|
|
|
|
Thread Tools | Display Modes |
11-29-2006, 06:43 PM | #51 |
Scooby Newbie
Member#: 120482
Join Date: Jul 2006
|
The point was made earlier in this thread that aftermarket synchro parts for the 5MT weren't available. Well PPG have them available and I have included a quote from their website below. Follow the link for more info on whats available for WRXs. Hope this helps those looking to replace synchros.
"At PPG we make the Synchromesh rings and hubs considerably stronger than factory components and incorporate our high quality materials and heat treating processes into the finished product ensuring durability you can rely upon for years to come." http://www.ppgearbox.com.au/html/wrxinformation.htm
* Registered users of the site do not see these ads.
|
11-29-2006, 07:04 PM | #52 | |
Guest
Member#:
|
Quote:
Personally, I've never had a problem with a SUBARU syncro unless it has been abused or misused for long periods of time. |
|
11-29-2006, 10:02 PM | #53 |
*** Banned ***
Member#: 104035
Join Date: Dec 2005
Chapter/Region:
TXIC
Location: arlington, tx
Vehicle:2002 Blu-Baru stg2 sukt im ready 4 stg3 |
ok so i experienced my 2nd shearing of 1st and 2nd......im proud to say actually lol. actually the 1st time it broke they (warranty company) replaced it with a factory salvaged unit. this time im getting a "new" tranny put in my 02 bugeye. my question is have they since fixed the ever so popular gearbox problem. just curious as to how accurate the suby service center was with me. he already tried to tell me that the sti ra gearbox would not fit in my car so i was already skeptical by that remark. just curious considering the warranty is buying this 4000 dollar tranny brand new not remanufactureed and i dont want to have the same problems that i have had in the past. all im running is downpipe, header and uppipe, catback, cobb intake, gfb hybrid bov, fixing to go with the 3/16 mod from boostkits when it gets out of the shop, and a dc sports short throw. aggresive driver but no clutch dumps, synchro grinds, more or less full throttle with smooth shifts. dont think im overpowering it by no means. lemme know what u think. thanks !!!!!blubaru nation!!!!!
|
01-11-2007, 06:41 AM | #54 |
Scooby Specialist
Member#: 82148
Join Date: Mar 2005
Chapter/Region:
SCIC
Location: SoCal
Vehicle:1992 Daihatsu Charade |
|
01-11-2007, 06:50 AM | #55 |
Scooby Specialist
Member#: 82148
Join Date: Mar 2005
Chapter/Region:
SCIC
Location: SoCal
Vehicle:1992 Daihatsu Charade |
I do have a question that many of you may be interested in. Calculating from my elementary math skills, our cars have an approximate 29% power loss. That is a big number in my books and I'd love to lower that number.
Carbon fiber driveshaft does help reduce a little of that power loss due to its light rotational mass and diameter. However, the majority of the drivetrain loss is in the transmission and its gears. Then there's the lightweight clutch and flywheel. But that's common knowledge on NASIOC. What I'm interested in is reduction of lower loss in the transmission unit itself. As far as I know, our gears are made of steel for cost, strength, and shock absorption reasons. Have there been any lightweight gears made from different materials (titanium comes to mind) that would significantly reduce this transmission loss? A quick search on Google and Eng-tips.com came up with no available product (we're not discussion about Subaru's only, but motorsports in general for any make). Eng-tips hinted that Titanium was tried before yet failed miserable approximately 5-10 years ago due to some problems they could not overcome (the engineering jargon was hieroglyphics to me). The majority of the issue I believe with the titanium gears they tried was its inability to absorb shock due to too much deflection. Are there any engineers that would be interested in this topic and research along with me? |
01-11-2007, 08:00 PM | #56 |
Guest
Member#:
|
Ti is too weak for an enviorment such as a transmission or engine. Ti is not god in high temp situations either. Over a short amount of time (compared to how long the stock parts are designed to last) the Ti parts will need to be 'refreshed' back to specs.
