|
|
|
|
Thread Tools | Display Modes |
02-02-2008, 03:32 PM | #26 |
*** Banned ***
Member#: 2992
Join Date: Nov 2000
Chapter/Region:
NESIC
Location: Connecticut, USA
Vehicle:02 WRX Sedan Silver |
tinywrex, thanks for providing an explanation of how your launch control works.
http://tinywrex.wordpress.com/2008/0...-how-it-works/
* Registered users of the site do not see these ads.
|
02-02-2008, 03:39 PM | #27 |
*** Banned ***
Member#: 82734
Join Date: Mar 2005
|
Maybe we can take a look at the NO LIFT SHIFT stuff again
|
02-02-2008, 04:24 PM | #28 | |
Scooby Specialist
Member#: 114528
Join Date: May 2006
Location: Outer space
Vehicle:2002 Space Shuttle Discovery |
Quote:
|
|
02-02-2008, 04:46 PM | #29 |
Scooby Guru
Member#: 118209
Join Date: Jun 2006
Chapter/Region:
MWSOC
Location: North Dakota
Vehicle:2015 WRX Limitec |
it isn't lean if there is zero fuel in the chamber to ignite. ignition cut is dangerous because now you have a full charge of fuel that is going to ignite somewhere. either in your exhaust manifold, turbo, or cat.
|
02-02-2008, 06:18 PM | #30 |
Scooby Guru
Member#: 15822
Join Date: Feb 2002
Location: TOPOHTO
Vehicle:1999 WRB GM6 2.34 LR destroker |
so once it's patched, do you actually see a new "map" in the ROM where you can change the settings?
I can't check, as my ECU id isn't supported yet (A4TJ111C-RT) |
02-02-2008, 06:25 PM | #31 |
Scooby Newbie
Member#: 94490
Join Date: Aug 2005
Location: Australia
|
no problems yet with the 6-puck i have in place.
Plus a friend has been dragin for at least 5 years and only just busted his first half shaft. that was on a 91 RS liberty with a 5spd dogbox that has ****ty half shaft joints and shafts half the thickness. and was more probably to do with the dccd centre he has now putting 70% to the back wheels. Load the drive train-up and she is apples.Side step the clutch with no slack taken in the drive-train and you are asking for trouble. |
02-02-2008, 06:35 PM | #32 |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
|
02-02-2008, 06:36 PM | #33 |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
|
02-02-2008, 06:38 PM | #34 | |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
Quote:
|
|
02-02-2008, 06:48 PM | #35 |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
|
02-02-2008, 08:49 PM | #36 |
Scooby Specialist
Member#: 156973
Join Date: Aug 2007
Chapter/Region:
International
Location: Adelaide, Australia
Vehicle:2002 ADM WRX STi STi Black/Blue |
any chance of patching the AUDM 2002 2.0L sti?
I can forward you a copy of my rom if required. Also, will this cause any compatability problems when tuning the patched ROM with Enginuity and reflashing my patched and tuned ROM with ecuFlash? |
02-02-2008, 11:15 PM | #37 |
Scooby Newbie
Member#: 116036
Join Date: May 2006
Location: Ft Lauderdale.
Vehicle:2015 WRX STi DGM |
Please dear god update us when you have a 32bit for the 06-07's (pleaasseee)
Ill be your best friend (By best friend I mean send you at least $50..depending on my current funds and all) Last edited by gaveup; 02-02-2008 at 11:29 PM. |
02-03-2008, 12:50 AM | #38 |
Scooby Specialist
Member#: 98645
Join Date: Oct 2005
Chapter/Region:
NESIC
Location: Lawrence,ma
Vehicle:2002 WRX Wagon PSM |
So I can't view the tables in EcuFlash version 1.29 that i run on my win2k system. But i can on version 1.34. BUT in the getting started FAQ it states that 1.34 will only work on WinXP and Vista. So why Can i run it on my win2k system, or will it not be able to flash?
