame rails. About 1 3/4 inches needed to be cut off of each side. Using the 91 legacy cross member will allow me to use the 91 suspension and the power stearing from the 91. I am able to use the stick motor mounts from the 91 also. It's a snug fit. But it doens fit. I'm going to have to notch the frame rails a tiny bit so the valve cover bolt doesnt sit on it. If anyone needs measurements or help. I would be happy to help. This project has been a handfull to say the least.
[IMG] ![]() [IMG] ![]() [IMG] ![]() [IMG] ![]() Last edited by Toh79DL; 04-03-2020 at 11:56 PM. |
![]() |
![]() |
![]() |
#6 |
Scooby Specialist
Member#: 13530
Join Date: Dec 2001
Chapter/Region:
NWIC
Location: Cascadia
Vehicle:EA63 , EA81T, EJ20G, EJ205 |
![]() The folks over at www.ultimatesubaru.org/forum would eat this up!
|
![]() |
![]() |
![]() |
#7 | |
Scooby Newbie
Member#: 510928
Join Date: Jan 2020
Chapter/Region:
NWIC
Location: Portland OR
Vehicle:1979 DL Red |
![]() Quote:
Last edited by Toh79DL; 04-24-2020 at 08:57 PM. |
|
![]() |
![]() |
![]() |
#8 |
Scooby Newbie
Member#: 510928
Join Date: Jan 2020
Chapter/Region:
NWIC
Location: Portland OR
Vehicle:1979 DL Red |
![]() |
![]() |
![]() |
![]() |
#9 |
Scooby Specialist
Member#: 21676
Join Date: Jul 2002
Chapter/Region:
NWIC
Location: Pacific Northwet
Vehicle:RX 02Foz90XT692SVX Black |
![]() Following...
Send me your log in info and user name for USMB, I'll see if I can get your account fixed (I'm a mod there) |
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|