Basically...the peices in the 6MT and what PPG have are the best possible. What is this Xtrac you refer to? |
01-12-2007, 01:00 AM | #57 | |
Scooby Specialist
Member#: 82148
Join Date: Mar 2005
Chapter/Region:
SCIC
Location: SoCal
Vehicle:1992 Daihatsu Charade |
Quote:
http://www.xtrac.com/mainindex.htm Makes trannies for Le Mans, Dakar Rally, Formula One, WRC. They will custom make a tranny for you upon request. Like I said, I'm not looking at any drop-in solutions. I'm trying to see if there are possibilities of different materials for gears in transmissions to reduce rotational mass and power loss. This is for ANY car, not just Subarus. Then maybe someone can custom make something that would be beneficial for the entire modification community. |
|
01-12-2007, 08:26 AM | #58 |
Scooby Newbie
Member#: 115260
Join Date: May 2006
Chapter/Region:
MAIC
Location: Dover, DE
Vehicle:04 WRX 205/22E Hybrid w/ VF39 |
A large portion of the extra power loss is due to the twice the amount of ring/pinions, differential bearings, wheel bearings, axles, and cv joints that it has to travel through before it hits all four wheels. I don't think the transmission design is the main power loss culprit here.
|
01-12-2007, 11:15 AM | #59 |
Scooby Specialist
Member#: 28685
Join Date: Nov 2002
Location: Reno, Nevada
Vehicle:2004 FXT 4EAT very STi'd |
Bingo. To reduce the drivetrain loss significantly, convert to RWD.
|
01-12-2007, 08:43 PM | #60 | |
Scooby Specialist
Member#: 82148
Join Date: Mar 2005
Chapter/Region:
SCIC
Location: SoCal
Vehicle:1992 Daihatsu Charade |
Quote:
Is there such a thing as lightweight bearings? Converting to RWD is not an option here for this topic. |
|
01-12-2007, 08:51 PM | #61 |
Guest
Member#:
|
Just do carbon gears and bearings.
BAM!!!!!! JDM lightweight version. |
03-21-2007, 02:04 AM | #62 |
Scooby Newbie
Member#: 54871
Join Date: Feb 2004
Chapter/Region:
International
Location: Costa Rica
Vehicle:1999 Impreza GT White |
I have had trouble twice, but not gears, there were a broken roll and a syncro trouble 4 and 5th.
I bougth MRT 3rd Edition book and I found that they recommend some extracooling after 150 °C... and for track use... I decided to install a cooling system for the trany, like Forester Turbo S MY99 does from factory, but better. So I installed a cooler at the original intercooler bay and a oil pump sucking from transfer case to cooler, then the pump and then returning cooled oil to front differential. I haven´t finished my proyect, bacause I want to control it by a electronic, and temp imput device. So I need a maximun target temp I´m running a EJ20 FMIC, 288 WHP, 275 lb-pie, stock gears, 4.444 final ratio, Castrol GL-5, Torsen front, LSD central and LSD rear pics: www.imprezacr.com What temperature is recommended for trany operation? Would cooling improve and prevent gear trouble? |
03-21-2007, 10:10 AM | #63 |
Scooby Specialist
Member#: 110304
Join Date: Mar 2006
Location: Crestline, CA
Vehicle:2004 Volvo S60R No more Subie |
Cooling the oil is good. Especially if you can set up a way to redistribute the oil back over at least the first 2 or 3 gears, instead of relying on the "splash" lubrication design that it has.
However, an oil cooler will basically just help to keep the oil from breaking down sooner. In my opinion, gear failures in the transmissions are mainly caused by shockload and, as a result, deflection of the mainshaft (input shaft). Cooler gear oil won't keep that shaft from flexing. |
04-06-2008, 08:30 PM | #64 |
Scooby Specialist
Member#: 143149
Join Date: Mar 2007
Chapter/Region:
Tri-State
Location: No evo 9, no sti swap wrx
Vehicle:2006 gmc envoy stealth |
Hey Guys, Im looking at two different gearing options. The STI RA and the STI SE gear sets. Which would you reccomend for me to upgrade my 2007 wrx 5mt with and which will behave better daily driving/ spirited driving. I wont be exceeding 350 hp in any form. Probably around 300.