OR Can I modify the tables in 1.34 then flash them with 1.29? |
02-03-2008, 01:34 AM | #39 |
Scooby Specialist
Member#: 114528
Join Date: May 2006
Location: Outer space
Vehicle:2002 Space Shuttle Discovery |
sweet! I just patched my rom w/ the launch control. Truly awesome!!
thank you xswrex!!! |
02-03-2008, 01:40 AM | #40 | |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
Quote:
No compatibility issues or problems, you can even use Enginuity (or any editor for that matter) for editing as long as you port the XML parameters. |
|
02-03-2008, 01:44 AM | #41 | |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
Quote:
i believe you can, the flashing process just reads the file in binary format, it reads bytes, it transmits bytes! |
|
02-03-2008, 01:48 AM | #42 |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
|
02-03-2008, 02:48 AM | #43 |
Scooby Newbie
Member#: 117334
Join Date: Jun 2006
Location: Indiana
Vehicle:2002 Impreza WRX WRB |
Wwwwwwwwoooooooowwwwwwwww!!!!
Just installed the patch and changed my map. This is really amazing stuff Thanks a lot!! I used the A4SGE01C revision in an 02 wrx and every thing went smooth, good instructions. A little change to the speed threshold and it will be smooth consistent launches. I was using a delta rpm of 3200 and a speed threshold of 20 k/hr and was hitting the limiter after the launch. Its a little wet out and I had a little too much wheel spin but to be expected.
Thanks again. Parker |
02-03-2008, 02:57 AM | #44 |
Scooby Specialist
Member#: 114528
Join Date: May 2006
Location: Outer space
Vehicle:2002 Space Shuttle Discovery |
|
02-03-2008, 03:53 AM | #45 |
Scooby Guru
Member#: 140444
Join Date: Feb 2007
Chapter/Region:
NWIC
Location: Near Seattle, WA
Vehicle:05 Stage Free LGT ATP 3076, 6MT, AVO FMIC |
So how hard would it be to put the threshold and delta in RAM?
And then write a little utility to tweak those values from a laptop using a Tactrix cable? |
02-03-2008, 03:53 AM | #46 |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
|
02-03-2008, 04:09 AM | #47 |
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
|
02-03-2008, 04:11 AM | #48 |
Scooby Specialist
Member#: 157532
Join Date: Aug 2007
Chapter/Region:
MWSOC
Location: Iowa
Vehicle:2002 MY03 EJ207 E85 Dom 1.5XTR Twinscroll! |
can the A4SGE01C patch be used with any 02 ECU as long as the xml code is inserted into the proper file in ecu flash?
EDIT: Tried it, and the inital values set for the RPM Delta and speed values are not 0 upon opening the rom for the first time in ECU Flash. I would have to say it's not safe use this A4SGE01C patch on an A4SGD10C rom, even though they are both USDM MY02 revisions. Last edited by simon021; 02-03-2008 at 04:28 AM. |
02-03-2008, 04:52 AM | #49 | ||
Scooby Newbie
Member#: 87255
Join Date: May 2005
Location: Greece
Vehicle:2002 Impreza WRX given up emptying PMs... |
Quote:
Quote:
As others have suggested you can use A4SGE01C ROM on any USDM MY02 because it is the version that fixes some issues, that is why i created a patch for that first. If you want a specific A4SGD10C you just have to wait! You should not mix things up in your head! Last edited by xswrex; 02-03-2008 at 09:51 AM. |
||
02-03-2008, 09:36 AM | #50 |
Scooby Specialist
Member#: 142133
Join Date: Feb 2007
Chapter/Region:
MAIC
Location: Virginia - hate it
Vehicle:2011 CC Sport and a Cummins Dually |
I used the A4SGE01C patch for my usdm02. Using the tinypatcher.exe, here's what I got:
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Launch Control on 2004 WRX | Doomsti | AccessPort | 18 | 11-16-2012 03:16 PM |
Launch Control on 32bit ECU | Nuke209 | Open Source Reflashes | 126 | 05-17-2008 10:49 AM |
Help with wiring in launch control on an 05 WRX. | Sir Wagon | UTEC | 2 | 03-07-2008 04:45 PM |
Failed NY state Inspection because of Launch Control on UTEC? | vipernj | Engine Management & Tuning | 2 | 01-24-2006 06:10 PM |
utec remote switch launch control on 4eat | topgrinder | Engine Management & Tuning | 1 | 03-27-2003 08:34 PM |