|
|
|
|
Thread Tools | Display Modes |
|
06-03-2002, 01:52 PM | #1 |
Scooby Specialist
Member#: 12692
Join Date: Nov 2001
Chapter/Region:
MWSOC
Location: ...now i think i'm ready, to
Vehicle:bust a move check it out i'm rockin' steady |
my first CEL! woo hoo!
well my first CEL came on this morning...
"Code PO546 - Vehicle Speed, Idle Control, Aux" or something to that effect. What is it? Should I clear it? My Engine mods include TurboXS boost controller set at only 14psi and up-pipe. Thanks, Nirmit |
06-03-2002, 02:11 PM | #2 |
Scooby Guru
Member#: 8343
Join Date: Jul 2001
Chapter/Region:
MWSOC
Location: Atlanta, GA
Vehicle:2005 2012 Jeep 2013 DGM BRZ |
Actually PO546 is - Exhaust gas temperature sensor circult high input
Which actually means the EGT reading from the uppipe is too low. That means either your egt probe in the uppipe is history, or it fell out, is loose, or something to that affect. I pulled the same code a couple days ago, I still need to look under there and see what the deal is. |
06-03-2002, 02:19 PM | #3 |
Scooby Specialist
Member#: 12692
Join Date: Nov 2001
Chapter/Region:
MWSOC
Location: ...now i think i'm ready, to
Vehicle:bust a move check it out i'm rockin' steady |
the OBD2 scan tool I got stated "Vehicle Speed, Idle Control, Aux." Am I not reading it right?
Exhaust gas temperature sensor circult high input - Does that mean that my EGT's went too high and burned out my stock probe? I thought that a non-cat uppipe was suppose to reduce EGT's. I was actually getting a EGT gauge installed tomorrow - what timing. The car is driving normal, but I cleared the CEL anyways. I'll see if it comes on again and have the people that are installing my EGT gauge take a look tomorrow. Thanks, Nirmit |
06-03-2002, 02:44 PM | #4 |
Scooby Guru
Member#: 8343
Join Date: Jul 2001
Chapter/Region:
MWSOC
Location: Atlanta, GA
Vehicle:2005 2012 Jeep 2013 DGM BRZ |
That's probably the general category the CEL falls under, or maybe it just says that because it doesn't know. Here is a list of obd-2 codes for our cars:
http://www.northursalia.com/m...obd2/obd2.html The high input reading actually means the temperatures are too low. If you do a search for P0546 on the board you'll find a bunch of threads. Most of the time the EGT sensor in the uppipe has just worked itself loose. Phil |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Got my AP today!! woo hoo! | Devilprobably | Texas Impreza Club Forum -- TXIC | 11 | 11-15-2005 03:58 PM |
my first CEL- but i have stock intake and all my cats, hmm? | sicminded | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 20 | 06-06-2003 03:12 PM |
my car complete - woo hoo *56k beware* | Mr.Freeze | Member's Car Gallery | 29 | 06-01-2003 08:10 PM |
They finally delieverd my new Car!! Woo-hoo!! | Overtime | General Forum Archive | 2 | 05-15-2000 12:27 AM |
My First Mod Woo-hoo!!! | Ryan24 | North West Impreza Club Forum -- NWIC | 7 | 04-13-2000 06:18 PM |