And does anyone know if the OBX racing helical front LSD that fits the 02- 05 wrx will function correctly in my 07 wrx case? ra gear First Gear 3.083 Second Gear 2.062 Third Gear 1.545 Fourth Gear 1.151 Fifth Gear 0.825 se gear First Gear 3.166 Second Gear 1.882 Third Gear 1.296 Fourth Gear 0.972 Fifth Gear 0.738 stock 3.454 (1st) 1.947 (2nd) 1.366 (3rd) 0.972 (4th) 0.738 (5th) Last edited by Dubstar112; 04-06-2008 at 09:21 PM. |
04-07-2008, 12:44 PM | #65 | |
Scooby Specialist
Member#: 94494
Join Date: Aug 2005
Chapter/Region:
NWIC
Location: Seattle
Vehicle:2005 Element 92x Black |
Quote:
In fact, since you have a push-style clutch, I'm pretty sure all you need is a WRX specific front diff a speedo gear to install a Legacy GT transmission in your car. The OBX one you mentioned would fit the bill for either a re-build or the Legacy GT transmission. |
|
04-07-2008, 01:08 PM | #66 | |
Scooby Guru
Member#: 133146
Join Date: Nov 2006
Location: SC
Vehicle:07 FPgreen 7.37@95 WRX VF39+E85 12.0, 121mph |
Quote:
|
|
04-23-2008, 06:32 PM | #67 |
Scooby Specialist
Member#: 114530
Join Date: May 2006
Chapter/Region:
NESIC
|
Yeah, could someone confirm/deny it? I read that LGT 5MT gears are same as JDM STI non-RA gears. So they should be stronger than WRX gears. Also there are very few reports of LGT transmission failures even on high-powered LGTs, which with 2.5L push way more torque than 2.0L WRX...
|
10-12-2009, 01:03 PM | #68 |
Scooby Specialist
Member#: 97577
Join Date: Oct 2005
Chapter/Region:
BAIC
Location: OR->WA->TX->OR->CA
Vehicle:2001 IS 300 White |
bump..?
|
10-13-2009, 08:19 AM | #69 |
Former Vendor
Member#: 99694
Join Date: Nov 2005
Chapter/Region:
MAIC
Location: 09 SS GTR
Vehicle:2015 rocketbunny brz red |
Holy dead thread bump batman!
Are the LGT gears an upgrade for the 06-07 WRX owners? No. I mean, gear ratio is different, and the numerically higher ratios will be marginally stronger, but it would be unnoticeable. If you had the power to break an 06-07 box, you'll break an LGT box. As for that material, design, lightweight comment before. 1) Gears need to be steel. Steel is typically heavy. The majority of steels have densities in the same .28x lb/cubic inch range. Something like aluminum lacks the mechanical properties that would allow them to be subjected to the stress associated with gear-train drive systems. If you think that "steel" is too limited, remember that there are HUNDREDS of different types of steel, each with unique mechanical properties. Add to that the, literally, infinite modes of heat treatment and post processing to achieve specific mechanical properties, and you'll find that "steel isn't steel isn't steel". 2) The astronomical cost of exotic materials, like magnesium or berylium, would... have astronomical costs. They COULD be designed to be much stronger and much lighter, but they'd also cost about as much as the purchase price of a small secluded island off the coast of South Africa. 3) You have physical dimension requirements. Gear ratios are dictated by tooth count. To have the number of teeth required for the ratios you want, you need to have enough of a diameter gear to achieve it. To do THAT, you have to use a specific amount of material. You could do things like scallop the sides of the gears, or make the gears narrower to reduce weight and increase efficiency, but you sacrifice strength to do so. Plus, our gears are loaded in both directions (depending on acceleration/deceleration), so any face modification would have to account for that. 4) In terms of efficiency, there is a notable increase in efficiency when switching from helical gears to straight cut gears. Less energy is wasted trying to push the gears longitudinally apart (thrust load, trying to walk one shaft towards the engine, and the other out the rear of the case) and the savings is transferred to the shaft and out to the wheels. If efficiency is your bag, opt for straight cuts over helical. You'll still lose some energy in other ways that you weren't losing with helical (some energy transferred into sound, for example), but the net energy lost will be less with straight cut gears than helical gears. 5) The AWD "stuff" does account for a decrease in performance. Still, you'd find not much more than a 2%-5% increase in economy if you DID convert to RWD (bypassing the front diff all together). Any gear change is going to impart some loss of efficiency. That's the nature of gear reduction/modification. You lose energy during the process. 6) If you want to idealize efficiency, get 4 rotary engines, mount one at each wheel, and direct drive them. Size the tire right, and you should be able to have a reasonably decent high-speed performer with enough boost. Actually getting off the line, however, would be a feat of black magic. Ever tried getting your Subaru rolling in 4th gear? Give it a shot before actually thinking this kind of thing is a good idea. The alternative to this is to use 4 electric motors at each wheel, direct drive them, and have a turbo diesel 4-cylinder bolted to a generator. Just my take on the lightweight, efficiency stand. Designing a system from the ground up would remove many of these concerns, but that's still impractical when it comes to cost. What can realistically be done, is modify the current offerings (new gears in a stock case), and that is limited as above. Phil Andrewtech Automotive |
12-30-2009, 03:16 PM | #70 |
Scooby Specialist
Member#: 144751
Join Date: Mar 2007
Chapter/Region:
MWSOC
Location: Granger, IN
Vehicle:02 WRX BW EFR E85 7064 TS WRB |
To bump this up again, I want to get back to the OP.
