|
|
|
|
Thread Tools | Display Modes |
11-15-2001, 01:48 AM | #1 |
Sooby Guru
Member#: 1914
Join Date: Jul 2000
Chapter/Region:
SWIC
Location: 2014 Q60S, 2016 Chevy SS
Vehicle:2000 2.5RS w/ EJ22T swap and N20. gone. : ( |
Anyone cross-referenced Suabru Fuel Injectors?
I am so tired of aftermarket parts for Subaru's being so darned expensive! EIGHT injectors for the Vette's I work on cost $295! And people tell me that 4 injectors for my car cost over $600!
Has anyone ever cross-referenced the Subaru injectors or am I screwed? Are they low or high Impedience? Thanks Eric
* Registered users of the site do not see these ads.
|
11-15-2001, 02:18 AM | #2 |
Scooby Guru
Member#: 6551
Join Date: May 2001
Chapter/Region:
MWSOC
Location: Carol Stream, IL
Vehicle:'01 GC8 Dinged STM '09 Concours 14 ABS Black |
eric i should have more details for you soon.. 8complex and i are going to see about fitting RX-7 Injectors in...and yes i agree with you...but just remember those designs you are suing on those vettes have been paid for since the 80's....this is a new game out here and an expensive one at that.
Jeremy |
11-15-2001, 02:20 AM | #3 |
Sooby Guru
Member#: 1914
Join Date: Jul 2000
Chapter/Region:
SWIC
Location: 2014 Q60S, 2016 Chevy SS
Vehicle:2000 2.5RS w/ EJ22T swap and N20. gone. : ( |
I hope you guys come up with some good news. do you know if they are High or low impedience?
Eric |
11-15-2001, 02:33 AM | #4 |
Scooby Guru
Member#: 6551
Join Date: May 2001
Chapter/Region:
MWSOC
Location: Carol Stream, IL
Vehicle:'01 GC8 Dinged STM '09 Concours 14 ABS Black |
high
|
11-15-2001, 02:35 AM | #5 |
Sooby Guru
Member#: 1914
Join Date: Jul 2000
Chapter/Region:
SWIC
Location: 2014 Q60S, 2016 Chevy SS
Vehicle:2000 2.5RS w/ EJ22T swap and N20. gone. : ( |
That's good. That means you can at least run low impedience if you need to.
Eric |
11-15-2001, 03:06 AM | #6 |
Scooby Specialist
Member#: 1911
Join Date: Jul 2000
Location: Seattle, WA, USA
Vehicle:2000 Impreza 2.5RS Silverthorn Metallic |
Eric:
Just bore out the injector bosses and use the Bosch injectors you probably have in the shop. That's what I am currently planning. Ben |
11-15-2001, 03:47 AM | #7 |
Scooby Guru
Member#: 6551
Join Date: May 2001
Chapter/Region:
MWSOC
Location: Carol Stream, IL
Vehicle:'01 GC8 Dinged STM '09 Concours 14 ABS Black |
ben i was wondering if that would work...get a set a 52lb/hr GM Bosch PFI injectors...they are 16.0-16.8 ohm injectors....but they aren't dual spray...which ours are and that might be a problem...i'd be concerned with fuel puddling on the cylinder head and running down the walls into the chamber.
jeremy |
11-15-2001, 12:14 PM | #8 |
Sooby Guru
Member#: 1914
Join Date: Jul 2000
Chapter/Region:
SWIC
Location: 2014 Q60S, 2016 Chevy SS
Vehicle:2000 2.5RS w/ EJ22T swap and N20. gone. : ( |
Here's another trick guys. Don't buy the Bosch injectors from GM. get the SVT injetors from Ford. They are a lot cheaper and exactly the same thing. THat's actually what we use on our Vettes. I was wondering if those would work. THey look very similar
Eric |
11-15-2001, 01:42 PM | #9 |
Scooby Specialist
Member#: 1911
Join Date: Jul 2000
Location: Seattle, WA, USA
Vehicle:2000 Impreza 2.5RS Silverthorn Metallic |
If you bore out the bosses, shouldn't the injectors seat deeply enough into the head to avoid puddling?
Ben |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fuel Injector Service | rsemrad | South East Region Forum | 0 | 06-02-2010 12:14 AM |
Anyone ever maxed out fuel injectors on stage 2 | freetors | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 14 | 04-29-2009 07:36 PM |
Has anyone tryed the APS Auxiliary fuel injector settup on there WRX? | 2002WRXSTi | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 8 | 03-08-2005 06:44 PM |
Need rubber wrx fuel injector o-ring or fuel injector | Shaitiger | Private 'Wanted' Classifieds | 2 | 02-11-2004 09:17 AM |
Fuel Injectors / Fuel system | JC SPORTS | Technical Forum Archive | 75 | 07-14-2000 08:51 PM |