|
|
|
|
Thread Tools | Display Modes |
05-27-2020, 09:29 PM | #701 |
Scooby Newbie
Member#: 515146
Join Date: May 2020
|
anyone know is there is a difference between the ej20k (1996) valvesprings and retainers and the 2002 wrx OR know a website i can get aftermarket springs and retainers for an ej20k, as the closest option they ever have for a 2.0l turbo is the 2002 wrx. tia
* Registered users of the site do not see these ads.
|
05-27-2020, 09:43 PM | #702 | |
Scooby Guru
Member#: 90539
Join Date: Jul 2005
Chapter/Region:
South East
Location: SWLA
Vehicle:My BOV goes COVFEFE! |
Quote:
The springs in the 96-98 dohc 2.5 and the ej20k are longer than the 02-05 wrx springs. I got a set of shims by ferrea that allowed the shorter ej205 size springs to work in my ej20k heads but ferrea doesn't have them anymore. The ones they sent me sucked anyway and I had to send them back because their sizes weren't accurate. Finally they returned in the correct size and I installed the dual supertech springs. The ej25d n/a heads have the same spring and valve setup as the ej20k, just different spring pressure and some had sodium filled valves. From what I remember, the shims ferrea made were 6.40mm thick, which made the ej205 spec supertech dual springs fit correctly. They replaced the oem spring seats. I also had supertech valves for the n/a ej25d in my ej20k heads. If you contact user 2pot, he may be able to share the specs of some shims he had made for his setup. I think a machine shop made his, they looked to be of better quality than the ferrea. |
|
07-21-2020, 08:27 PM | #703 |
Scooby Newbie
Member#: 397454
Join Date: Jul 2014
Chapter/Region:
W. Canada
Location: Winnipeg
Vehicle:1997 GC8 STi |
|
07-21-2020, 08:47 PM | #704 |
Scooby Guru
Member#: 90539
Join Date: Jul 2005
Chapter/Region:
South East
Location: SWLA
Vehicle:My BOV goes COVFEFE! |
93-01 Impreza (GC and GM) axles are same length in front. You just need to confirm if your old axle is male or female on the inner end and if you need an axle with the abs ring on the outer. I've bought aftermarket axles and they came with pressed on abs rings, which I tapped off with a mallet and punch because my knuckles had no room for the ring. The 02-07 Impreza(GD) wagon axles are also the correct splines inner and outer and have the correct length.
|
07-21-2020, 09:32 PM | #705 | |
Scooby Newbie
Member#: 397454
Join Date: Jul 2014
Chapter/Region:
W. Canada
Location: Winnipeg
Vehicle:1997 GC8 STi |
Quote:
Male: |
|
07-22-2020, 07:50 AM | #706 |
Scooby Guru
Member#: 90539
Join Date: Jul 2005
Chapter/Region:
South East
Location: SWLA
Vehicle:My BOV goes COVFEFE! |
Yes. Also pay attention to whether your car has abs. If not, you will need to remove the abs rings from the axles.
|
07-23-2020, 09:22 PM | #707 |
Scooby Newbie
Member#: 397454
Join Date: Jul 2014
Chapter/Region:
W. Canada
Location: Winnipeg
Vehicle:1997 GC8 STi |
|
03-06-2022, 06:01 AM | #708 |
Scooby Newbie
Member#: 379271
Join Date: Jan 2014
|
after reading 29 pages cant believe i couldn't find a 98 USDM EJ25D Full gasket kit part number ? anyone know whats the part number for a 98 USDM EJ25D Full gasket kit ?
i was told and read on Nasioc 3x that for the ej20k wrx motor, everyone just uses the 98 USDM EJ25D gasket kit and uses everything in that kit besides the HG because its different |
08-04-2023, 11:19 AM | #709 |
*** Banned ***
Member#: 534914
Join Date: Jul 2023
|
Plastic coolant tank on EJ20G intake manifold
TANK ASSEMBLY - WATER 21132AA001 (number is correct but not in Jamie's catalog) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EJ20G & EJ20K Parts | awdeclipseguy | 1993 - 2001 Impreza Specific Parts | 17 | 06-15-2009 07:04 PM |
EJ20G Gasket Part Numbers... | scoobydorift | Subaru Conversions | 13 | 02-14-2005 10:43 PM |
Official XT Oil Filter Part Number thread | BrysImpreza | Forester Forum | 8 | 10-29-2003 11:23 PM |
NAPA Part numbers- can we have a nice thread with numbers listed? | Tex-WReX2 | Service & Maintenance | 5 | 12-15-2001 09:21 AM |