The root cause of gear tooth shear as the OP pointed out was shaft flex, mainly on the input. All of the talk in this thread has been about gears. Why? If the root cause of the failure is the input shaft, what options do we have to eliminate input shaft flex? Can we support the shaft at another location (I'm guess not)? Can we make a shaft out of stronger material? Heat treat and cyro treat the stock shaft? Anyone know what the material (obviously steel, more specifically) is on the stock input shaft and the treatments it received? |
01-12-2010, 09:36 PM | #71 |
Scooby Specialist
Member#: 234715
Join Date: Jan 2010
Chapter/Region:
RMIC
Location: cheyenne, wyoming
Vehicle:2003 wrx charcoal |
To find what kind of tranny u have is easy! Find a plate on the driver side of the vehicle when u pop the hood and in Japanese/Chinese it should read Fuji auto industries.
|
01-12-2010, 09:54 PM | #72 |
Scooby Specialist
Member#: 28685
Join Date: Nov 2002
Location: Reno, Nevada
Vehicle:2004 FXT 4EAT very STi'd |
I'm gonna go ahead and say that it won't be in Chinese.
|
01-13-2010, 03:53 PM | #73 |
Scooby Newbie
Member#: 174965
Join Date: Mar 2008
Chapter/Region:
MAIC
Location: Annapolis, Maryland
Vehicle:07 WRX VF43 OBP |
Well I know this doesn't have much to do with the thread, but people with transmission questions are usually looking for an upgrade.
It was said earlier that ppg are the best gears you can buy and many people can't afford them, but Albins makes a gearset that is both affordable and reliable(from tests by a few shops). Here is a link to the thread if anyone is interested: Albins Thread |
01-13-2010, 04:50 PM | #74 |
Former Vendor
Member#: 91335
Join Date: Jul 2005
Chapter/Region:
MAIC
Location: Fallston, MD
|
+1 I really like Albins gear sets myself and will choose them over other manufactures. I think most people recommended PPG since there was no other alternative at that time. Albins just started to sell their product to US and what was previously only available to race teams is now being offered to the public.
|
01-14-2010, 01:09 AM | #75 | |
Scooby Guru
Member#: 64364
Join Date: Jun 2004
Chapter/Region:
MAIC
Location: Northern Commonwealth
|
Quote:
Sure, it's news to most of us in the U.S. However, until someone does a fair side-by-side comparison with other solutions such as PPG and MFactory, all the hype isn't that helpful, other than saying there's another product available. All the Albins stuff I've heard/read basically sounds like a polished sales pitch. Almost like someone cut and pasted the words off a brochure. Also, one of the complaints about PPGs that folks throw out there are the high pricing. Who's to say that Albins won't be more expensive? One thing that I've pointed out in the various 6-speed versus PPG versus MFactory postings is what is the final cost? How much will it set back the person who's car that it's going into? You not only need to factor in the parts, there's install costs, downtime, etc. Artie from Agile - Have you actually experienced Albins in a Subaru or a different car manufacturer? Just curious. |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
technical discussion of $2 boost mod | 2manycarz | Forester Forum | 14 | 12-23-2006 11:05 PM |
An EJ22T, USDM WRX intake, and my 2005 RS... a technical discussion | Crashsector | Subaru Conversions | 3 | 07-25-2006 04:40 PM |
Martin/Park Crash, technical discussion thread | eurojax | Motorsports | 103 | 10-03-2005 06:53 PM |
STi Technical Discussions... We should move to NASIOC Technical | rlavalle | STi Forum Archive | 4 | 08-29-2003 12:14 AM |
Call for *technical* discussion of the new Wilwood 4 pot kit being sold | Concillian | Brakes, Steering & Suspension | 44 | 06-01-2002 12:52 AM |